Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Transponder Key Coil (Ignition Key Cylinder Light)*

·

Map Light Assembly

·

Spot Light Assembly LH and RH (for Front Side)

·

Spot Light Assembly LH and RH (for Rear Side)


*: w/o Smart Entry and Start System


WIRING DIAGRAM

E288064
0.656,0.594 1.49,0.76 0.833,0.167 10 false from Battery 3.01,0.615 3.25,0.781 0.24,0.167 10 false 4L 3.01,1.594 3.25,1.76 0.24,0.167 10 false 4D 3.01,1.99 3.25,2.156 0.24,0.167 10 false 4D 3,2.406 3.24,2.573 0.24,0.167 10 false 4D 3.031,0.396 3.188,0.563 0.156,0.167 10 false 1 3.052,1.406 3.208,1.573 0.156,0.167 10 false 7 3,1.813 3.208,1.979 0.208,0.167 10 false 13 3,2.219 3.208,2.385 0.208,0.167 10 false 12 3.604,0.781 4.104,0.948 0.5,0.167 10 false DOME 4.667,1.271 5.5,1.438 0.833,0.167 10 false DOME CUT 3.417,2.969 6.167,3.135 2.75,0.167 10 false Instrument Panel Junction Block Assembly 6,0.5 6.25,0.667 0.25,0.167 10 false 23 6.073,1.885 6.24,2.052 0.167,0.167 10 false 1 6.271,0.594 6.771,0.76 0.5,0.167 10 false DOMR 6.271,1.99 6.604,2.156 0.333,0.167 10 false ILE 1.417,4.448 1.573,4.615 0.156,0.167 10 false 2 4.51,4.448 4.667,4.615 0.156,0.167 10 false 4 1.635,4.448 1.969,4.615 0.333,0.167 10 false ILL+ 4.146,4.448 4.479,4.615 0.333,0.167 10 false ILL- 1.542,5.177 1.927,5.375 0.385,0.198 10 false F53 1.542,5.323 5.135,5.594 3.594,0.271 10 false Transponder Key Coil (Ignition Key Cylinder Light)* 0.281,6.167 0.521,6.333 0.24,0.167 10 false 10 0.552,6.167 0.74,6.333 0.188,0.167 10 false B 4.844,6.063 5.344,6.229 0.5,0.167 10 false RRMP 5.365,6.063 5.615,6.229 0.25,0.167 10 false 11 5.917,8.25 6.25,8.417 0.333,0.167 10 false MB 5.917,8.417 7.083,9.083 1.167,0.667 10 false Main Body ECU (Multiplex Network Body ECU) 4.979,8.396 5.313,8.563 0.333,0.167 10 false CTY 5.365,8.396 5.615,8.563 0.25,0.167 10 false 9 5.531,9.583 5.698,9.75 0.167,0.167 10 false 2 0.188,9.583 0.354,9.75 0.167,0.167 10 false 1 1.75,6.063 2.083,6.229 0.333,0.167 10 false OFF 1.75,7.76 2.083,7.927 0.333,0.167 10 false OFF 3.167,6.75 3.5,6.917 0.333,0.167 10 false OFF 4.417,6.75 4.75,6.917 0.333,0.167 10 false OFF 1.75,7.958 2,8.125 0.25,0.167 10 false ON 3.167,6.938 3.417,7.104 0.25,0.167 10 false ON 4.417,6.938 4.667,7.104 0.25,0.167 10 false ON 4.552,8.813 4.969,8.979 0.417,0.167 10 false GND 4.75,9.021 4.917,9.188 0.167,0.167 10 false 1 1,9.052 1.25,9.219 0.25,0.167 10 false S1 1,9.219 2.333,9.385 1.333,0.167 10 false Map Light Assembly 2.75,9.417 5.26,9.646 2.51,0.229 10 false *: w/o Smart Entry and Start System 1.25,6.75 2.167,7.083 0.917,0.333 10 false Personal Light Switch LH 1.25,8.396 2.146,8.74 0.896,0.344 10 false Personal Light Switch RH 2.677,7.417 3.542,7.76 0.865,0.344 10 false Interior Light DOOR Switch 3.813,7.417 4.802,7.771 0.99,0.354 10 false Interior Light ON/OFF Switch 1.75,6.271 2,6.438 0.25,0.167 10 false ON 2.104,0.771 3.052,0.958 0.948,0.188 10 false J/B-B

E287260
0.156,0.073 0.323,0.24 0.167,0.167 10 false 1 2.094,0.875 2.26,1.042 0.167,0.167 10 false B 2.094,2.271 2.26,2.438 0.167,0.167 10 false B 2.094,3.656 2.26,3.823 0.167,0.167 10 false B 2.094,5.052 2.26,5.219 0.167,0.167 10 false B 3.542,5.177 3.708,5.344 0.167,0.167 10 false E 3.542,3.792 3.708,3.958 0.167,0.167 10 false E 3.542,2.396 3.708,2.563 0.167,0.167 10 false E 3.542,1.01 3.708,1.177 0.167,0.167 10 false E 3.375,0.75 3.708,0.927 0.333,0.177 10 false CTY 3.385,2.135 3.708,2.313 0.323,0.177 10 false CTY 3.385,3.531 3.708,3.698 0.323,0.167 10 false CTY 1.865,5.052 2.031,5.219 0.167,0.167 10 false 2 1.729,5.635 4.333,5.854 2.604,0.219 10 false S12 1.615,4.24 4.354,4.583 2.74,0.344 10 false S11 1.583,1.458 4.26,1.802 2.677,0.344 10 false S9 1.604,2.854 4.302,3.156 2.698,0.302 10 false S10 5.49,0.063 5.656,0.229 0.167,0.167 10 false 2 1.583,1.625 4.26,1.969 2.677,0.344 10 false Spot Light Assembly LH (for Front Side) 1.604,3.021 4.302,3.323 2.698,0.302 10 false Spot Light Assembly RH (for Front Side) 1.615,4.406 4.354,4.75 2.74,0.344 10 false Spot Light Assembly LH (for Rear Side) 1.729,5.802 4.333,6.021 2.604,0.219 10 false Spot Light Assembly RH (for Rear Side) 3.75,5.177 3.917,5.344 0.167,0.167 10 false 4 1.865,3.656 2.031,3.823 0.167,0.167 10 false 2 1.865,2.271 2.031,2.438 0.167,0.167 10 false 2 1.865,0.875 2.031,1.042 0.167,0.167 10 false 2 3.385,4.917 3.708,5.083 0.323,0.167 10 false CTY 3.75,4.917 3.917,5.083 0.167,0.167 10 false 3 3.75,3.531 3.917,3.698 0.167,0.167 10 false 3 3.75,3.792 3.917,3.958 0.167,0.167 10 false 4 3.75,2.135 3.917,2.302 0.167,0.167 10 false 3 3.75,0.75 3.917,0.917 0.167,0.167 10 false 3 3.75,2.396 3.917,2.563 0.167,0.167 10 false 4 3.75,1.01 3.917,1.177 0.167,0.167 10 false 4


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION


*1: w/ Smart Entry and Start System

*2: for LHD



HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

2.PERFORM ACTIVE TEST USING GTS

B

6.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system* ON or OFF Perform the Active Test with interior light DOOR switch in the map light assembly turned on.

*: Refer to Description for the lights that are controlled by the illuminated entry system.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Circuit


Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4
OK:

All lights that are controlled by the illuminated entry system come on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT MAP LIGHT ASSEMBLY
3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4D instrument panel junction block connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-12 - S1-9 (CTY) Always Below 1 Ω
4D-12 or S1-9 (CTY) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E273530
1.333,0.25 1.75,0.5 0.417,0.25 4.833,0.25 5.25,0.5 0.417,0.25 3.625,1.51 3.396,1.51 3.396,1.51 3.281,1.115 false 0.208,0.115 0.521,0.313 0.313,0.198 10 false *a 1.469,0.292 1.781,0.49 0.313,0.198 10 false 4D 4.948,0.292 5.26,0.49 0.313,0.198 10 false MB 3.677,1.427 3.99,1.625 0.313,0.198 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4D-12 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system* ON or OFF Perform the Active Test with interior light DOOR switch in the map light assembly turned on.

*: Refer to Description for the lights that are controlled by the illuminated entry system.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Circuit


Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4
OK:

All lights that are controlled by the illuminated entry system come on.



Result:
Result Proceed to
OK A
NG (Map light and spot lights do not come on) B
NG (Ignition key cylinder light does not come on) C
NG (All lights that are controlled by the illuminated entry system do not come on) D



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

7.INSPECT MAP LIGHT ASSEMBLY

C

10.INSPECT TRANSPONDER KEY COIL

D

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
7.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4D instrument panel junction block connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-12 - S1-9 (CTY) Always Below 1 Ω
4D-12 or S1-9 (CTY) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E273530
1.333,0.25 1.75,0.5 0.417,0.25 4.833,0.25 5.25,0.5 0.417,0.25 3.625,1.51 3.396,1.51 3.396,1.51 3.281,1.115 false 0.208,0.115 0.521,0.313 0.313,0.198 10 false *a 1.469,0.292 1.781,0.49 0.313,0.198 10 false 4D 4.948,0.292 5.26,0.49 0.313,0.198 10 false MB 3.677,1.427 3.99,1.625 0.313,0.198 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4D-12 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

10.INSPECT TRANSPONDER KEY COIL
a.

Remove the transponder key coil.

Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>REMOVAL


b.

Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY COIL - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY COIL - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4D instrument panel junction block connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-13 - F53-4 (ILL-) Always Below 1 Ω
4D-13 or F53-4 (ILL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E273530
1.333,0.25 1.75,0.5 0.417,0.25 4.833,0.25 5.25,0.5 0.417,0.25 3.625,1.51 3.396,1.51 3.396,1.51 3.281,1.115 false 0.208,0.115 0.521,0.313 0.313,0.198 10 false *a 1.469,0.292 1.781,0.49 0.313,0.198 10 false 4D 4.948,0.292 5.26,0.49 0.313,0.198 10 false MB 3.677,1.427 3.99,1.625 0.313,0.198 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4D-13 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E273530
1.333,0.25 1.75,0.5 0.417,0.25 4.833,0.25 5.25,0.5 0.417,0.25 3.625,1.51 3.396,1.51 3.396,1.51 3.281,1.115 false 0.208,0.115 0.521,0.313 0.313,0.198 10 false *a 1.469,0.292 1.781,0.49 0.313,0.198 10 false 4D 4.948,0.292 5.26,0.49 0.313,0.198 10 false MB 3.677,1.427 3.99,1.625 0.313,0.198 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4D-12 - MB-1 (ILE) Always Below 1 Ω
4D-13 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY