Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY › 2015.11–2016.11
RM3160E _52 Drivetrain _019726 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0107346 AUTOMATIC TRANSAXLE ASSEMBLY A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C297896C01
2.198,1.01 2.292,0.542 2.292,0.542 2.51,0.542 true 1.083,1.063 0.938,0.604 0.938,0.604 0.771,0.615 true 1.24,2.063 1.021,2.073 1.021,2.073 1.104,1.635 true 2.573,0.469 2.885,0.625 0.313,0.156 10 false *a 0.573,0.552 0.885,0.708 0.313,0.156 10 false *b 1.292,1.979 1.604,2.135 0.313,0.156 10 false *b
*a Matchmark
*b Key


Turn the front oil pump drive gear so that the key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.


b.
C057914C02
1.406,1.979 1.583,1.979 1.583,1.979 1.75,1.552 false 1.698,0.344 1.302,0.167 1.302,0.167 1.177,0.167 true 1.01,0.083 1.323,0.24 0.313,0.156 10 false *a 1.229,1.917 1.542,2.073 0.313,0.156 10 false *b
*a Groove
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C343768C01
1.292,1.365 0.552,0.906 0.552,0.906 1.281,1.198 true 2.5,1.906 1.24,2.875 1.24,2.875 2.49,1.594 true 1.063,2.875 1.396,3.156 0.333,0.281 10 false *1 0.344,0.76 0.646,1 0.302,0.24 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C343769C01
0.771,0.531 0.896,0.531 0.896,0.531 1.292,1.208 true 0.635,3.01 0.76,3.01 0.76,3.01 1.292,2.229 true 2.51,1.604 1.552,2.896 1.552,2.896 2.542,1.927 true 1.427,2.917 1.729,3.188 0.302,0.271 10 false *1 0.427,2.885 0.75,3.156 0.323,0.271 10 false *a 0.552,0.417 0.865,0.646 0.313,0.229 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C343770C01
1.292,1.344 0.521,0.885 0.521,0.885 1.292,1.208 true 2.479,1.917 1.719,2.76 1.719,2.76 2.479,1.583 true 1.563,2.781 1.875,3.083 0.313,0.302 10 false *1 0.333,0.719 0.615,1 0.281,0.281 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the front oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C191042C02
1,2.354 1,2.948 false 1.396,0.948 1.24,0.292 1.24,0.292 1.115,0.292 false 2.552,0.802 2.417,0.927 2.417,0.927 2.417,1.042 false 2.688,1.5 2.563,1.635 2.563,1.635 2.563,1.74 false 2.156,0.323 2.271,0.469 0.115,0.146 10 false A 0.927,0.198 1.385,0.49 0.458,0.292 10 false *a 0.906,2.958 1.083,3.135 0.177,0.177 10 false *b 2.479,1.781 3.042,2.156 0.563,0.375 10 false *b 2.354,1.083 2.792,1.365 0.438,0.281 10 false *a
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C343739N01
2.323,0.313 2.604,0.646 0.281,0.333 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 33403M 2.INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY

a.

Apply ATF to a new O-ring and install it to the speedometer driven hole (ATM) cover sub-assembly.

NOTICE:

Ensure that the O-ring are not twisted.



b.

Install the speedometer driven hole (ATM) cover sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

Make sure that the O-ring is not damaged or does not jump out of the position during installation.



Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the automatic transaxle assembly with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12311A 5.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 36100 6.INSTALL TRANSFER ASSEMBLY

Hide 30500 7.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C298989

Clean and degrease the bolt and bolt hole in the automatic transaxle assembly.


b.
C343740C01
1.615,0.969 2.313,0.969 false 0.938,1 1.229,1.24 0.292,0.24 10 false *1 2.365,0.854 2.719,1.115 0.354,0.26 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



c.
C298990C01
0.677,1.271 1.01,1.552 0.333,0.281 10 false *a 2.594,0.479 2.927,0.76 0.333,0.281 10 true *a 0.771,2.781 1.104,3.063 0.333,0.281 10 false B 1.156,2.396 1.49,2.677 0.333,0.281 10 false A 1.646,2.344 1.979,2.625 0.333,0.281 10 false A 2.573,2.438 2.906,2.719 0.333,0.281 10 false A 2.76,3.021 3.094,3.302 0.333,0.281 10 false A 2.813,3.615 3.146,3.896 0.333,0.281 10 false A 2.729,3.958 3.063,4.24 0.333,0.281 10 false A 2.406,4.281 2.74,4.563 0.333,0.281 10 false C 1.385,4.385 1.646,4.594 0.26,0.208 10 false C 1.115,4.167 1.375,4.375 0.26,0.208 10 true C
*a Knock Pin


While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and temporarily install the 10 bolts shown in the illustration.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (C) : 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the automatic transaxle assembly contact surface of the engine cylinder block before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.



HINT:

Bolt length:

·

Bolt (A): 55 mm (2.17 in.)

·

Bolt (B): 50 mm (1.97 in.)

·

Bolt (C): 33 mm (1.30 in.)




d.
P000601C48
2.458,0.198 2.24,0.198 2.24,0.198 1.99,1.188 false 2.521,0.115 2.813,0.292 0.292,0.177 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Make sure to install the bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



e.
C298989N01
0.76,1.708 0.917,1.938 0.156,0.229 10 true D

Install the bolt.

Torque:
Bolt (D) : 46 N*m (469 kgf*cm, 34 ft.*lbf)

HINT:

Bolt length:

Bolt (D): 41 mm (1.61 in.)




Hide 36118A 8.INSTALL TRANSFER STIFFENER PLATE RH

a.
C296629C02
2.094,0.365 2.219,0.146 2.219,0.146 2.385,0.146 true 1.208,0.354 1.146,0.146 1.146,0.146 0.99,0.146 true 2.427,0.063 2.688,0.292 0.26,0.229 10 true *2 2.833,0.479 3.24,0.708 0.406,0.229 10 true 3 (*b) 2.958,1.219 3.354,1.448 0.396,0.229 10 true 4 (*b) 0.479,0.521 0.875,0.75 0.396,0.229 10 true 1 (*a) 0.104,1.031 0.5,1.24 0.396,0.208 10 true 2 (*a) 0.76,0.073 0.958,0.302 0.198,0.229 10 true *1
*1 Transfer Stiffener Plate RH
*2 Rear Engine Mounting Bracket
*a Bolt (A)
*b Bolt (B)


Temporarily install the transfer stiffener plate RH to the transfer assembly and the rear engine mounting bracket with the 4 bolts.


b.

Install the 4 bolts in the order shown in the illustration.

Torque:
Bolt (A) : 34 N*m (347 kgf*cm, 25 ft.*lbf)
Bolt (B) : 78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 16587 9.INSTALL RADIATOR PIPE CLAMP

a.

Install the clamp to the radiator pipe clamp.


b.

Install the radiator pipe clamp with the clamp to the engine assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Engage the breather plug to the clamp.


d.

Engage the air fuel ratio sensor wire harness.


Hide 10.CONNECT WIRE HARNESS

a.
C297900C03
2.24,0.833 2.49,1.073 0.25,0.24 10 true *a 1.052,1.24 1.208,1.438 0.156,0.198 10 true A 1.135,2.583 1.292,2.781 0.156,0.198 10 true B
*a Park/Neutral Position Switch Connector


Engage the 5 clamps to the automatic transaxle assembly.


b.

Connect the wire harness to the automatic transaxle assembly with the 2 bolts.

Torque:
Bolt (A) : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Bolt (B) : 23 N*m (235 kgf*cm, 17 ft.*lbf)


c.

Connect the park/neutral position switch connector.


Hide 51100G 13.INSTALL FRONT FRAME ASSEMBLY

Hide 14.INSTALL STEERING LINK ASSEMBLY

Hide 48811 15.INSTALL FRONT STABILIZER BAR

Hide 48829A 16.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 17.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 32101A 19.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
P000601C48
2.458,0.198 2.24,0.198 2.24,0.198 1.99,1.188 false 2.521,0.115 2.813,0.292 0.292,0.177 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



b.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 20.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 21.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION