Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
75797
2.INSTALL REAR DOOR UPPER OUTSIDE MOULDING PAD
3.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY
67888A
4.INSTALL REAR DOOR NO. 2 WEATHERSTRIP
Engage the 6 clips to install the rear door No. 2 weatherstrip.
75392E
5.INSTALL NO. 1 OUTSIDE MOULDING RETAINER
Engage the clip to install the No. 1 outside moulding retainer.
Install the screw.
75392A
6.INSTALL NO. 1 OUTSIDE MOULDING RETAINER
Engage the 2 clips to install the 2 No. 1 outside moulding retainers.
Engage the 2 clips as shown in the illustration.
75078
7.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY
8. REPAIR INSTRUCTION
75938
9.INSTALL UPPER INNER BLACK OUT TAPE
75954A
10.INSTALL REAR INNER BLACK OUT TAPE
75952A
11.INSTALL FRONT INNER BLACK OUT TAPE
67896
12.INSTALL REAR DOOR NO. 3 WEATHERSTRIP
Clean the rear door panel.
|
Double-sided Tape |
Engage the claw and install a new rear door No. 3 weatherstrip.
75744
13.INSTALL REAR DOOR REAR UPPER OUTSIDE MOULDING
75764A
14.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING
75766A
15.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING
75762A
16.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING
75740
17.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
67859B
18.INSTALL REAR DOOR LOWER HOLE COVER
Install the rear door lower hole cover as shown in the illustration.
67847F
19.INSTALL REAR DOOR VENT SEAL
Clean the rear door panel.
|
Double-sided Tape |
Install a new rear door vent seal as shown in the illustration.
67003C
20.INSTALL REAR DOOR PANEL CUSHION
Engage the 2 claws to install 2 new rear door panel cushions.
67673A
21.INSTALL REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)
Engage the 3 claws to install the rear door frame garnish.
67674A
22.INSTALL REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)
Engage the 3 claws to install the rear door frame garnish.
69204A
23.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
| *A | Outside |
| *B | Inside |
Engage the claw.
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.
69242G
24.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD
Engage the 2 claws to install the rear door rear outside handle pad.
69241G
25.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the rear door front outside handle pad.
69240
26.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Insert the front end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly.
If the release plate of the rear door outside handle frame sub-assembly is not pulled and held when installing the rear door outside handle assembly, it will interfere with the rear door outside handle assembly and will be damaged.
Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly, then slide the rear door outside handle assembly toward the front of the vehicle to install it.
69227M
27.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claw.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.
69780B
28.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
Install the rear door inside locking cable assembly as shown in the illustration.
69740D
29.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Install the rear door lock remote control cable assembly as shown in the illustration.
Engage the 2 claws as shown in the illustration.
69060A
30.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY
When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.
Apply MP grease to the sliding parts of the rear door lock with motor assembly.
When reusing the rear door lock with motor assembly:
Install a new door lock wiring harness seal to the rear door lock with motor assembly.
| *a | Release Plate |
Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.
Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.
85720E
31.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.
Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.
32.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Temporary install the temporary bolt to the rear door window regulator assembly.
| *a | Temporary Bolt |
Temporarily install the rear door window regulator assembly with the 5 bolts.
Tighten the temporary bolt and 5 bolts to install the rear door window regulator assembly.
Tighten the bolts in the order shown in the illustration.
68104
33.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Connect the cable to the negative (-) battery terminal.
Connect the rear power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the rear power window regulator switch assembly.
Disconnect the cable from the negative (-) battery terminal.
Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.
Install the rear door glass sub-assembly with the 2 bolts.
Install the grommet.
67408E
34.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
|
Bolt |
|
Nut |
|
Screw |
Install the 2 bolts.
Install the rear door lower window division bar sub-assembly with the nut and screw.
68152C
35.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
67872
36.INSTALL REAR DOOR WEATHERSTRIP
Engage the 20 clips to install the rear door weatherstrip.
68640A
37.INSTALL REAR DOOR CHECK ASSEMBLY
Apply MP grease to the sliding parts of the rear door check assembly.
Clean the bolt hole on the vehicle body.
Clean the bolt threads of the bolt.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
|
Bolt |
|
Nut |
Install the rear door check assembly with the 2 nuts and bolt.
67858B
38.INSTALL REAR DOOR PANEL PROTECTOR
Engage the 2 guides, claw and clip to install the rear door panel protector.
67842E
39.INSTALL REAR DOOR SERVICE HOLE COVER
Apply new butyl tape to the rear door panel.
| *a | Reference Point |
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
Install the new rear door service hole cover according to the reference points on the rear door panel.
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
Engage the 2 clamps.
Connect the 2 connectors.
65908D
40.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)
Engage the 3 guides.
Install the rear curtain sub-assembly with the 7 screws.
68174A
41.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Engage the 7 claws to install the rear door inner glass weatherstrip as shown in the illustration.
86160B
42.INSTALL REAR SPEAKER ASSEMBLY
69206C
43.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
67604
44.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
w/ Illumination:
Connect the connector.
Engage the claw and 9 clips to install the rear door trim board sub-assembly.
Install the 3 screws.
Engage the claw to close the cover.
67488C
45.INSTALL REAR DOOR REAR GUIDE SEAL
Engage the 3 clips and claw to install the rear door rear guide seal.
46.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Connect the connector.
Engage the 2 guides, 2 claws and 2 clips to install the rear power window regulator switch assembly with rear door upper armrest base panel.
69284D
47.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
Engage the 3 claws to install the rear door inside handle bezel plug.
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
49. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)
50.INSPECT POWER WINDOW OPERATION
for Models with Jam Protection Function on 4 Windows:
for Models with Jam Protection Function on Front Door Windows: