Home › Engine / Hybrid System › 2GR-FKS FUEL › FUEL PUMP(for High Pressure) › from 2016.11
RM3160E _51 Engine / Hybrid System _060158 2GR-FKS FUEL _0298784 FUEL PUMP(for High Pressure) A

2GR-FKS FUEL  FUEL PUMP(for High Pressure)  INSTALLATION  


PROCEDURE

Hide 23100X 1.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY

a.
A368943C01
1.167,1.708 1.167,0.875 1.167,0.875 1.333,0.875 true 1.167,1.333 1.417,1.333 true 2.583,1.75 2.417,1.75 2.417,1.75 1.75,1.167 true 1.271,2.5 1.521,2.5 false 1.219,3.167 1.385,3.167 false 0.917,4.479 0.917,4.313 false 2.5,4.438 2.5,4.188 false 2.813,3.052 2.979,3.052 false 2.875,2.5 3.083,2.5 false 3.125,2.417 3.385,2.594 0.26,0.177 10 false *1 1.438,3.094 1.75,3.25 0.313,0.156 10 false *2 0.844,4.5 1.156,4.656 0.313,0.156 10 false *3 0.823,2.208 1.135,2.365 0.313,0.156 10 false *a 2.458,2.229 2.771,2.385 0.313,0.156 10 false *b 1.563,2.427 1.875,2.583 0.313,0.156 10 false *1 3.031,2.99 3.344,3.146 0.313,0.156 10 false *2 2.417,4.479 2.729,4.635 0.313,0.156 10 false *3 2.635,1.667 2.833,1.844 0.198,0.177 10 true *3 1.083,1.74 1.271,1.917 0.188,0.177 10 true *c
*1 Fuel Pump Assembly
*2 Fuel Pump Lifter Assembly
*3 Camshaft
*a Correct
*b Incorrect
*c Oil Collection Area


Turn the crankshaft pulley until the flat of the camshaft faces the fuel pump lifter assembly.

HINT:

This prevents the camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump assembly.



b.

Fill the fuel pump lifter housing oil collection areas with 30 cc (1.8 cu. in.) of engine oil from the fuel pump assembly hole of the cylinder head cover sub-assembly.


c.
A368944C01
1.74,0.979 1.958,0.323 1.958,0.323 2.135,0.323 true 2.833,2.219 2.833,1.688 true 1.74,2.125 1.74,1.615 true 1.167,2.115 1.167,1.313 true 1.781,3.885 2.458,3.885 true 2.75,2.26 3.063,2.417 0.313,0.156 10 false *1 1.667,2.167 1.979,2.323 0.313,0.156 10 false *2 1.073,2.156 1.385,2.313 0.313,0.156 10 false *3 2.188,0.24 2.365,0.396 0.177,0.156 10 true *a 2.521,3.813 2.833,3.969 0.313,0.156 10 false *b
*1 Cylinder Head Cover Sub-assembly
*2 Fuel Pump Spacer Gasket
*3 Fuel Pump Lifter Housing
*a Pump Drive Cam (Engine Oil Application Area)
*b Fuel Pump Lifter Assembly (Engine Oil Application Area)


Apply engine oil to the pump drive cam and fuel pump lifter assembly.


d.

Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly.


e.
A368945C01
1.802,0.583 2.115,0.583 false 2.458,0.771 2.771,0.771 false 2.229,2.083 2.625,1.604 2.625,1.604 2.75,1.604 false 1.51,1.427 1.646,1.427 1.646,1.427 1.927,2.052 true 1.635,0.5 1.948,0.656 0.313,0.156 10 false *a 1.313,1.354 1.49,1.521 0.177,0.167 10 true *b 2.813,0.698 3.125,0.854 0.313,0.156 10 false *c 2.802,1.531 3.115,1.688 0.313,0.156 10 false *d
*a Fuel Pump Lifter Assembly (Engine Oil Application Area)
*b Fuel Pump Lifter Housing (Engine Oil Application Area)
*c Stopper Key
*d Key Groove


Apply engine oil to the inside of the fuel pump lifter housing and the outside of the fuel pump lifter assembly.


f.

Set the fuel pump lifter assembly on the fuel pump lifter housing as shown in the illustration.

HINT:

Align the stopper key of the fuel pump lifter assembly with the key groove of the fuel pump lifter housing.



g.

Apply engine oil to a new O-ring and install it to the fuel pump assembly.

NOTICE:

Do not damage the O-ring.



h.
A393312C01
2.365,1.26 2.667,1.26 false 2.24,1.969 2.542,1.969 false 2.719,1.167 3.031,1.323 0.313,0.156 10 false *1 2.594,1.885 2.906,2.042 0.313,0.156 10 false *2
*1 Fuel Pump Assembly
*2 Fuel Pump Lifter Guide


Set the fuel pump lifter guide and fuel pump assembly on the cylinder head cover sub-assembly as shown in the illustration.


i.

Temporarily install the fuel pump assembly with the 2 bolts, leaving some allowance for left and right movement.


Hide 23801P 2.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

NOTICE:

Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.


a.

Connect the No. 1 fuel pipe sub-assembly to the fuel delivery pipe RH and tighten the union nut by hand.


b.

Connect the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.


Hide 23100X 3.INSTALL FUEL PUMP ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Tighten the 2 bolts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


b.

Connect the fuel pump assembly connector.


Hide 23801P 4.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A393313C01
2.823,2.469 2.938,2.469 2.938,2.469 2.938,2.854 false 2.656,2.375 2.969,2.531 0.313,0.156 10 false *a 1.719,2.448 2.031,2.604 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe RH side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




Hide 23881B 5.INSTALL FUEL HOSE BRACKET

a.

Install the fuel hose bracket to the cylinder head cover sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 6.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Engage the clamp and connect the No. 2 fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION


Hide 23214A 7.INSTALL FUEL PUMP PROTECTOR

a.

Install the fuel pump protector to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Engage the clamp to connect the fuel tube sub-assembly to the fuel pump protector.


Hide 51442 8.INSTALL NO. 2 ENGINE UNDER COVER

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION