1.INSTALL HOLE PLUG
for 1AR-FE:
Install the 14 hole plugs to the front frame assembly.
There are 4 different shapes of hole plug.
for 2GR-FKS:
Install the 10 hole plugs to the front frame assembly.
There are 2 different shapes of hole plug.
52217E
2.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
| *a | View from Underneath |
|
Front of the Vehicle |
Temporarily install a new front suspension member body mounting rear cushion LH while confirming the installation direction.
Position the front suspension member body mounting rear cushion LH in the correct direction.
| *1 | Front Suspension Member Body Mounting Rear Cushion LH |
Install SST as shown in the illustration.
| *a | Hold |
| *b | Turn |
Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.
Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion LH.
52215
3.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH
| *a | View from Underneath |
|
Front of the Vehicle |
Temporarily install a new front suspension member body mounting rear cushion RH while confirming the installation direction.
Position the front suspension member body mounting rear cushion RH in the correct direction.
Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.
Using SST, install the front suspension member body mounting rear cushion RH.
Perform the same procedure as for the LH side.
52211J
4.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION
| *a | View from Underneath |
|
Front of the Vehicle |
Temporarily install a new front suspension member body mounting front cushion while confirming the installation direction.
Position the front suspension member body mounting front cushion in the correct direction.
Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.
| *a | Hold |
| *b | Turn |
Using SST, install each front suspension member body mounting front cushion as shown in the illustration.
Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.
52216B
5.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.
52213A
6.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
Install the 2 front suspension member body mounting front stoppers to the front frame assembly.
51227B
7.INSTALL FRONT SUSPENSION MEMBER DYNAMIC DAMPER (for 1AR-FE)
Install the front suspension member dynamic damper to the front frame assembly with the 2 bolts.
51229B
8.INSTALL NO. 2 FRAME CROSSMEMBER DYNAMIC DAMPER (for 2GR-FKS)
for 2WD:
Install the No. 2 frame crossmember dynamic damper to the front frame assembly with the 2 bolts.
for AWD:
Install the No. 2 frame crossmember dynamic damper to the front frame assembly with the 2 bolts.
48069
9.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48068
10.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
11.INSTALL STEERING LINK ASSEMBLY
48811
12.INSTALL FRONT STABILIZER BAR
Install the front stabilizer bar with 2 front No. 2 stabilizer brackets, 2 front No. 1 stabilizer bar bushings and 2 front stabilizer link assemblies to the front frame assembly.
48829A
13.INSTALL FRONT NO. 1 STABILIZER BRACKET LH
48824A
14.INSTALL FRONT NO. 1 STABILIZER BRACKET RH
Perform the same procedure as for the LH side.
12380
15.INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FKS)
12372A
16.INSTALL ENGINE MOUNTING INSULATOR LH
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
12362
17.INSTALL ENGINE MOUNTING INSULATOR RH
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
12361
18.INSTALL FRONT ENGINE MOUNTING INSULATOR (for 1AR-FE)
12360
19.INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FKS)
51100G
20.INSTALL FRONT FRAME ASSEMBLY
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION