Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2015.11
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0108188 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75797 2.INSTALL REAR DOOR UPPER OUTSIDE MOULDING PAD

Hide 3.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 67888A 4.INSTALL REAR DOOR NO. 2 WEATHERSTRIP

a.
B362123

Engage the 6 clips to install the rear door No. 2 weatherstrip.


Hide 75392E 5.INSTALL NO. 1 OUTSIDE MOULDING RETAINER

a.
B362128

Engage the clip to install the No. 1 outside moulding retainer.


b.
B362127

Install the screw.


Hide 75392A 6.INSTALL NO. 1 OUTSIDE MOULDING RETAINER

a.
B362126

Engage the 2 clips to install the 2 No. 1 outside moulding retainers.


b.
B362124

Engage the 2 clips as shown in the illustration.


Hide 75078 7.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75938 9.INSTALL UPPER INNER BLACK OUT TAPE

Hide 75954A 10.INSTALL REAR INNER BLACK OUT TAPE

Hide 75952A 11.INSTALL FRONT INNER BLACK OUT TAPE

Hide 67896 12.INSTALL REAR DOOR NO. 3 WEATHERSTRIP

a.

Clean the rear door panel.


b.
B362129C02
0,0 0,0 false
V100155

Double-sided Tape


Engage the claw and install a new rear door No. 3 weatherstrip.


Hide 75744 13.INSTALL REAR DOOR REAR UPPER OUTSIDE MOULDING

Hide 75764A 14.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75766A 15.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75762A 16.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75740 17.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 67225A 18.INSTALL UPPER QUARTER WINDOW STOP

a.

Apply soapy water to the upper quarter window stop.


b.
B426648

Install the upper quarter window stop.


c.

Wipe off any soapy water on the door.


Hide 67859B 19.INSTALL REAR DOOR LOWER HOLE COVER

a.
B362122N01
1.698,0.156 1.854,0.354 0.156,0.198 10 true A 1.719,1.25 1.875,1.448 0.156,0.198 10 true A 1.188,2.271 1.646,2.469 0.458,0.198 10 false A-A

Install the rear door lower hole cover as shown in the illustration.


Hide 67847F 20.INSTALL REAR DOOR VENT SEAL

a.
B433235N01
1.927,0.698 2.083,0.896 0.156,0.198 10 true A 1.708,1.531 1.865,1.729 0.156,0.198 10 true A 1.344,2.25 1.802,2.448 0.458,0.198 10 false A-A

Install the rear door vent seal.


Hide 67003C 21.INSTALL REAR DOOR PANEL CUSHION

a.
B362120

Engage the 2 claws to install 2 new rear door panel cushions.


Hide 67673A 22.INSTALL REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)

a.
B362118

Engage the 3 claws to install the rear door frame garnish.


Hide 67674A 23.INSTALL REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)

a.
B362119

Engage the 3 claws to install the rear door frame garnish.


Hide 69204A 24.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B362116C01
0.083,0.083 0.417,0.333 0.333,0.25 12 true *A 0.083,2.5 0.417,2.76 0.333,0.26 12 true *B
*A Outside
*B Inside


Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 25.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B362114

Engage the 2 claws to install the rear door rear outside handle pad.


Hide 69241G 26.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B362113

Engage the 3 claws to install the rear door front outside handle pad.


Hide 69240 27.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B362112

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly.

NOTICE:

If the release plate of the rear door outside handle frame sub-assembly is not pulled and held when installing the rear door outside handle assembly, it will interfere with the rear door outside handle assembly and will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly, then slide the rear door outside handle assembly toward the front of the vehicle to install it.


Hide 69227M 28.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B362109

Engage the claw.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 29.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B362108

Install the rear door inside locking cable assembly as shown in the illustration.


Hide 69740D 30.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B362106

Install the rear door lock remote control cable assembly as shown in the illustration.


b.
B362104

Engage the 2 claws as shown in the illustration.


Hide 69060A 31.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door lock with motor assembly:

i.
B362102

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B362101C01
2.469,2.75 2.75,2.76 true 2.802,2.667 3.073,2.833 0.271,0.167 10 true *a
*a Release Plate


Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.

HINT:

Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 85720E 32.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.


a.
B362099

Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.



Hide 33.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Temporary install the temporary bolt to the rear door window regulator assembly.


c.
B362097C02
2.01,0.76 2.26,0.635 true 1.813,0.667 2.042,0.823 0.229,0.156 10 true *a 0.625,0.479 0.781,0.677 0.156,0.198 10 true 1 1.438,0.427 1.594,0.625 0.156,0.198 10 true 2 2.125,1.396 2.281,1.594 0.156,0.198 10 true 3 2.688,0.094 2.844,0.292 0.156,0.198 10 true 4 2.875,1.188 3.031,1.385 0.156,0.198 10 true 5 1.875,0.271 2.031,0.469 0.156,0.198 10 true 6
*a Temporary Bolt


Temporarily install the rear door window regulator assembly with the 5 bolts.


d.

Tighten the temporary bolt and 5 bolts to install the rear door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68104 34.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the rear power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the rear power window regulator switch assembly.


d.

Disconnect the cable from the negative (-) battery terminal.


e.
B362096

Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.


f.
B362094

Install the rear door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
B362093

Install the grommet.


Hide 67408E 35.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B362092C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Screw


Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


b.

Install the rear door lower window division bar sub-assembly with the nut and screw.

Torque:
Nut : 6.2 N*m (63 kgf*cm, 55 in.*lbf)
Screw : 3.6 N*m (37 kgf*cm, 32 in.*lbf)


Hide 68152C 36.INSTALL REAR DOOR GLASS RUN

a.
B362091

Install the rear door glass run.


Hide 67872 37.INSTALL REAR DOOR WEATHERSTRIP

a.
B362090

Engage the 20 clips to install the rear door weatherstrip.


Hide 68640A 38.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.

Clean the bolt hole on the vehicle body.


c.

Clean the bolt threads of the bolt.


d.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
B362089C02
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the rear door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 27 N*m (275 kgf*cm, 20 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67858B 39.INSTALL REAR DOOR PANEL PROTECTOR

a.
B362088

Engage the 2 guides, claw and clip to install the rear door panel protector.


Hide 67842E 40.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.
B362087C01
0.406,0.26 0.542,0.313 false 2.677,0.292 2.844,0.208 false 1.76,3.219 1.875,3.26 false 0.24,0.146 0.552,0.302 0.313,0.156 10 false *a 2.865,0.115 3.177,0.271 0.313,0.156 10 false *a 1.927,3.177 2.24,3.333 0.313,0.156 10 false *a
*a Reference Point


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.


c.

Install the new rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



d.

Engage the 2 clamps.


e.

Connect the 2 connectors.


Hide 65908D 41.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B362085

Engage the 3 guides.


b.

Install the rear curtain sub-assembly with the 7 screws.


Hide 68174A 42.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

a.
B362083

Engage the 7 claws to install the rear door inner glass weatherstrip as shown in the illustration.


Hide 86160B 43.INSTALL REAR SPEAKER ASSEMBLY

Hide 69206C 44.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B362081

Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


Hide 67604 45.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B362080C01
3.094,0.677 2.688,0.354 true 3,1.427 3.229,0.938 true 2.51,0.26 2.823,0.417 0.313,0.156 10 true *1 2.906,1.458 3.219,1.615 0.313,0.156 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


b.

w/ Illumination:

i.

Connect the connector.



c.
B362078

Engage the claw and 9 clips to install the rear door trim board sub-assembly.


d.
B362076

Install the 3 screws.


e.
B362075

Engage the claw to close the cover.


Hide 67488C 46.INSTALL REAR DOOR REAR GUIDE SEAL

a.
B362072

Engage the 3 clips and claw to install the rear door rear guide seal.


Hide 47.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.

Connect the connector.


b.
B362071

Engage the 2 guides, 2 claws and 2 clips to install the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 69284D 48.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B362069

Engage the 3 claws to install the rear door inside handle bezel plug.


Hide 49.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 50. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

Hide 51.INSPECT POWER WINDOW OPERATION