Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL(for LH Side) › 2013.12–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107344 DIFFERENTIAL OIL SEAL(for LH Side) A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for LH Side)  REPLACEMENT  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53876A 2.SEPARATE FRONT FENDER LINER LH

Hide 53737B 3.REMOVE FRONT FENDER APRON SEAL LH

Hide 4.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly.


b.
C239660

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.


c.
C201684C20
1.208,2.677 0.833,2.677 false 0.604,3.927 0.417,3.927 0.417,3.927 0.708,3.125 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *a 0.656,3.844 0.833,4.031 0.177,0.188 10 false *b
*1 No. 1 Transmission Oil Filler Tube
*a Hexagon Socket Wrench
*b Overflow Plug Hole


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.

Drain automatic transaxle fluid from the automatic transaxle assembly.


e.
C201684C21
1.208,2.677 0.833,2.677 false 0.604,3.927 0.417,3.927 0.417,3.927 0.708,3.125 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *a 0.656,3.844 0.833,4.031 0.177,0.188 10 false *b
*1 No. 1 Transmission Oil Filler Tube
*a Hexagon Socket Wrench
*b Overflow Plug Hole


Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


f.
C239660

Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



g.
C201682

Temporarily install the gasket and refill plug to the automatic transaxle assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 43420H 6.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

C201712N02
0.708,2.896 0.708,3.031 false 0.802,1.833 0.896,1.833 0.896,1.833 1.219,1.458 false 0.583,3.052 0.896,3.219 0.313,0.167 10 SST 0.521,1.771 0.833,1.938 0.313,0.167 10 SST

a.

Using SST, remove the transaxle case oil seal LH from the automatic transaxle assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle case sub-assembly.



Hide 43420H 7.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C201714N02
0.479,0.458 0.656,0.458 0.656,0.458 0.615,0.563 false 0.573,0.458 0.313,0.958 false 2.083,2.052 2.646,2.708 2.646,2.708 2.49,2.031 false 0.208,0.375 0.531,0.542 0.323,0.167 10 SST 2.542,2.729 2.865,2.896 0.323,0.167 10 SST

Using SST and a hammer, install a new transaxle case oil seal LH to the automatic transaxle assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)


NOTICE:
·

Make sure that the transaxle case oil seal LH is installed in the correct direction.

·

Do not damage the transaxle case oil seal LH lip.




b.

Coat the lip of the transaxle case oil seal LH with MP grease.


Hide 53737B 10.INSTALL FRONT FENDER APRON SEAL LH

Hide 53876A 11.INSTALL FRONT FENDER LINER LH

Hide 51441 12.INSTALL NO. 1 ENGINE UNDER COVER