The power window regulator motor assemblies are operated by the power window regulator master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies. The power window regulator motor assemblies have motor, regulator and ECU functions.
This DTC is output when the ECU built into a power window regulator motor assembly and power window regulator master switch assembly determine that the power window regulator master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly is stuck.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Power window regulator master switch assembly stuck ·
Power window regulator master switch assembly held in same position for more than 20 seconds |
Power window regulator master switch assembly |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Power window regulator master switch assembly stuck ·
Power window regulator master switch assembly held in same position for more than 20 seconds |
·
Power window regulator master switch assembly ·
Power window regulator motor assembly (for driver door) ·
Wire harness or connector |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Power window regulator switch assembly stuck ·
Power window regulator switch assembly held in same position for more than 20 seconds |
·
Power window regulator switch assembly ·
Power window regulator motor assembly (for front passenger door) ·
Wire harness or connector |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Rear power window regulator switch assembly (for LH door) stuck ·
Rear power window regulator switch assembly (for LH door) held in same position for more than 20 seconds |
·
Rear power window regulator switch assembly (for LH door) ·
Power window regulator motor assembly (for rear LH door) ·
Wire harness or connector |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2312 | Power Window Switch Malfunction | ·
Rear power window regulator switch assembly (for RH door) stuck ·
Rear power window regulator switch assembly (for RH door) held in same position for more than 20 seconds |
·
Rear power window regulator switch assembly (for RH door) ·
Power window regulator motor assembly (for rear RH door) ·
Wire harness or connector |
DTC B2312 is stored in the power window regulator master switch assembly and in each power window regulator motor assembly.
If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.
Inspect the fuses for circuits related to this system before performing the following procedure.
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: for LHD
If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.
Clear the DTCs.
Check for DTCs.
DTC B2312 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the parts which the DTCs have been output from.
| Result | Proceed to |
|---|---|
| DTC output from power window regulator master switch assembly | A |
| DTC output from power window regulator motor assembly (for driver door) | B |
| DTC output from power window regulator motor assembly (for front passenger door) | C |
| DTC output from power window regulator motor assembly (for rear LH door) | D |
| DTC output from power window regulator motor assembly (for rear RH door) | E |
A
B
C
D
E
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / D-Door Motor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I7*1 or H7*2 power window regulator master switch assembly connector.
Disconnect the I4*1 or H4*2 power window regulator motor assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-20 (UP) - Body ground | Always | 10 kΩ or higher |
| I7-15 (DOWN) - Body ground | Always | 10 kΩ or higher |
| I4-10 (UP) - Body ground | Always | 10 kΩ or higher |
| I4-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H7-20 (UP) - Body ground | Always | 10 kΩ or higher |
| H7-15 (DOWN) - Body ground | Always | 10 kΩ or higher |
| H4-10 (UP) - Body ground | Always | 10 kΩ or higher |
| H4-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
DTC B2312 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / P-Door Motor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P Door P/W Auto SW | Front passenger door power window auto switch signal | OFF or ON | OFF: Front passenger door power window auto switch not being operated
ON: Front passenger door power window auto switch being operated |
- |
| P Door P/W Up SW | Front passenger door power window manual up switch signal | OFF or ON | OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated |
- |
| P Door P/W Down SW | Front passenger door power window manual down switch signal | OFF or ON | OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated |
- |
| Tester Display |
|---|
| P Door P/W Auto SW |
| P Door P/W Up SW |
| P Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power window regulator switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL
Inspect the power window regulator switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H5*1 or I5*2 power window regulator motor assembly (for front passenger door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H8-5 (UP) - Body ground | Always | 10 kΩ or higher |
| H8-4 (DOWN) - Body ground | Always | 10 kΩ or higher |
| H8-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
| H5-10 (UP) - Body ground | Always | 10 kΩ or higher |
| H5-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| H5-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I8-5 (UP) - Body ground | Always | 10 kΩ or higher |
| I8-4 (DOWN) - Body ground | Always | 10 kΩ or higher |
| I8-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
| I5-10 (UP) - Body ground | Always | 10 kΩ or higher |
| I5-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| I5-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / RL-Door Motor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Door P/W Auto SW | Rear LH door power window auto switch signal | OFF or ON | OFF: Rear LH door power window auto switch not being operated
ON: Rear LH door power window auto switch being operated |
- |
| RL Door P/W Up SW | Rear LH door power window manual up switch signal | OFF or ON | OFF: Rear LH door power window manual up switch not being operated
ON: Rear LH door power window manual up switch being operated |
- |
| RL Door P/W Down SW | Rear LH door power window manual down switch signal | OFF or ON | OFF: Rear LH door power window manual down switch not being operated
ON: Rear LH door power window manual down switch being operated |
- |
| Tester Display |
|---|
| RL Door P/W Auto SW |
| RL Door P/W Up SW |
| RL Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear power window regulator switch assembly (for LH door).
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL
Inspect the rear power window regulator switch assembly (for LH door).
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 power window regulator motor assembly (for rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K6-5 (UP) - Body ground | Always | 10 kΩ or higher |
| K6-4 (DOWN) - Body ground | Always | 10 kΩ or higher |
| K6-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
| K2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| K2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| K2-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / RR-Door Motor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door P/W Auto SW | Rear RH door power window auto switch signal | OFF or ON | OFF: Rear RH door power window auto switch not being operated
ON: Rear RH door power window auto switch being operated |
- |
| RR Door P/W Up SW | Rear RH door power window manual up switch signal | OFF or ON | OFF: Rear RH door power window manual up switch not being operated
ON: Rear RH door power window manual up switch being operated |
- |
| RR Door P/W Down SW | Rear RH door power window manual down switch signal | OFF or ON | OFF: Rear RH door power window manual down switch not being operated
ON: Rear RH door power window manual down switch being operated |
- |
| Tester Display |
|---|
| RR Door P/W Auto SW |
| RR Door P/W Up SW |
| RR Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear power window regulator switch assembly (for RH door).
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL
Inspect the rear power window regulator switch assembly (for RH door).
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J2 power window regulator motor assembly (for rear RH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J6-5 (UP) - Body ground | Always | 10 kΩ or higher |
| J6-4 (DOWN) - Body ground | Always | 10 kΩ or higher |
| J6-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
| J2-10 (UP) - Body ground | Always | 10 kΩ or higher |
| J2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| J2-4 (AUTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG