Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  P034511  Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground  P034515  Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open  P034531  Camshaft Position Sensor "A" Bank 2 No Signal  


DESCRIPTION

The VVT sensor (for the intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The intake camshaft has a timing rotor for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system..

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground The VVT sensor (for intake camshaft of bank 1) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored SAE Code: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open The VVT sensor (for intake camshaft of bank 1) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored SAE Code: P0343
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal A missing VVT sensor (for intake camshaft of bank 1) signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored SAE Code: P0340
P034511 Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground The VVT sensor (for intake camshaft of bank 2) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored SAE Code: P0347
P034515 Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open The VVT sensor (for intake camshaft of bank 2) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored SAE Code: P0348
P034531 Camshaft Position Sensor "A" Bank 2 No Signal A missing VVT sensor (for intake camshaft of bank 2) signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored SAE Code: P0345

A356009E02
0.094,1.323 0.479,1.542 0.385,0.219 10 false CH1 0.135,2.063 0.469,2.271 0.333,0.208 10 false CH2 2.813,1.479 3.271,1.677 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND 2.677,0.771 3.302,1 0.625,0.229 10 false 5 V/DIV. 1.25,2.552 2.938,2.75 1.688,0.198 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the VVT sensor (for intake camshaft of bank 1) signal, and VV2 stands for the VVT sensor (for intake camshaft of bank 2) signal.



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for intake camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) VVT sensor (for intake camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P034011, P034015, P034031, P034511, P034515 or P034531.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A357733E09
1.917,0.802 2.229,1 0.313,0.198 10 false VC 2.198,0.813 2.354,1.01 0.156,0.198 10 false 3 1.75,1.365 2.365,1.563 0.615,0.198 10 false VVR+ 2.188,1.354 2.344,1.552 0.156,0.198 10 false 1 1.771,1.885 2.385,2.083 0.615,0.198 10 false VVR- 2.198,1.885 2.354,2.083 0.156,0.198 10 false 2 0.969,2.365 1.427,2.563 0.458,0.198 10 false C35 0.969,2.542 3.781,2.833 2.813,0.292 10 false VVT Sensor (for Intake Camshaft of Bank 1) 4.771,0.813 5.083,1.01 0.313,0.198 10 false 99 4.698,1.333 5.156,1.531 0.458,0.198 10 false 132 4.708,1.896 5.167,2.094 0.458,0.198 10 false 100 5.01,0.813 5.625,1.01 0.615,0.198 10 false VCV1 5.01,1.333 5.625,1.531 0.615,0.198 10 false VV1+ 5.021,1.885 5.635,2.083 0.615,0.198 10 false VV1- 5.531,5.156 5.875,5.385 0.344,0.229 10 false C1 5.854,5.156 6.313,5.354 0.458,0.198 10 false ECM 1.906,3.25 2.219,3.448 0.313,0.198 10 false VC 2.188,3.25 2.344,3.448 0.156,0.198 10 false 3 1.771,3.771 2.385,3.969 0.615,0.198 10 false VVL+ 2.188,3.771 2.344,3.969 0.156,0.198 10 false 1 1.792,4.281 2.219,4.5 0.427,0.219 10 false VVL- 2.198,4.292 2.354,4.49 0.156,0.198 10 false 2 0.979,4.823 1.438,5.021 0.458,0.198 10 false C36 0.979,5.021 3.708,5.396 2.729,0.375 10 false VVT Sensor (for Intake Camshaft of Bank 2) 4.781,3.24 5.094,3.438 0.313,0.198 10 false 98 4.708,3.771 5.167,3.969 0.458,0.198 10 false 129 4.792,4.302 5.104,4.5 0.313,0.198 10 false 97 5.01,3.24 5.625,3.438 0.615,0.198 10 false VCV2 5.021,3.771 5.635,3.969 0.615,0.198 10 false VV2+ 5.031,4.302 5.646,4.5 0.615,0.198 10 false VV2-

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE CAMSHAFT))
A376492C39
0.198,1.156 0.552,1.406 0.354,0.25 0.198,0.813 0.552,1.063 0.354,0.25 1.958,1.167 2.448,1.76 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.26,1.177 0.573,1.375 0.313,0.198 10 false C36 2.396,1.771 2.708,1.969 0.313,0.198 10 false VC 0.25,0.833 0.563,1.031 0.313,0.198 10 false C35 0.583,0.823 0.896,1.021 0.313,0.198 10 false *b 0.583,1.167 0.896,1.365 0.313,0.198 10 false *c
*a Front view of wire harness connector
(to VVT Sensor (for Intake Camshaft))
*b Bank 1
*c Bank 2


a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C35-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
C36-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C35-1 (VVR+) - C1-132 (VV1+) Always Below 1 Ω
C35-2 (VVR-) - C1-100 (VV1-) Always Below 1 Ω
C36-1 (VVL+) - C1-129 (VV2+) Always Below 1 Ω
C36-2 (VVL-) - C1-97 (VV2-) Always Below 1 Ω
C35-1 (VVR+) or C1-132 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C35-2 (VVR-) or C1-100 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C36-1 (VVL+) or C1-129 (VV2+) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (VVL-) or C1-97 (VV2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Check the VVT sensor (for intake camshaft) installation condition.

OK:

VVT sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

A370145C01
0.927,0.677 1.583,0.333 false 5.583,0.917 6.167,0.333 false 1.083,1.417 1.604,0.698 false 1.083,1.417 1.604,0.99 false 0.917,0.833 1.583,0.333 false 5.635,0.646 6.167,0.333 false 5.667,1.417 6.26,0.813 false 5.667,1.417 6.25,0.667 false 1.781,3.208 2.333,3.5 false 0.927,3 1.531,3.24 false 1.656,0.25 1.969,0.448 0.313,0.198 10 false *a 0.896,1.323 1.208,1.521 0.313,0.198 10 false *a 6.219,0.25 6.531,0.448 0.313,0.198 10 false *a 5.479,1.323 5.792,1.521 0.313,0.198 10 false *a 2.396,3.427 2.708,3.625 0.313,0.198 10 false *b 0.719,2.906 1.031,3.104 0.313,0.198 10 false *c
*a Timing Mark *b TDC Timing Mark
*c Groove - -



b.

Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)

NG

8.CHECK ENGINE MECHANICAL SYSTEM
6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)
a.

Replace the VVT sensor (for intake camshaft).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P034031, P034511, P034515 OR P034531)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P034031, P034511, P034515 OR P034531)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P034011, P034015, P034031, P034511, P034515 or P034531 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B

8.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P034031, P034511, P034515 OR P034531)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P034031, P034511, P034515 OR P034531)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P034011, P034015, P034031, P034511, P034515 or P034531 is output B




A

B

10.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C35-3 (VC) - C1-99 (VCV1) Always Below 1 Ω
C36-3 (VC) - C1-98 (VCV2) Always Below 1 Ω
C35-3 (VC) or C1-99 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C36-3 (VC) or C1-98 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR