Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2013.12–2015.11
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0108188 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284D 3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B362068

Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.


Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.
B362070

Using a moulding remover, disengage the 2 clips, 2 claws and 2 guides.


b.

Disconnect the connector and remove the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 67488C 5.REMOVE REAR DOOR REAR GUIDE SEAL

a.
B362072

Disengage the 3 clips and claw to remove the rear door rear guide seal.


Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B362073C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape around the rear door panel.


b.
B362074C01
1.271,1.5 1.635,1.115 true 1.125,1.51 1.438,1.667 0.313,0.156 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw and open the cover.


c.
B362076

Remove the 3 screws.


d.
B362077

Disengage the 9 clips and claw, and remove the rear door trim board sub-assembly as shown in the illustration.


e.

w/ Illumination:

i.

Disconnect the connector.



f.
B362079

Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


Hide 69206C 7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B362081

Disengage the 2 claws and guide, and remove the rear door inside handle sub-assembly.


Hide 86160B 8.REMOVE REAR SPEAKER ASSEMBLY

Hide 68174A 9.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

a.
B362082

Disengage the 7 claws and remove the rear door inner glass weatherstrip as shown in the illustration.


Hide 65908D 10.REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B362085

Remove the 7 screws.


b.

Disengage the 3 guides and remove the rear curtain sub-assembly.


Hide 67842E 11.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B362086

Disconnect the 2 connectors.


b.

Disengage the 2 clamps and remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 67858B 12.REMOVE REAR DOOR PANEL PROTECTOR

a.
B362088

Disengage the clip, claw and 2 guides, and remove the rear door panel protector.


Hide 68640A 13.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B362089C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and rear door check assembly.


Hide 67872 14.REMOVE REAR DOOR WEATHERSTRIP

a.
B362090

Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.


Hide 68152C 15.REMOVE REAR DOOR GLASS RUN

a.
B362091

Remove the rear door glass run.


Hide 67408E 16.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B362092C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Screw


Remove the 2 bolts and nut.


b.

Remove the screw and rear door window division bar sub-assembly.


Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.
B362093

Remove the grommet.


b.

Connect the cable to the negative (-) battery terminal.


c.

Connect the rear power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.


e.

Disconnect the rear power window regulator switch assembly.


f.
B362094

Remove the 2 bolts.

NOTICE:

Do not damage the rear door glass sub-assembly.



g.
B362095

Remove the rear door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



Hide 18.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

a.
B362097C01
2.01,0.76 2.26,0.635 true 1.813,0.667 2.042,0.823 0.229,0.156 10 true *a
*a Temporary Bolt


Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.



b.

Remove the 5 bolts.


c.

Remove the rear door window regulator assembly.


d.

Remove the temporary bolt from the rear door window regulator assembly.


Hide 85720E 19.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B362099

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.


Hide 69060A 20.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

a.
B362100C01
2.458,2.75 2.729,2.76 true 2.74,2.667 3.01,2.823 0.271,0.156 10 true *a
*a Release Plate


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly and remove the rear door lock with motor assembly.


c.

When reusing the rear door lock with motor assembly:

i.
B362102

Remove the door lock wiring harness seal from the rear door lock with motor assembly.



Hide 69740D 21.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B362103

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B362105

Remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69780B 22.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B362107

Remove the rear door inside locking cable assembly as shown in the illustration.


Hide 69227M 23.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B362109

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.



b.

Disengage the claw and remove the rear door outside handle cover.


Hide 69240 24.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B362110

Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

NOTICE:

The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless it is pulled and held.



b.
B362111

Remove the rear door outside handle assembly as shown in the illustration.


Hide 69241G 25.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B362113

Disengage the 3 claws and remove the rear door front outside handle pad.


Hide 69242G 26.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B362114

Disengage the 2 claws and remove the rear door rear outside handle pad.


Hide 69204A 27.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B362115C01
0.083,0.083 0.417,0.333 0.333,0.25 12 true *A 0.104,2.01 0.417,2.25 0.313,0.24 12 true *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, loosen the screw.


b.

Slide the rear door outside handle frame sub-assembly to disengage the claw, and then remove it.


Hide 67673A 28.REMOVE REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)

a.
B362118

Disengage the 3 claws and remove the rear door frame garnish.


Hide 67674A 29.REMOVE REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)

a.
B362119

Disengage the 3 claws and remove the rear door frame garnish.


Hide 67003C 30.REMOVE REAR DOOR PANEL CUSHION

a.
B362120

Disengage the 2 claws and remove the 2 rear door panel cushions.


Hide 67847F 31.REMOVE REAR DOOR VENT SEAL

a.
B362121
1.208,0.365 1.365,0.563 0.156,0.198 10 true A 1.177,1.24 1.333,1.438 0.156,0.198 10 true A 1.146,2.229 1.604,2.427 0.458,0.198 10 false A-A
V100155

Double-sided Tape


Remove the rear door vent seal.


Hide 67859B 32.REMOVE REAR DOOR LOWER HOLE COVER

a.
B362122N01
1.698,0.156 1.854,0.354 0.156,0.198 10 true A 1.719,1.25 1.875,1.448 0.156,0.198 10 true A 1.188,2.271 1.646,2.469 0.458,0.198 10 false A-A

Remove the rear door lower hole cover.


Hide 75740 33.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 75762A 34.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75766A 35.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75764A 36.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75744 37.REMOVE REAR DOOR REAR UPPER OUTSIDE MOULDING

Hide 67896 38.REMOVE REAR DOOR NO. 3 WEATHERSTRIP

a.
B362129C01
0,0 0,0 false
V100155

Double-sided Tape


Disengage the claw and remove the rear door No. 3 weatherstrip.


Hide 75952A 39.REMOVE FRONT INNER BLACK OUT TAPE

Hide 75954A 40.REMOVE REAR INNER BLACK OUT TAPE

Hide 75938 41.REMOVE UPPER INNER BLACK OUT TAPE

Hide 75078 42.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75392A 43.REMOVE NO. 1 OUTSIDE MOULDING RETAINER

a.
B362125

Disengage the 2 clips as shown in the illustration.


b.
B362126

Disengage the 2 clips and remove the 2 No. 1 outside moulding retainers.


Hide 75392E 44.REMOVE NO. 1 OUTSIDE MOULDING RETAINER

a.
B362127

Remove the screw.


b.
B362128

Disengage the clip and remove the No. 1 outside moulding retainer.


Hide 67888A 45.REMOVE REAR DOOR NO. 2 WEATHERSTRIP

a.
B362123

Using a clip remover, disengage the 6 clips and remove the rear door No. 2 weatherstrip.


Hide 46.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75797 47.REMOVE REAR DOOR UPPER OUTSIDE MOULDING PAD