Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › SFI SYSTEM
RM3160E _51 Engine / Hybrid System _019671 1AR-FE ENGINE CONTROL _0103543 SFI SYSTEM J

1AR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424E33
4.375,1.073 6.198,1.25 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,1.927 6.365,2.344 1.01,0.417 10 false Microprocessor 1.344,1.365 2.813,1.51 1.469,0.146 10 false from EFI NO. 2 Fuse 1.344,1.031 2.688,1.198 1.344,0.167 10 false from EFI NO. 1 Fuse 2.906,0.896 3.427,1.115 0.521,0.219 10 false BATT 0.167,1.99 2.604,2.531 2.438,0.542 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.156,2.948 2.573,3.365 2.417,0.417 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature, etc. 4.073,2.823 4.333,3.031 0.26,0.208 10 false R 2.875,1.25 3.802,1.448 0.927,0.198 10 false +B, +B2 3.167,2.219 3.458,2.448 0.292,0.229 10 false VC 4.885,0.354 5.333,0.583 0.448,0.229 10 false ECM

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

A257571E09
0.229,0.865 0.542,1.104 0.313,0.24 10 false C19 0.229,1.031 1.885,1.385 1.656,0.354 10 false Camshaft Position Sensor (for Intake Camshaft) 2.906,0.802 3.031,0.979 0.125,0.177 10 false 3 2.906,1.208 3.031,1.385 0.125,0.177 10 false 1 2.906,1.625 3.031,1.802 0.125,0.177 10 false 2 2.573,0.885 2.802,1.052 0.229,0.167 10 false VC 2.479,1.302 2.813,1.458 0.333,0.156 10 false VVI+ 2.49,1.729 2.792,1.885 0.302,0.156 10 false VVI- 0.229,2.49 0.531,2.729 0.302,0.24 10 false C20 0.229,2.656 1.885,3 1.656,0.344 10 false Camshaft Position Sensor (for Exhaust Camshaft) 2.906,2.427 3.031,2.604 0.125,0.177 10 false 3 2.906,2.833 3.031,3.01 0.125,0.177 10 false 1 2.906,3.26 3.031,3.438 0.125,0.177 10 false 2 2.49,2.51 2.802,2.677 0.313,0.167 10 false VC2 2.417,2.927 2.813,3.083 0.396,0.156 10 false VVE+ 2.438,3.354 2.792,3.51 0.354,0.156 10 false VVE- 0.24,4.135 0.573,4.406 0.333,0.271 10 false Z4 0.229,4.292 2.24,4.76 2.01,0.469 10 false Intake Air Control Valve Actuator (for Tumble Control Valve) 2.906,4.052 3.031,4.229 0.125,0.177 10 false 3 2.906,4.458 3.031,4.635 0.125,0.177 10 false 1 2.906,4.885 3.031,5.063 0.125,0.177 10 false 2 2.479,4.135 2.802,4.302 0.323,0.167 10 false VDD 2.479,4.552 2.792,4.708 0.313,0.156 10 false OUT 2.479,4.979 2.813,5.135 0.333,0.156 10 false GND 5.333,0.74 5.594,0.896 0.26,0.156 10 false 113 5.354,0.906 5.646,1.104 0.292,0.198 10 false C1 5.344,1.313 5.677,1.542 0.333,0.229 10 false C1 5.344,1.729 5.656,2.01 0.313,0.281 10 false C1 5.344,2.521 5.646,2.75 0.302,0.229 10 false C1 5.344,2.938 5.677,3.198 0.333,0.26 10 false C1 5.344,3.354 5.677,3.625 0.333,0.271 10 false C1 5.333,4.146 5.698,4.365 0.365,0.219 10 false C1 5.333,4.552 5.677,4.802 0.344,0.25 10 false C1 5.333,4.969 5.667,5.229 0.333,0.26 10 false C1 5.667,0.802 6.063,0.958 0.396,0.156 10 false VCV1 5.365,1.146 5.563,1.302 0.198,0.156 10 false 82 5.667,1.313 6.031,1.469 0.365,0.156 10 false VV1+ 5.323,1.583 5.594,1.74 0.271,0.156 10 false 114 5.667,1.635 5.99,1.792 0.323,0.156 10 false VV1- 5.323,2.365 5.583,2.521 0.26,0.156 10 false 111 5.667,2.427 6.063,2.583 0.396,0.156 10 false VCE1 5.365,2.771 5.563,2.927 0.198,0.156 10 false 81 5.667,2.938 6.052,3.094 0.385,0.156 10 false EV1+ 5.313,3.198 5.583,3.354 0.271,0.156 10 false 112 5.667,3.26 6.031,3.417 0.365,0.156 10 false EV1- 5.313,3.99 5.583,4.146 0.271,0.156 10 false 130 5.667,4.052 6.125,4.208 0.458,0.156 10 false VCIA 5.323,4.396 5.594,4.552 0.271,0.156 10 false 131 5.667,4.563 6.031,4.719 0.365,0.156 10 false IAC1 5.313,4.823 5.583,4.979 0.271,0.156 10 false 129 5.667,4.885 6.01,5.042 0.344,0.156 10 false EIA1 6.031,6.5 6.385,6.667 0.354,0.167 10 false ECM 6.177,0.448 6.635,0.646 0.458,0.198 10 false 5 V

A255263E22
6.125,5.146 6.469,5.302 0.344,0.156 10 false ECM 5.344,0.865 5.771,1.135 0.427,0.271 10 false 125 5.667,0.927 6.188,1.229 0.521,0.302 10 false VCTA 5.365,1.01 5.792,1.354 0.427,0.344 10 false C1 5.333,1.219 5.729,1.5 0.396,0.281 10 false 127 5.354,1.375 5.719,1.635 0.365,0.26 10 false C1 5.333,1.594 5.594,1.75 0.26,0.156 10 false 128 5.354,1.74 5.708,1.927 0.354,0.188 10 false C1 5.365,2.104 5.792,2.302 0.427,0.198 10 false C1 5.333,1.958 5.583,2.115 0.25,0.156 10 false 126 5.667,1.385 6.052,1.531 0.385,0.146 10 false VTA1 5.667,1.75 6.052,1.896 0.385,0.146 10 false VTA2 5.667,2.031 5.979,2.177 0.313,0.146 10 false ETA 5.375,2.385 5.677,2.667 0.302,0.281 10 false 53 5.333,2.542 5.667,2.76 0.333,0.219 10 false A43 5.333,2.896 5.906,3.177 0.573,0.281 10 false A43 5.333,3.26 5.729,3.469 0.396,0.208 10 false A43 5.333,3.656 5.802,3.896 0.469,0.24 10 false A43 5.333,4.021 5.979,4.302 0.646,0.281 10 false A43 5.333,4.385 5.854,4.729 0.521,0.344 10 false A43 5.385,2.75 5.833,2.979 0.448,0.229 10 false 56 5.385,3.115 5.719,3.302 0.333,0.188 10 false 51 5.385,3.5 5.771,3.75 0.385,0.25 10 false 54 5.375,3.875 5.729,4.115 0.354,0.24 10 false 52 5.385,4.24 5.688,4.521 0.302,0.281 10 false 55 5.667,2.458 6.073,2.615 0.406,0.156 10 false VCPA 5.667,3.281 5.979,3.438 0.313,0.156 10 false VPA 5.667,3.938 5.979,4.094 0.313,0.156 10 false EPA 5.667,3.667 6.042,3.823 0.375,0.156 10 false VPA2 5.667,4.313 6.115,4.552 0.448,0.24 10 false EPA2 5.667,2.833 6.073,2.99 0.406,0.156 10 false VCP2 0.25,1.167 0.948,1.448 0.698,0.281 10 false C41 0.25,1.344 1.771,1.906 1.521,0.563 10 false Throttle Body with Motor Assembly 2.594,1.021 3.115,1.26 0.521,0.24 10 false VC 2.521,1.375 2.833,1.531 0.313,0.156 10 false VTA 2.448,1.74 2.958,2.052 0.51,0.313 10 false VTA2 2.625,2.104 2.844,2.271 0.219,0.167 10 false E2 2.938,0.927 3.052,1.083 0.115,0.156 10 false 5 2.938,1.292 3.052,1.448 0.115,0.156 10 false 6 2.938,1.656 3.052,1.813 0.115,0.156 10 false 4 2.938,2.021 3.052,2.177 0.115,0.156 10 false 3 0.25,2.688 0.708,3.01 0.458,0.323 10 false A53 0.25,2.865 1.385,3.479 1.135,0.615 10 false Accelerator Pedal Sensor Assembly 2.438,2.552 3,2.792 0.563,0.24 10 false VCPA 2.438,2.927 2.854,3.073 0.417,0.146 10 false VCP2 2.521,3.292 2.896,3.458 0.375,0.167 10 false VPA 2.448,3.667 2.969,3.896 0.521,0.229 10 false VPA2 2.531,4.031 3,4.271 0.469,0.24 10 false EPA 2.448,4.375 3.083,4.646 0.635,0.271 10 false EPA2 2.938,2.458 3.052,2.615 0.115,0.156 10 false 4 2.938,2.833 3.052,2.99 0.115,0.156 10 false 1 2.938,3.188 3.052,3.344 0.115,0.156 10 false 6 2.938,3.594 3.052,3.75 0.115,0.156 10 false 3 2.938,3.948 3.052,4.104 0.115,0.156 10 false 5 2.938,4.313 3.052,4.469 0.115,0.156 10 false 2 6.146,0.583 6.604,0.781 0.458,0.198 10 false 5 V

PROCEDURE

1.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 2 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 2 FUSE VOLTAGE
A390147C03
0.896,2.802 1.375,2.083 false 0.167,0.094 0.479,0.385 0.313,0.292 10 false *1 0.792,2.844 1.052,3.083 0.26,0.24 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 EFI NO. 2 Fuse


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 2 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the No. 1 engine room relay block and No. 1 junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

GO TO ECM POWER SOURCE CIRCUIT

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE))
a.

Disconnect the intake air control valve actuator (for tumble control valve) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)

B

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK HARNESS AND CONNECTOR

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

8.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the intake air control valve actuator (for tumble control valve) connector.


d.

Disconnect the camshaft position sensor (for intake camshaft) connector.


e.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


f.

Disconnect the ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-125 (VCTA) - Body ground Always 10 kΩ or higher
A43-53 (VCPA) - Body ground Always 10 kΩ or higher
A43-56 (VCP2) - Body ground Always 10 kΩ or higher
C1-130 (VCIA) - Body ground Always 10 kΩ or higher
C1-111 (VCE1) - Body ground Always 10 kΩ or higher
C1-113 (VCV1) - Body ground Always 10 kΩ or higher
2 (EFI No. 2 fuse) - A43-2 (+B) Always Below 1 Ω
2 (EFI No. 2 fuse) - A43-3 (+B2) Always Below 1 Ω
A43-2 (+B) - Body ground Always 10 kΩ or higher
A43-3 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR