Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for LHD) › from 2016.11
RM3160E _54 Brake _019693 BRAKE SYSTEM (OTHER) _0108088 BRAKE MASTER CYLINDER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


PROCEDURE

Hide 1.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 53299D 2.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 3.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 4.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 5.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (for 1AR-FE)

Hide 17750A 6.REMOVE INLET AIR CLEANER ASSEMBLY (for 1AR-FE)

Hide 17705 7.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE (for 1AR-FE)

Hide 17801 8.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for 1AR-FE)

Hide 17701 9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 1AR-FE)

Hide 11209 10.REMOVE V-BANK COVER SUB-ASSEMBLY (for 2GR-FKS)

Hide 17750A 11.REMOVE INLET AIR CLEANER ASSEMBLY (for 2GR-FKS)

Hide 17700 12.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for 2GR-FKS)

Hide 47234L 13.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C292882

Slide the clip and disconnect the No. 1 reservoir hose from the brake master cylinder sub-assembly.


Hide 14.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY WITH WAY

a.
C292883

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly with way.

NOTICE:
·

Do not damage or deform the brake lines during the removal procedure.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




b.
C292884

Remove the 2 nuts and brake master cylinder sub-assembly with way from the brake booster assembly.

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not allow the brake master cylinder sub-assembly to receive any impact, such as from being dropped. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.




Hide 47201B 15.REMOVE BRAKE MASTER CYLINDER O-RING

a.

Remove the brake master cylinder O-ring from the brake master cylinder sub-assembly.