The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
The parking brake is applied.
EBD operation is not possible.
The brake booster assembly is judged to be defective.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin (w/ smart entry and start system).
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Battery | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1AR-FE: Click herePower Source / Network>1AR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2GR-FE: Click herePower Source / Network>2GR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the A47 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| A47-34 (IG1) - A47-1 (GND1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-1 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A47 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Parking Brake SW | Parking brake switch assembly | ON or OFF | ON: Parking brake depressed
OFF: Parking brake released |
- |
| Tester Display |
|---|
| Parking Brake SW |
Using the GTS, check that the switch condition displayed on the GTS changes according to the parking brake operation.
The GTS displays ON or OFF according to parking brake operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly)) |
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the A51 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position changes according to the brake fluid level.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (E) | Switch OFF (Float up) | 1.9 to 2.1 kΩ |
| 1 (+) - 2 (E) | Switch ON (Float down) | Below 1 Ω |
If the switch condition is normal, adjust the brake fluid level to the MAX level.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>DISASSEMBLY
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for RHD)>DISASSEMBLY
Disconnect the F22 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F22-9 (B/LE) - A51-1 (+) | Always | Below 1 Ω |
| F22-9 (B/LE) or A51-1 (+) - Body ground | Always | 10 kΩ or higher |
| A51-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A51 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.
Reconnect the F22 combination meter assembly connector.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Warning Light | Brake warning light | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Tester Display |
|---|
| Brake Warning Light |
Check the GTS display condition of the brake warning light.
| Result | Proceed to |
|---|---|
| Display of the Data List remains ON. | A |
| Display of the Data List remains OFF. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| *a | Component without harness connected
(Parking Brake Switch Assembly) |
Turn the ignition switch off.
Disconnect the A58 parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - Body ground | Switch ON
(Switch pin free) |
Below 1 Ω |
| 1 (+) - Body ground | Switch OFF
(Switch pin pushed in) |
10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for LHD)>REMOVAL
for RHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for RHD)>REMOVAL
Disconnect the 4F instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-28 - A58-1 (+) | Always | Below 1 Ω |
| 4F-28 or A58-1 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-28 - 12 (PKB) | Always | Below 1 Ω |
| 4F-28 or 12 (PKB) - Body ground | Always | 10 kΩ or higher |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG