Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY › from 2016.11
RM3160E _52 Drivetrain _019686 DRIVE SHAFT / PROPELLER SHAFT _0107997 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 37100 1.TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

a.
C293530N01
0.781,1.031 1.458,1.031 true 0.458,0.938 0.771,1.125 0.313,0.188 10 true SST

Remove SST from the transfer assembly.


b.

Insert the propeller with center bearing shaft assembly into the transfer assembly.

NOTICE:
·

Be careful not to damage the transfer extension housing type T oil seal.

·

Be careful not to damage the universal joint boot when installing the propeller with center bearing shaft assembly.




c.
C293526C01
2.385,2.021 2.885,2.021 2.885,2.021 2.885,1.531 true 2.792,2.01 2.792,1.583 true 2.229,1.938 2.542,2.094 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks on the electro magnetic control coupling sub-assembly and propeller with center bearing shaft assembly.


d.
C293527

Temporarily install the 4 nuts and 4 washers.

NOTICE:

Do not allow grease to adhere to the 4 bolts, 4 nuts and 4 washers.



e.
C365708

Temporarily install the propeller with center bearing shaft assembly with the 4 bolts, and 4 No. 2 center support bearing washers.

NOTICE:
·

Reuse the No. 2 center support bearing washers.

·

Do not allow grease to adhere to the 4 bolts or 4 No. 2 center support bearing washers.




f.
C293527

Fully tighten the 4 nuts.

Torque:
73.5 N*m (749 kgf*cm, 54 ft.*lbf)


Hide 37100 2.FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

a.
C293525C01
2.542,2.344 2.542,2.146 2.542,2.146 2.781,2.146 true 2.813,2.052 3.125,2.25 0.313,0.198 10 false *a
*a Piece of Cloth


Remove the piece of cloth or equivalent from the universal joint flange.


b.

Using a 6 mm hexagon socket wrench, fully tighten the 6 cross groove joint set bolts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
C293540N01
2.281,1.344 2.438,1.542 0.156,0.198 10 false A

With the vehicle unloaded, adjust the distance (A) between the rear side of the cover and shaft as shown in the illustration.

Distance (A):

58 mm (2.28 in.)



d.

With the vehicle unloaded, adjust the front and rear distance (A) between the edge surface of the No. 2 center support bearing assembly and the edge surface of the cushion respectively as shown in the illustration, and then tighten the bolts.

C293541C01
0.625,0.25 0.938,0.448 0.313,0.198 10 false *a 4,0.26 4.313,0.458 0.313,0.198 10 false *b 1.885,2.375 2.198,2.573 0.313,0.198 10 false A 5.146,2.385 5.458,2.583 0.313,0.198 10 false A 2.156,0.667 2.635,0.854 0.479,0.188 10 true 90° 5.417,0.698 5.896,0.885 0.479,0.188 10 true 90°
*a No. 2 Center Support Bearing Assembly (for Front Side) *b No. 2 Center Support Bearing Assembly (for Rear Side)


Distance (A):

11.5 to 13.5 mm (0.453 to 0.531 in.)



e.
C365708

Fully tighten the 4 bolts.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


f.

Check that the center line of the bracket is at a right angle to the shaft axial direction.


Hide 4.INSPECT AND ADJUST JOINT ANGLE

NOTICE:

Measure the joint angle when the vehicle is raised using a four-post lift or when using a pit.


HINT:

If any vibration or noise occurs, perform the joint angle check as follows and replace the No. 2 center support bearing washer with a proper one.


a.

Stabilize the propeller shaft and differential.

i.

Turn the propeller shaft several times by hand to stabilize the center support bearings.


ii.

Using a jack, raise and lower the differential to stabilize the differential mounting cushion.



b.

Check the No. 1 and No. 4 joint angles.

C293542C01
0.49,1.542 0.688,1.542 false 1.26,1.552 1.458,1.552 false 4.375,1.594 4.573,1.594 false 6.438,1.656 6.635,1.656 false 1.135,2.115 1.292,2.313 0.156,0.198 10 false B 0.354,2.125 0.51,2.323 0.156,0.198 10 false A 4.615,2.167 4.771,2.365 0.156,0.198 10 false C 6.313,2.271 6.469,2.469 0.156,0.198 10 false D 0.656,0.375 0.969,0.573 0.313,0.198 10 false *a 5.813,0.469 6.125,0.667 0.313,0.198 10 false *b 0.74,1.458 1.198,1.656 0.458,0.198 10 false SST 1.51,1.479 1.969,1.677 0.458,0.198 10 false SST 4.083,1.51 4.542,1.708 0.458,0.198 10 false SST 6.688,1.573 7.146,1.771 0.458,0.198 10 false SST
*a No. 1 Joint Angle *b No. 4 Joint Angle


i.

Using SST, measure the transfer assembly installation angle (A) and propeller shaft assembly installation angle (B).

SST
09370-50010  

No. 1 Joint Angle:
Measurement Position No. 1 Joint Angle
A-B -3.02° to -1.02°



ii.

Using SST, measure the rear propeller shaft assembly installation angle (C) and rear differential carrier assembly installation angle (D).

SST
09370-50010  

No. 4 Joint Angle:
Measurement Position No. 4 Joint Angle
C-D 0.71° to 2.71°


If the measured angle is not within the specified range, adjust it with No. 2 center support bearing washer.



c.

Adjust the No. 1 joint angle and No. 4 joint angle.

i.

Select No. 2 center support bearing washers for adjustment.

No. 2 Center Support Bearing Washer Thickness:
Part No. Thickness mm (in.)
90201-10095 3.2 mm (0.126 in.)
90201-10081 4.5 mm (0.177 in.)
90201-10083 6.5 mm (0.256 in.)
90201-10084 9.0 mm (0.354 in.)
90201-10085 11.0 mm (0.433 in.)
90201-10086 13.5 mm (0.531 in.)
90201-10134 15.5 mm (0.610 in.)
90201-10135 17.5 mm (0.689 in.)


NOTICE:
·

Make sure to use a No. 2 center support bearing washers of the same thickness on both the right and left sides.

·

Do not use 2 or more washers on a bolt.





Hide 51569F 5.INSTALL PROPELLER SHAFT GUARD (for Front Side)

a.

Install the propeller shaft guard with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 51569G 6.INSTALL PROPELLER SHAFT GUARD (for Rear Side)

a.
C385637C01
1.073,0.958 1.313,0.958 false 2.656,0.958 2.896,0.958 false 0.281,0.333 0.594,0.531 0.313,0.198 10 false *A 1.885,0.323 2.198,0.521 0.313,0.198 10 false *B 1.344,0.844 1.656,1.042 0.313,0.198 10 false *a 2.927,0.844 3.24,1.042 0.313,0.198 10 false *b
*A for Type A
*B for Type B
*a Bolt Color: Silver
*b Bolt Color: Silver and Red


Install the propeller shaft guard with the bolt and nut.

Torque:
Bolt (for Type A) : 32 N*m (326 kgf*cm, 24 ft.*lbf)
Bolt (for Type B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 7.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket with the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Engage the 2 clamps.


Hide 58167A 8.INSTALL FRONT CENTER FLOOR COVER

Hide 51442 10.INSTALL NO. 2 ENGINE UNDER COVER