Home › Engine / Hybrid System › 2GR-FKS FUEL › FUEL TANK › from 2016.11
RM3160E _51 Engine / Hybrid System _060158 2GR-FKS FUEL _0298786 FUEL TANK A

2GR-FKS FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77158A 1.INSTALL TANK SUCTION TUBE SUPPORT

a.
A314698C01
1.073,0.354 1.51,0.354 false 2.229,0.323 2.531,0.323 false 0.646,2.76 0.865,2.76 false 1.635,2.167 1.906,2.167 false 0.875,0.25 1.188,0.406 0.313,0.156 10 false *a 0.438,2.667 0.625,2.833 0.188,0.167 10 true *b 2.573,0.24 2.885,0.396 0.313,0.156 10 false *a 1.948,2.083 2.115,2.24 0.167,0.156 10 true *b
*a Protrusion
*b Notch


Install a new tank suction tube support to the fuel tank assembly.

HINT:

Align the protrusions of the tank suction tube support with the notches of the fuel tank assembly.



Hide 77608C 2.INSTALL FUEL TANK CUSHION SET

a.

Install the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions to the fuel tank assembly.


Hide 77213B 3.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A375474C02
2.25,2.813 2.344,2.813 2.344,2.813 2.646,2.677 true 1.292,2.229 1.521,1.948 1.521,1.948 1.594,1.948 false 0.844,3.063 1.156,3.219 0.313,0.156 10 false *a 1.01,1.76 1.323,1.917 0.313,0.156 10 false *b 2.073,2.729 2.385,2.885 0.313,0.156 10 false *c 1.646,1.885 1.958,2.042 0.313,0.156 10 false *d 3.021,2.438 3.333,2.594 0.313,0.156 10 false *e
*a 0 to 3.0 mm (0 to 0.118 in.)
*b Clamp Area
*c Stopper
*d Paint Mark
*e +/- 2.0 mm (0.0787 in.)
V100136

Up


Install the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.

HINT:
·

Make sure the clamp and fuel tank to filler pipe hose are positioned within the area shown in the illustration.

·

Make sure that the clamp end is positioned within 2.0 mm (0.0787 in.) of the stopper.




Hide 77209F 4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 3 claws to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77113B 5.INSTALL FUEL TANK SIDE PLATE

a.

Install a new fuel tank side plate to the fuel tank assembly with the fuel tank band pin and fuel tank cushion.


Hide 77100 6.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.

Using the engine lifter, slowly raise the fuel tank assembly, and then install the fuel tank assembly, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH with the 4 bolts.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




c.

Install the rear fuel tank bracket LH with the bolt and nut.

Torque:
Bolt : 39.2 N*m (400 kgf*cm, 29 ft.*lbf)
Nut : 19.6 N*m (200 kgf*cm, 14 ft.*lbf)


d.

Install the nut.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


e.

Connect the fuel cut off valve with tube assembly to the charcoal canister assembly.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION


Hide 77213B 7.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A375475C02
2.063,2.26 2.156,2.26 2.156,2.26 2.354,2.594 false 1.813,4.063 1.906,4.063 1.906,4.063 2.083,3.917 true 2.781,3.01 2.677,3.01 2.677,3.01 2.427,2.615 true 0.844,2.125 1.156,2.281 0.313,0.156 10 false *a 1.448,2.521 1.76,2.677 0.313,0.156 10 false *b 2.323,3.042 2.635,3.198 0.313,0.156 10 false *c 2.448,2.021 2.76,2.177 0.313,0.156 10 false *d 1.646,3.99 1.958,4.146 0.313,0.156 10 false *e 2.448,3.708 2.76,3.865 0.313,0.156 10 false *f 2.833,2.948 3.146,3.104 0.313,0.156 10 false *g 1.885,2.198 2.198,2.354 0.313,0.156 10 false *h
*a Up
*b 120°
*c 0 to 3.0 mm (0 to 0.118 in.)
*d Clamp Area
*e Stopper
*f +/- 2.0 mm (0.0787 in.)
*g Alignment Mark (Fuel Tank To Filler Pipe Hose Side)
*h Alignment Mark (Fuel Tank To Filler Pipe Side)


Connect the fuel tank to filler pipe hose to the fuel tank filler pipe assembly and tighten the clamp to secure it.

HINT:
·

Make sure the clamp and fuel tank to filler pipe hose are positioned within the area shown in the illustration.

·

Make sure that the clamp end is positioned within 2.0 mm (0.0787 in.) of the stopper.




Hide 8.CONNECT FUEL TANK BREATHER TUBE

a.
A375476C02
1.698,4.115 1.823,4.115 1.823,4.115 2.083,4.042 true 0.729,2.26 1.042,2.417 0.313,0.156 10 false *a 1.281,2.698 1.594,2.854 0.313,0.156 10 false *b 2.656,3.198 2.969,3.354 0.313,0.156 10 false *c 2.604,2.26 2.917,2.417 0.313,0.156 10 false *d 1.51,4.042 1.823,4.198 0.313,0.156 10 false *e 2.469,3.833 2.781,3.99 0.313,0.156 10 false *f
*a Up
*b 120°
*c 0 to 3.0 mm (0 to 0.118 in.)
*d 2.0 to 7.0 mm (0.0787 to 0.276 in.)
*e Stopper
*f +/- 2.0 mm (0.0787 in.)


Connect the fuel tank breather tube to the fuel tank filler pipe assembly and tighten the clamp to secure it.

HINT:
·

Make sure the clamp and fuel tank breather tube are positioned within the area shown in the illustration.

·

Make sure that the clamp end is positioned within 2.0 mm (0.0787 in.) of the stopper.




Hide 77209F 9.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION


Hide 77606 10.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector sub-assembly with the 7 nuts and 4 new clips.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 77765 11.INSTALL CHARCOAL CANISTER PROTECTOR

Hide 58167A 12.INSTALL FRONT CENTER FLOOR COVER

a.

Engage the 4 clips to install the front center floor cover.


b.

Install the 2 screws and nut.


Hide 51206A 13.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY (for 2WD)

Hide 51206A 14.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY (for AWD)

Hide 15.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 16.ADD FUEL