Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019711 PRE-CRASH SAFETY _0110871 PRE-CRASH SAFETY SYSTEM Y

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the pre-crash safety system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*


c.

Connect the GTS to the DLC3.


d.

Turn the GTS on.


e.

Turn the cruise control switch (ON/OFF button) on.


f.

Enter the following menus: Powertrain / Radar Cruise / Utility / Beam Axis Misalignment Reading.


g.

Check the amount of misalignment and make a note.

Powertrain > Radar Cruise > Utility
Tester Display
Beam Axis Misalignment Reading
50005 239 4260

Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

5.CHECK FOR DTC (PRE-CRASH 2)*

B

5.CHECK FOR DTC (PRE-CRASH 2)*
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

b.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTCs are not output A
DTCs are output B
DTCs are not output, and malfunction cannot be duplicated or checked C



A

6.PROBLEM SYMPTOMS TABLE

B

C

6.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.ADJUST, REPAIR OR REPLACE
7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

9.CONFIRMATION TEST
9.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END