Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER(for 2WD) › 2016.11–2018.09
RM3160E _53 Suspension _019690 REAR SUSPENSION _0109436 REAR SUSPENSION MEMBER(for 2WD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for 2WD)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
C296804

Install the 13 hole plugs to the rear suspension member sub-assembly as shown in the illustration.

HINT:

The upper and lower hole plug shapes are different.



Hide 52271D 2.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C296957C01
0.052,0.063 0.365,0.302 0.313,0.24 10 false *A 0.167,0.417 0.479,0.573 0.313,0.156 10 false *a 0.667,0.917 0.969,1.156 0.302,0.24 10 false *b 2.771,0.417 3.083,0.656 0.313,0.24 10 false *c 2.76,0.885 3.073,1.125 0.313,0.24 10 false *c
*A View from Underneath
*a Front of the Vehicle
*b Left Side of the Vehicle
*c 45°


Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.


b.
C199924N08
2.063,0.448 2.354,0.448 false 2.042,0.698 2.51,0.698 true 2.385,0.375 2.698,0.552 0.313,0.177 10 false SST 2.542,0.625 2.844,0.833 0.302,0.208 10 false SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C199927C01
1.021,0.792 1.427,0.792 true 1.219,0.979 1.448,0.979 true 2.667,0.844 2.979,1 0.313,0.156 10 false *a 2.188,1.885 2.5,2.042 0.313,0.156 10 false *b 0.719,0.708 1.177,0.906 0.458,0.198 10 false SST 0.917,0.906 1.375,1.104 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52271D 3.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

a.
C296956C01
0.073,0.063 0.375,0.313 0.302,0.25 10 false *A 0.26,0.417 0.573,0.573 0.313,0.156 10 false *a 0.719,0.885 1.031,1.042 0.313,0.156 10 false *b 2.281,0.427 2.583,0.677 0.302,0.25 10 false *c 2.219,0.896 2.531,1.146 0.313,0.25 10 true *c
*A View from Underneath
*a Front of the Vehicle
*b Left Side of the Vehicle
*c 45°


Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.


b.
C205620N02
1.021,0.406 1.406,0.406 false 1.042,0.708 1.427,0.708 true 0.719,0.323 1.177,0.521 0.458,0.198 10 false SST 0.76,0.615 1.219,0.813 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C205621C01
1.271,0.802 1.469,0.802 false 1.292,0.979 1.49,0.979 true 2.781,0.865 3.094,1.021 0.313,0.156 10 false *a 2.24,1.969 2.552,2.125 0.313,0.156 10 false *b 1,0.708 1.292,0.906 0.292,0.198 10 true SST 1,0.906 1.302,1.104 0.302,0.198 10 true SST
*a Turn
*b Hold


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52276A 4.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION LH

a.
C296955C01
0.104,0.052 0.417,0.365 0.313,0.313 10 false *A 2.573,0.156 2.885,0.313 0.313,0.156 10 false *a 3.052,0.604 3.365,0.76 0.313,0.156 10 false *b
*A View from Underneath
*a Front of the Vehicle
*b Left Side of the Vehicle


Temporarily install the rear suspension member rear body mounting cushion LH while confirming the installation direction.


b.
C199925N02
1.385,0.5 1.208,0.292 1.208,0.292 1.042,0.292 false 0.74,0.208 1.198,0.406 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mounting cushion LH.



c.
C199928C01
1.052,0.604 1.25,0.604 1.25,0.604 1.479,0.771 true 2.719,0.906 3.031,1.063 0.313,0.156 10 false *a 2.198,1.896 2.51,2.052 0.313,0.156 10 false *b 0.781,0.542 1.208,0.74 0.427,0.198 10 true SST
*a Turn
*b Hold


Using SST, install the rear suspension member rear body mounting cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52275B 5.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION RH

a.
C296958C01
0.063,0.063 0.375,0.313 0.313,0.25 10 false *A 0.646,0.271 0.958,0.427 0.313,0.156 10 false *a 0.167,0.729 0.479,0.885 0.313,0.156 10 false *b 0.333,1.542 0.646,1.792 0.313,0.25 10 false *c 2.313,1.563 2.625,1.813 0.313,0.25 10 false *c
*A View from Underneath
*a Front of the Vehicle
*b Right Side of the Vehicle
*c 15°


Temporarily install the rear suspension member rear body mounting cushion RH while confirming the installation direction.


b.
C199926N02
1.896,0.51 2.115,0.281 2.115,0.281 2.438,0.281 false 2.51,0.198 2.969,0.396 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mounting cushion RH.



c.
C199929C01
1.01,0.594 1.281,0.594 1.281,0.594 1.49,0.771 false 2.802,0.896 3.115,1.052 0.313,0.156 10 false *a 2.208,1.885 2.521,2.042 0.313,0.156 10 false *b 0.698,0.521 1.156,0.719 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, install the rear suspension member rear body mounting cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 48790 6.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89516B 8.INSTALL SKID CONTROL SENSOR WIRE LH

a.
C199896

Install the skid control sensor wire LH with the 2 bolts and nut.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 89516 9.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272 10.INSTALL REAR SUSPENSION MEMBER UPPER STOPPER

a.
C199916

Install the 2 rear suspension member upper stoppers to the rear suspension member sub-assembly.

NOTICE:

Be sure to install the rear suspension member upper stoppers in the correct direction shown in the illustration.



Hide 52277B 11.INSTALL REAR SUSPENSION MEMBER REAR UPPER STOPPER

a.
C199915

Install the 2 rear suspension member rear upper stoppers to the rear suspension member sub-assembly.


Hide 51206A 12.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C301600C02
2.792,4.073 2.792,3.906 2.792,3.906 2.948,3.906 false 2.208,4.208 2.729,4.208 false 2.594,4.208 2.594,4.125 2.594,4.125 2.479,4.125 false 0.729,4.188 0.896,4.188 false 1.615,4.188 1.615,4.083 1.615,4.083 1.938,4.083 true 2.979,3.833 3.281,4.021 0.302,0.188 10 false *a 0.563,4.094 0.76,4.281 0.198,0.188 10 true *b 2.771,4.125 3.083,4.281 0.313,0.156 10 false *c 1.531,4.198 1.802,4.375 0.271,0.177 10 true *b
*a Engine Lifter
*b Attachment
*c Wooden Block
V100155

Attachment placement location


Support the rear suspension member sub-assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools as shown in the illustration.

CAUTION:

Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.


NOTICE:
·

Use the attachments to keep the rear suspension member sub-assembly level.

·

The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Temporarily install the rear No. 1 suspension arm assembly LH.

i.
C350826C01
2.365,1.656 2.875,1.656 false 2.823,2 3.021,2 false 0.823,1.552 1.094,1.552 1.094,1.552 1.625,0.719 true 1.479,3.99 1.479,4.208 false 2.906,1.552 3.219,1.708 0.313,0.156 10 false *a 3.042,1.906 3.292,2.125 0.25,0.219 10 false *b 0.656,1.458 0.844,1.688 0.188,0.229 10 true *c 1.406,4.229 1.719,4.385 0.313,0.156 10 false *d 0.979,0.115 1.177,0.292 0.198,0.177 10 true B 2.302,0.281 2.49,0.51 0.188,0.229 10 true A
*a Wooden Block
*b Jack
*c Opening
*d Spacer
V100136

Front of the Vehicle


Support the rear axle assembly LH with a jack using a wooden block as shown in the illustration.

CAUTION:

Do not jack up the rear axle assembly LH too high as the vehicle may fall.


NOTICE:

When jacking up the rear axle assembly LH, be sure to jack it up slowly.



ii.

Temporarily install the rear No. 1 suspension arm assembly LH to the rear axle carrier sub-assembly LH with the spacer and nut (A).

NOTICE:
·

Install the rear No. 1 suspension arm assembly with its opening facing downward.

·

Fully tighten the nut (A) after stabilizing the suspension.

·

Be sure to install the rear No. 1 suspension arm assembly with the spacer facing in the correct direction as shown in the illustration.




iii.

Temporarily install the rear No. 1 suspension arm assembly LH to the rear suspension member sub-assembly with the bolt (B) and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Fully tighten the bolt (B) after stabilizing the suspension.





c.

Slowly lower the rear axle assembly LH.


d.

Temporarily install the rear No. 1 suspension arm assembly RH.

HINT:

Perform the same procedure as for the LH side.



e.

Install the rear suspension member sub-assembly with the 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH, with the 4 bolts and 2 nuts.

C199912C01
0.781,1.438 1.26,1.438 true 5.802,1.427 6.271,1.427 true 0.594,1.344 0.885,1.563 0.292,0.219 10 false *1 6.302,1.344 6.594,1.563 0.292,0.219 10 false *1
*1 Rear Lower Suspension Brace - -


Torque:
Bolt : 158 N*m (1611 kgf*cm, 117 ft.*lbf)
Nut : 32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:

Be sure to install the rear suspension member sub-assembly with the rear lower suspension braces facing in the correct direction as shown in the illustration.



f.

Lower the engine lifter.


g.

Connect the rear upper control arm assembly LH.

i.
C199880

Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

HINT:

Pushing out the bushing makes it easier to connect the rear upper control arm assembly LH.



ii.
C199878C03
2.177,1.604 2.563,1.604 false 2.385,1.833 2.771,1.833 false 2.594,1.521 2.875,1.698 0.281,0.177 10 false *a 2.802,1.76 3.083,1.948 0.281,0.188 10 false *b
*a Wooden Block
*b Jack


Support the rear axle assembly LH with a jack using a wooden block as shown in the illustration.

CAUTION:

Do not jack up the rear axle assembly LH too high as the vehicle may fall.


NOTICE:

When jacking up the rear axle assembly LH, be sure to jack it up slowly.



iii.

Connect the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




iv.

Slowly lower the rear axle assembly LH.



h.

Connect the rear upper control arm assembly RH.

HINT:

Perform the same procedure as for the LH side.



Hide 13.INSTALL FRAME WIRE

a.

Install the frame wire to the rear suspension member sub-assembly with the bolt, each clamp and each connector as shown in the illustration.

C296849N01
4.833,0.313 4.979,0.5 0.146,0.188 10 true A 4.156,0.198 4.302,0.406 0.146,0.208 10 true B

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Do not twist the frame wire when installing it.


HINT:

The connector (A) and clamp (B) are only on vehicles with the LED headlight system.



Hide 48740F 14.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 15.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 16.INSTALL REAR STABILIZER BAR

Hide 48802 17.INSTALL REAR STABILIZER LINK SUB-ASSEMBLY LH

Hide 48802 18.INSTALL REAR STABILIZER LINK SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89516B 19.INSTALL SKID CONTROL SENSOR WIRE LH

Hide 89516 20.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 47319F 21.INSTALL REAR FLEXIBLE HOSE LH

a.
C293049

Install the rear flexible hose LH to the rear upper control arm assembly LH with the bolt.

Torque:
18.8 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not twist the rear flexible hose LH when installing it.

·

Do not damage the rear flexible hose when installing it.

·

If the rear flexible hose LH is damaged, replace it with a new one.




b.
C293048C04
1.458,0.813 1.958,0.813 true 1.354,1.396 1.635,1.396 true 1.271,0.708 1.448,0.906 0.177,0.198 10 true *1 1.156,1.271 1.333,1.479 0.177,0.208 10 true *2
*1 Rear No. 4 Brake Tube
*2 Rear Flexible Hose LH
V100136

Clip


Install the rear flexible hose with a new clip.

NOTICE:

Install the clip as far as it will go.



c.

Using a union nut wrench, connect the rear flexible hose LH to the rear No. 4 brake tube while holding the rear flexible hose LH with a wrench.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 47318F 22.INSTALL REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 24.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 25.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48738 26.INSTALL REAR SUSPENSION ARM COVER LH

Hide 48737 27.INSTALL REAR SUSPENSION ARM COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 89408D 28.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Hide 30.BLEED BRAKE LINE

Hide 31.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 48740F 32.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 33.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 34.INSPECT AND ADJUST REAR WHEEL ALIGNMENT