Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › from 2016.11
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298227 DIFFERENTIAL OIL SEAL A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53737B 2.REMOVE FRONT FENDER APRON SEAL LH

Hide 3.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C361064

Remove the refill plug and gasket from the automatic transaxle case sub-assembly.


b.
C361060

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.


c.
C361063C01
2.729,1 2.906,1 true 2.563,0.906 2.875,1.104 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.


d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



f.

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



Hide 12321A 5.REMOVE REAR ENGINE MOUNTING BRACKET (for 2WD)

Hide 43420H 6.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C361040N01
0.917,2.563 1.365,1.802 false 0.792,2.604 1.25,2.802 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the automatic transaxle case sub-assembly.



Hide 43410M 7.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C361041N01
2.198,2.802 1.927,1.74 false 2.083,2.823 2.542,3.021 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.



Hide 43410M 8.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C400537C01
2.125,1.115 2.792,0.813 2.792,0.813 2.188,1.292 true 1.667,3.052 1.979,3.208 0.313,0.156 10 false *a 2.844,0.719 3.302,0.917 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09316-10010  
09950-70010  (09951-07150)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 43420H 9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C361042C01
1.719,1.188 2.792,1.625 2.792,1.625 2.021,1.031 true 2.844,1.583 3.302,1.781 0.458,0.198 10 true SST 1.906,3.146 2.073,3.333 0.167,0.188 10 true *a
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 12321A 10.INSTALL REAR ENGINE MOUNTING BRACKET (for 2WD)

Hide 13.INSPECT FOR FLUID LEAK

Hide 53737B 14.INSTALL FRONT FENDER APRON SEAL LH

Hide 51441 15.INSTALL NO. 1 ENGINE UNDER COVER