Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic).
·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

ECM


Comes on DTC stored SAE Code: P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure Either of the following conditions A or B is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more:
(a) Any 2 or more of the following signals are on simultaneously:
·

P input signal

·

R input signal

·

D input signal


(b) Any 2 or more of the following signals are on simultaneously:
·

N input signal

·

R input signal

·

D input signal


(c) Any 2 or more of the following signals are on simultaneously:
·

NSW input signal

·

R input signal

·

D input signal


B. Any of the following conditions is met for 2 seconds or more with the shift lever in M:
·

NSW input signal is on

·

P input signal is on

·

N input signal is on

·

R input signal is on


·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

Open or short in transmission control switch circuit

·

Transmission control switch (shift lever assembly)

·

ECM


Comes on DTC stored SAE Code: P0705

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or M). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Park/Neutral position switch assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Move the shift lever to R and wait 2 seconds or more.

7.

Move the shift lever to N and wait 2 seconds or more.

8.

Move the shift lever to D and wait 2 seconds or more.

9.

Move the shift lever to M and wait 2 seconds or more.

10.

Move the shift lever to P and wait 2 seconds or more.

11.

Wait 1 minute or more.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P070513 or P070562.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A349645E29
1.052,1.167 2.74,1.365 1.688,0.198 10 false to ST Relay 0.542,2.51 2.229,2.813 1.688,0.302 10 false from BKUP LP Fuse 0.198,5.167 2,5.385 1.802,0.219 10 false from IG1 NO. 3 Fuse 2.604,1.104 2.927,1.313 0.323,0.208 10 false 9 2.583,2.615 2.906,2.823 0.323,0.208 10 false 1 2.771,1.104 3.094,1.313 0.323,0.208 10 false L 2.76,2.615 3.083,2.823 0.323,0.208 10 false RB 2.229,3.969 2.552,4.177 0.323,0.208 10 false C14 2.229,4.104 4.802,4.333 2.573,0.229 10 false Park/Neutral Position Switch Assembly 2.563,5.094 2.885,5.302 0.323,0.208 10 false 3 2.771,5.094 3.094,5.302 0.323,0.208 10 false IG 3.573,5.094 3.896,5.302 0.323,0.208 10 false S 3.771,5.094 4.094,5.302 0.323,0.208 10 false 7 2.427,5.573 2.75,5.781 0.323,0.208 10 false F46 2.417,5.729 5.156,6.031 2.74,0.302 10 false Transmission Control Switch 5.198,5.156 5.521,5.365 0.323,0.208 10 false A43 5.24,5 5.563,5.208 0.323,0.208 10 false 17 5.604,5.198 5.927,5.406 0.323,0.208 10 false S 5.781,5.813 6.167,6.083 0.385,0.271 10 false ECM 3.521,3.5 3.844,3.708 0.323,0.208 10 false PL 3.531,2.906 3.854,3.115 0.323,0.208 10 false RL 3.521,2.313 3.844,2.521 0.323,0.208 10 false NL 3.521,1.708 3.844,1.917 0.323,0.208 10 false DL 3.573,1.104 3.896,1.313 0.323,0.208 10 false B 3.792,1.104 4.115,1.313 0.323,0.208 10 false 4 3.792,1.708 4.115,1.917 0.323,0.208 10 false 7 3.792,2.302 4.115,2.51 0.323,0.208 10 false 8 3.781,2.906 4.104,3.115 0.323,0.208 10 false 2 3.781,3.5 4.104,3.708 0.323,0.208 10 false 3 5.219,1.167 5.542,1.375 0.323,0.208 10 false C1 5.198,1 5.583,1.219 0.385,0.219 10 false 106 5.594,1.198 6.281,1.458 0.688,0.26 10 false NSW 5.198,1.604 5.604,1.813 0.406,0.208 10 false 139 5.219,1.771 5.542,1.979 0.323,0.208 10 false C1 5.229,2.375 5.552,2.583 0.323,0.208 10 false C1 5.219,2.969 5.542,3.177 0.323,0.208 10 false C1 5.229,3.573 5.552,3.781 0.323,0.208 10 false C1 5.208,2.208 5.604,2.417 0.396,0.208 10 false 140 5.208,2.813 5.625,3.031 0.417,0.219 10 false 107 5.208,3.417 5.604,3.615 0.396,0.198 10 false 108 5.615,1.802 5.938,2.01 0.323,0.208 10 false D 5.615,2.396 5.938,2.604 0.323,0.208 10 false N 5.604,2.979 5.927,3.188 0.323,0.208 10 false R 5.604,3.615 5.927,3.823 0.323,0.208 10 false P 0.5,2.833 2.167,3.156 1.667,0.323 10 false from ECU-ACC Fuse

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Shift SW Status (P Range), Shift SW Status (R Range), Shift SW Status (N Range), Shift SW Status (S Range) and Shift SW Status (D Range).

Powertrain > Engine > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (S Range)
Shift SW Status (D Range)
50003 372 15,14,13,27,28

e.

Read the values displayed on the GTS.

GTS Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


-
Shift SW Status (R Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Shift SW Status (N Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


-
Shift SW Status (S Range) Transmission control switch status:
ON or OFF
·

ON: Shift lever in M

·

OFF: Shift lever not in M


-
Shift SW Status (D Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


-



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Neutral Position SW and Shift SW Status (P, R, N and D Range).

Powertrain > Engine > Data List
Tester Display
Neutral Position SW
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 372 20,15,14,13,28

e.

According to the display on the GTS, read the Data List.

OK:
GTS Display Shift Lever Position Specified Condition
Neutral Position SW P or N ON
Except P or N OFF
Shift SW Status (P Range) P ON
Except P OFF
Shift SW Status (R Range) R ON
Except R OFF
Shift SW Status (N Range) N ON
Except N OFF
Shift SW Status (D Range) D or M ON
Except D or M OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Shift SW Status (S Range).

Powertrain > Engine > Data List
Tester Display
Shift SW Status (S Range)
50003 372 27

e.

Read the Data List displayed on the GTS.

OK:
GTS Display Shift Lever Position Specified Condition
Shift SW Status (S Range) M ON
Except M OFF



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.

Inspect the transmission control switch.



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF TRANSMISSION CONTROL SWITCH)
C168574C18
0.625,2.063 0.969,2.313 0.344,0.25 1.875,2.979 1.844,2.156 true 0.219,0.094 0.542,0.354 0.323,0.26 10 false *a 0.677,2.083 1.094,2.344 0.417,0.26 10 false F46 1.813,3.031 2.125,3.292 0.313,0.26 10 false IG
*a Front view of wire harness connector
(to Transmission Control Switch)


a.

Disconnect the transmission control switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F46-3 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F46-7 (S) - A43-17 (S) Always Below 1 Ω
F46-7 (S) or A43-17 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
A372148C03
0.469,1 0.854,1.198 0.385,0.198 1.573,1.615 1.615,1.073 true 0.26,0.229 0.573,0.427 0.313,0.198 10 false *a 0.531,1 0.99,1.198 0.458,0.198 10 false C14 1.49,1.625 1.802,1.823 0.313,0.198 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


a.

Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C14-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE CIRCUIT)

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C14-4 (B) - C1-106 (NSW) Always Below 1 Ω
C14-7 (DL) - C1-139 (D) Always Below 1 Ω
C14-8 (NL) - C1-140 (N) Always Below 1 Ω
C14-2 (RL) - C1-107 (R) Always Below 1 Ω
C14-3 (PL) - C1-108 (P) Always Below 1 Ω
C14-4 (B) or C1-106 (NSW) - Body ground and other terminals Always 10 kΩ or higher
C14-7 (DL) or C1-139 (D) - Body ground and other terminals Always 10 kΩ or higher
C14-8 (NL) or C1-140 (N) - Body ground and other terminals Always 10 kΩ or higher
C14-2 (RL) or C1-107 (R) - Body ground and other terminals Always 10 kΩ or higher
C14-3 (PL) or C1-108 (P) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR