Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Main body ECU (multiplex network body ECU) branch line or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly ground circuit

·

Main body ECU (multiplex network body ECU) or instrument panel junction block assembly



WIRING DIAGRAM

C408703E01
5.385,7.125 7.052,7.521 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 5.438,0.323 5.896,0.521 0.458,0.198 10 false F19 5.438,0.99 5.896,1.188 0.458,0.198 10 false F19 5.469,0.104 5.781,0.302 0.313,0.198 10 false 14 5.469,0.781 5.781,0.979 0.313,0.198 10 false 13 0.896,2.719 1.969,2.917 1.073,0.198 10 false from Battery 2.667,7.115 4.292,7.542 1.625,0.427 10 false Instrument Panel Junction Block Assembly 2.792,1.865 3.104,2.063 0.313,0.198 10 false 4D 2.792,1.635 3.104,1.833 0.313,0.198 10 false 23 1.729,2.448 2.938,2.698 1.208,0.25 10 false MPX-B NO. 1 5.448,1.854 5.76,2.052 0.313,0.198 10 false MB 5.469,1.646 5.781,1.844 0.313,0.198 10 false 31 5.854,1.854 6.469,2.052 0.615,0.198 10 false BECU 5.833,0.323 6.448,0.521 0.615,0.198 10 false CANH 5.844,0.99 6.458,1.188 0.615,0.198 10 false CANL 5.844,2.74 6.302,2.938 0.458,0.198 10 false ACC 5.438,2.74 5.75,2.938 0.313,0.198 10 false MB 5.469,2.531 5.781,2.729 0.313,0.198 10 false 30 5.448,5.813 5.76,6.01 0.313,0.198 10 false MB 5.458,6.688 5.771,6.885 0.313,0.198 10 false MB 4.51,2.885 5.583,3.083 1.073,0.198 10 false ECU-ACC 3.469,3.51 4.844,3.708 1.375,0.198 10 false ACC Relay 2.781,2.74 3.094,2.938 0.313,0.198 10 false 4K 2.781,3.208 3.094,3.406 0.313,0.198 10 false 4A 2.823,2.521 2.979,2.719 0.156,0.198 10 false 1 2.802,2.99 3.115,3.188 0.313,0.198 10 false 28 2.229,2.896 2.688,3.094 0.458,0.198 10 false ALT 0.344,3.208 1.875,3.854 1.531,0.646 10 false Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch*2 0.333,4.469 1.865,5.115 1.531,0.646 10 false Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch*2 2.781,4.271 3.094,4.469 0.313,0.198 10 false 16 2.781,4.49 3.094,4.688 0.313,0.198 10 false 4A 4.469,4.385 5.281,4.625 0.813,0.24 10 false IG1 NO. 3 3.188,4.771 4.438,5.042 1.25,0.271 10 false IG1 NO. 3 Relay 2.792,5.365 3.104,5.563 0.313,0.198 10 false 4F 2.792,5.813 3.104,6.01 0.313,0.198 10 false 4F 2.781,6.25 3.094,6.448 0.313,0.198 10 false 4A 2.781,6.688 3.094,6.885 0.313,0.198 10 false 4D 5.469,5.604 5.781,5.802 0.313,0.198 10 false 32 5.854,5.802 6.167,6 0.313,0.198 10 false IG 2.781,5.135 3.094,5.333 0.313,0.198 10 false 19 2.792,5.604 3.104,5.802 0.313,0.198 10 false 24 2.792,6.042 3.104,6.24 0.313,0.198 10 false 27 2.781,6.479 3.094,6.677 0.313,0.198 10 false 11 5.469,6.479 5.781,6.677 0.313,0.198 10 false 11 5.844,6.698 6.458,6.896 0.615,0.198 10 false GND1 1.594,0.177 1.75,0.375 0.156,0.198 10 false 6 1.563,0.844 1.875,1.042 0.313,0.198 10 false 16 0.083,1.344 0.698,1.542 0.615,0.198 10 false F102 0.479,1.344 4.76,1.542 4.281,0.198 10 false No. 3 CAN Junction Connector 0.177,1.854 2.146,2.271 1.969,0.417 10 false from Door Control Battery*3 0.094,6.417 2.219,6.813 2.125,0.396 10 false *1: w/ Smart Key System 0.104,6.76 2.229,7.156 2.125,0.396 10 false *2: w/o Smart Key System 0.115,7.094 2.24,7.49 2.125,0.396 10 false *3: for LHD 0.115,7.438 2.24,7.833 2.125,0.396 10 false *4: for RHD 0.5,2.292 1.99,2.833 1.49,0.542 10 false from Battery*4

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*

*: w/ Smart Entry and Start System




HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result:
Result Proceed to
for LHD A
for RHD B




A

2.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)

B

5.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C285509C06
1.25,0.281 1.646,0.521 0.396,0.24 1.813,1.25 1.833,0.333 1.833,0.333 2.021,0.333 true 1.917,1.24 2.063,0.573 2.063,0.573 2.26,0.573 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.333,0.313 1.646,0.51 0.313,0.198 10 false F19 2.073,0.25 2.688,0.448 0.615,0.198 10 false CANL 2.333,0.479 2.948,0.677 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Disconnect the F19 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-14 (CANH) - F19-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) POWER SOURCE CIRCUIT
a.

Check the main body ECU (multiplex network body ECU) power source circuit.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>Power Source Circuit


Result:
Result
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 3 RELAY AND ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 3 RELAY AND ACC RELAY)
a.

Inspect the IG1 No. 3 relay and ACC relay of the instrument panel junction block assembly.


HINT:

In case IG signal circuit and ACC signal circuit have no problem, replace the main body ECU (multiplex network body ECU).



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C285509C06
1.25,0.281 1.646,0.521 0.396,0.24 1.813,1.25 1.833,0.333 1.833,0.333 2.021,0.333 true 1.917,1.24 2.063,0.573 2.063,0.573 2.26,0.573 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.333,0.313 1.646,0.51 0.313,0.198 10 false F19 2.073,0.25 2.688,0.448 0.615,0.198 10 false CANL 2.333,0.479 2.948,0.677 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Disconnect the F19 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-14 (CANH) - F19-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 4D instrument panel junction block assembly connector.


b.
C298411C01
1.469,0.208 1.885,0.51 0.417,0.302 0.844,1.844 0.948,1.844 0.948,1.844 1.375,1.177 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.594,0.26 1.906,0.458 0.313,0.198 10 false 4D 0.417,1.75 1.031,1.948 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-11 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.
C298411C02
1.469,0.208 1.885,0.51 0.417,0.302 0.844,1.844 0.948,1.844 0.948,1.844 1.375,1.333 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.594,0.26 1.906,0.458 0.313,0.198 10 false 4D 0.417,1.75 1.031,1.948 0.615,0.198 10 false BECU
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4D-23 (BECU) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 3 RELAY AND ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 3 RELAY AND ACC RELAY)
a.

Inspect the IG1 No. 3 relay and ACC relay of the instrument panel junction block assembly.


HINT:

In case IG signal circuit and ACC signal circuit have no problem, replace the main body ECU (multiplex network body ECU).



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY