Home › Engine / Hybrid System › 2GR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019666 2GR-FE INTAKE / EXHAUST _0109813 EXHAUST MANIFOLD A

2GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


PROCEDURE

Hide 16400 1.REMOVE RADIATOR ASSEMBLY

Hide 51442 2.REMOVE NO. 2 ENGINE UNDER COVER

Hide 58166 3.REMOVE FRONT FLOOR COVER LH

a.
A315837C01
1.521,1.313 1.74,1.542 0.219,0.229 10 true A 1.552,0.635 1.771,0.865 0.219,0.229 10 true B 0.781,0.542 1,0.771 0.219,0.229 10 true B
V100135

Bolt
V100136

Screw


Remove the clip (A), 2 screws and 4 bolts from the front floor cover LH.


b.

Disconnect the 2 clips (B) to remove the front floor cover LH.


Hide 37100 4.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

Hide 17403 5.REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

a.
A315099

Disengage the 4 wire harness clamps.


b.

Disconnect the heated oxygen sensor (for Bank 1) connector.


c.
A316013

Remove the 4 bolts, 2 nuts and 2 compression springs and front No. 3 exhaust pipe sub-assembly.


d.

Remove the 3 gaskets from the front No. 3 exhaust pipe sub-assembly.


Hide 17118 6.REMOVE MANIFOLD STAY

a.
A197640

Remove the bolt, nut and manifold stay from the exhaust manifold sub-assembly RH (TWC: Front Catalyst) and automatic transaxle assembly.


Hide 17104 7.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst)

a.
A316092

Disconnect the air fuel ratio sensor (for Bank 1) connector.


b.

Disengage the wire harness clamp.


c.
A170131

Using a 12 mm deep socket wrench, remove the 6 nuts and exhaust manifold sub-assembly RH (TWC: Front Catalyst).


Hide 17173 8.REMOVE EXHAUST MANIFOLD TO HEAD GASKET

a.
A255352

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17584B 9.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

a.
A316019

Remove the 2 bolts and No. 1 exhaust pipe support bracket.


Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY

a.
A315096

Disengage the 3 wire harness clamps.


b.

Disconnect the heated oxygen sensor (for Bank 2) connector.


c.
A316018

Remove the 2 nuts and front exhaust pipe assembly from the exhaust manifold sub-assembly LH (TWC: Front Catalyst).


d.

Remove the gasket from the front exhaust pipe assembly.


Hide 89467B 11.REMOVE AIR FUEL RATIO SENSOR (for Bank 2)

Hide 12142 12.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17168 13.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A197636

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold sub-assembly LH (TWC: Front Catalyst).


Hide 17119 14.REMOVE NO. 2 MANIFOLD STAY

a.
A140783

Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold sub-assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 17105 15.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst)

a.
A197637

Using a 12 mm deep socket wrench, remove the 6 nuts and exhaust manifold sub-assembly LH (TWC: Front Catalyst).


Hide 89467B 16.REMOVE AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17173A 17.REMOVE EXHAUST MANIFOLD TO HEAD GASKET LH

a.
A255353

Remove the exhaust manifold to head gasket LH from the cylinder head sub-assembly.