Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0298899 ENGINE UNIT A

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16587 1.INSTALL RADIATOR PIPE CLAMP

a.

Install the radiator pipe clamp to the camshaft housing sub-assembly LH with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.

Install the wire harness clamp bracket to the cylinder head cover LH with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12321A 3.INSTALL REAR ENGINE MOUNTING BRACKET (for 2WD)

a.

Install the rear engine mounting bracket to the cylinder block sub-assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12321A 4.INSTALL REAR ENGINE MOUNTING BRACKET (for AWD)

a.

Install the rear engine mounting bracket to the cylinder block sub-assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12585 5.INSTALL NO. 5 CYLINDER BLOCK INSULATOR

a.
A374183C01
2.375,3.031 0.729,2.688 0.729,2.688 2.573,2.125 true 2.063,2.75 0.802,2.688 0.802,2.688 2.573,2.323 true 0.542,2.604 0.854,2.76 0.313,0.156 10 false *a
*a Fastener Surface


Install the No. 5 cylinder block insulator to the engine assembly.

NOTICE:

Make sure that the No. 5 cylinder block insulator is not covering any fastener surface.



Hide 11452 6.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new engine oil level dipstick guide O-ring to the engine oil level dipstick guide.


b.

Apply a light coat of engine oil to the engine oil level dipstick guide O-ring.


c.

Insert the engine oil level dipstick guide end into the oil pan sub-assembly.


d.

Install the engine oil level dipstick guide to the camshaft housing sub-assembly LH with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Install the engine oil level dipstick to the engine oil level dipstick guide.


Hide 16173 7.INSTALL WATER PUMP PULLEY

Hide 16620 8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16604 9.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 88431 10.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A373765N01
1.458,0.167 1.615,0.365 0.156,0.198 10 true A 2.302,0.708 2.458,0.906 0.156,0.198 10 true B

Install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 88310 11.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 27020 12.INSTALL GENERATOR ASSEMBLY

Hide 12262 14.INSTALL NO. 2 VENTILATION HOSE

a.

Install the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 12261 15.INSTALL VENTILATION HOSE

a.

Install the ventilation hose to the PCV valve (ventilation valve sub-assembly) and slide the clip to secure it.


Hide 16264 16.INSTALL NO. 2 WATER BY-PASS HOSE

a.

Install the No. 2 water by-pass hose to the water outlet and slide the clip to secure it.


Hide 16267 17.INSTALL NO. 3 WATER BY-PASS HOSE

a.

Install the No. 3 water by-pass hose to the water inlet pipe and slide the clip to secure it.


Hide 29300 18.INSTALL VACUUM PUMP ASSEMBLY

Hide 82219A 20.INSTALL SENSOR WIRE

a.

Engage the 2 clamps and install the sensor wire to the water inlet pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89615 21.INSTALL KNOCK CONTROL SENSOR