Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL(for RHD)
RM3160E _54 Brake _019696 PARKING BRAKE _0108000 PARKING BRAKE PEDAL(for RHD) A

PARKING BRAKE  PARKING BRAKE PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 46200 1.INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY

a.

Install the parking brake control pedal assembly to the body with the 3 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the parking brake switch connector.


c.

Insert the No. 1 parking brake cable assembly toward the outside of the cabin.


d.
C294849

Engage the clamp.


e.

Install the No. 1 parking brake cable assembly to the body with the 2 bolts and 3 nuts.

Torque:
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


f.
C294844C01
2.583,1.021 2.031,1.021 2.031,1.021 1.719,0.635 true 1.823,0.552 2.021,0.396 2.021,0.396 2.583,0.396 true 2.615,0.927 2.813,1.094 0.198,0.167 10 true *1 2.615,0.313 2.823,0.49 0.208,0.177 10 true *2
*1 Lock Nut
*2 No. 1 Wire Adjusting Nut


Temporarily install the lock nut.

HINT:

After adjusting parking brake pedal travel, tighten the lock nut.



Hide 46341 2.INSTALL PARKING BRAKE EQUALIZER

a.
C165689

Install the parking brake equalizer to the No. 1 parking brake cable assembly as shown in the illustration.


b.
C296927C01
1.333,1.448 1.667,1.813 1.667,1.813 1.208,1.813 true 1.042,1.719 1.354,1.875 0.313,0.156 10 false *a
*a Groove


Slide the rubber boot back as shown in the illustration.

NOTICE:

Securely fit the protrusion on the rubber boot into the No. 1 parking brake cable assembly groove.



Hide 46430 3.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 3 parking brake cable assembly to the parking brake equalizer.


Hide 46420 4.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Perform the same procedure as for the No. 3 parking brake cable assembly.


Hide 5.INSPECT PARKING BRAKE PEDAL TRAVEL

Hide 6.ADJUST PARKING BRAKE PEDAL TRAVEL

Hide 58730 7.INSTALL REAR ENGINE SERVICE COVER ASSEMBLY

a.

Install the rear engine service cover assembly to the body with the 2 bolts.


Hide 58167A 8.INSTALL FRONT CENTER FLOOR COVER

a.
C293697C01
0,0 0,0 false
V100135

Nut
V100136

Screw


Engage the 4 clips and install the front center floor cover.


b.

Install the nut and 2 screws.


Hide 58166 9.INSTALL FRONT FLOOR COVER LH

a.
C293695C01
1.896,1.24 2.5,1.24 true 1.25,1.906 0.771,1.635 0.771,1.635 1.406,1.292 true 2.531,1.156 2.688,1.354 0.156,0.198 10 true A 0.635,1.552 0.76,1.75 0.125,0.198 10 true B
V100135

Bolt
V100136

Screw


Engage the 2 clips (B) to install the front floor cover LH.


b.

Install the 4 bolts, 2 screws and clip (A).


Hide 58563Q 10.INSTALL FRONT NO. 3 FLOOR SILENCER

a.

Install the front No. 3 floor silencer to the original position.


Hide 55215A 11.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
C302354

Engage the 2 clips to install the No. 3 dash panel insulator pad.


Hide 58817A 14.INSTALL FRONT NO. 2 CONSOLE BOX INSERT

Hide 58510D 15.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Engage the 3 floor carpet hooks to install the front floor carpet assembly.


Hide 73220 16.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 17.INSTALL LOWER CENTER PILLAR GARNISH LH

Hide 18.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918A 19.INSTALL REAR DOOR SCUFF PLATE LH

Hide 72138M 20.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH

Hide 21.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 58810J 22.INSTALL CONSOLE BOX ASSEMBLY

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION


Hide 73900 23.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 24.INSTALL FRONT SEAT ASSEMBLY LH

HINT:

Use the same procedure as for LHD.

for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION

for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION


Hide 25.INSPECT BRAKE WARNING LIGHT