Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump (for low pressure side) circuit consists of the ECM, fuel pump (for low pressure side) and fuel pump control ECU (which operates the fuel pump (for low pressure side)). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU. Based on the signal sent from the ECM, the fuel pump control ECU adjusts the fuel pump (for low pressure side) operation speed.

WIRING DIAGRAM

A398329E02
6.073,0.656 6.677,0.958 0.604,0.302 10 false MREL 5.833,0.542 6.146,0.792 0.313,0.25 10 false 46 3.573,0.635 3.885,0.896 0.313,0.26 10 false 1G 3.625,0.448 3.802,0.708 0.177,0.26 10 false 6 3.615,1.104 3.833,1.365 0.219,0.26 10 false 8 3.563,1.281 3.917,1.552 0.354,0.271 10 false 1G 2.229,1.604 3.042,1.865 0.813,0.26 10 false EFI MAIN 1.469,1.458 2.167,1.75 0.698,0.292 10 false EFI-MAIN 1.146,1.271 1.385,1.542 0.24,0.271 10 false B 1.146,1.073 1.344,1.292 0.198,0.219 10 false 1 1.479,2.021 3.927,2.365 2.448,0.344 10 false Semiconductor Pwr Integration ECU 4.333,1.625 5.135,1.917 0.802,0.292 10 false EFI NO. 4 0.469,4.198 1.396,4.521 0.927,0.323 10 false FL MAIN 0.625,5.323 1.333,5.646 0.708,0.323 10 false Battery 0.448,6.292 1.333,6.604 0.885,0.313 10 false *: Shielded 1.406,6.031 1.813,6.313 0.406,0.281 10 false M48 1.75,6.031 2.969,6.51 1.219,0.479 10 false Fuel Pump (for low pressure side) 2.146,5.521 2.74,5.802 0.594,0.281 10 false BLPE 2.604,5.396 2.792,5.656 0.188,0.26 10 false 1 2.125,4.99 2.729,5.24 0.604,0.25 10 false BLPW 2.615,4.875 2.813,5.125 0.198,0.25 10 false 2 2.156,4.458 2.698,4.708 0.542,0.25 10 false BLPV 2.615,4.333 2.813,4.573 0.198,0.24 10 false 4 2.177,3.927 2.74,4.167 0.563,0.24 10 false BLPU 2.604,3.813 2.792,4.073 0.188,0.26 10 false 3 1.771,2.792 2.677,3.094 0.906,0.302 10 false FUEL PMP 4.573,2.031 4.76,2.281 0.188,0.25 10 false 2 5.323,2.031 5.521,2.281 0.198,0.25 10 false 1 4.583,2.5 4.792,2.76 0.208,0.26 10 false 3 5.333,2.49 5.542,2.75 0.208,0.26 10 false 5 4.646,2.948 5.521,3.24 0.875,0.292 10 false FUEL PMP 3.208,5.656 3.406,5.896 0.198,0.24 10 false * 3.646,3.927 4.052,4.198 0.406,0.271 10 false M46 3.646,4.448 4.083,4.698 0.438,0.25 10 false M46 3.625,4.99 4.083,5.188 0.458,0.198 10 false M46 3.635,5.521 4.042,5.792 0.406,0.271 10 false M46 3.719,3.719 3.917,3.958 0.198,0.24 10 false 2 4,3.917 4.427,4.156 0.427,0.24 10 false FPU 3.729,4.26 3.906,4.49 0.177,0.229 10 false 3 3.979,4.458 4.427,4.74 0.448,0.281 10 false FPV 3.708,4.813 3.896,5.052 0.188,0.24 10 false 4 3.99,5 4.469,5.271 0.479,0.271 10 false FPW 3.698,5.323 3.917,5.573 0.219,0.25 10 false 1 4,5.531 4.458,5.865 0.458,0.333 10 false FPG 4.521,4.115 4.865,4.365 0.344,0.25 10 false +B 4.802,4.135 5.219,4.396 0.417,0.26 10 false M47 4.813,4.688 5.24,4.938 0.427,0.25 10 false M47 4.802,5.271 5.177,5.583 0.375,0.313 10 false M47 4.448,4.698 4.865,4.969 0.417,0.271 10 false FPC 4.417,5.271 4.802,5.51 0.385,0.24 10 false GND 4.875,3.927 5.094,4.156 0.219,0.229 10 false 1 4.875,4.49 5.052,4.75 0.177,0.26 10 false 2 4.875,5.083 5.083,5.323 0.208,0.24 10 false 3 5.823,4.552 6.135,4.823 0.313,0.271 10 false 18 6.083,4.563 6.51,4.813 0.427,0.25 10 false FPC 6.052,6.031 6.469,6.292 0.417,0.26 10 false A43 6.417,6.042 6.875,6.344 0.458,0.302 10 false ECM 3.635,6.052 5.25,6.49 1.615,0.438 10 false Fuel Pump Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT FUEL PUMP CONTROL ECU
A337223C19
4.292,0.208 4.656,0.49 0.365,0.281 2.667,0.219 3.042,0.479 0.375,0.26 5,2.365 4.719,1.323 false 4.458,2.375 4.458,1.333 false 3.917,2.375 4.177,1.333 false 3.438,2.375 3.24,1.458 false 3.083,2.375 3.01,1.448 false 2.615,2.375 2.719,1.448 false 2.146,2.375 2.469,1.438 false 0.281,0.188 0.594,0.385 0.313,0.198 10 false *1 4.354,0.25 4.667,0.448 0.313,0.198 10 false M47 2.729,0.24 3.042,0.438 0.313,0.198 10 false M46 4.958,2.417 5.271,2.615 0.313,0.198 10 false +B 3.792,2.417 4.167,2.646 0.375,0.229 10 false GND 4.365,2.417 4.74,2.646 0.375,0.229 10 false FPC 3.354,2.417 3.729,2.646 0.375,0.229 10 false FPG 2.969,2.417 3.344,2.646 0.375,0.229 10 false FPU 2.5,2.417 2.875,2.646 0.375,0.229 10 false FPV 2.042,2.417 2.417,2.646 0.375,0.229 10 false FPW
*1 Fuel Pump Control ECU - -


a.

Remove the fuel pump control ECU.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL PUMP ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M47-1 (+B) - M47-3 (GND) Always 200 Ω or higher
M47-1 (+B) - M47-2 (FPC) Always 2 kΩ or higher
M47-2 (FPC) - M47-3 (GND) Always 10 kΩ or higher
M46-1 (FPG) - M47-3 (GND) Always 1 kΩ or higher
M46-2 (FPU) - M47-3 (GND) Always 2 kΩ or higher
M46-3 (FPV) - M47-3 (GND) Always 2 kΩ or higher
M46-4 (FPW) - M47-3 (GND) Always 2 kΩ or higher


HINT:

This procedure checks for an internal short of the fuel pump control ECU when its transistor is stuck on.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)

NG

REPLACE FUEL PUMP CONTROL ECU

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)
A355999C24
0.542,1.125 0.906,1.375 0.365,0.25 1.125,1.76 1.375,1.333 false 2.333,1.729 2.063,1.344 false 0.229,0.323 0.542,0.521 0.313,0.198 10 false *a 0.604,1.156 0.917,1.354 0.313,0.198 10 false M47 0.99,1.771 1.302,1.969 0.313,0.198 10 false +B 2.219,1.76 2.531,1.958 0.313,0.198 10 false GND
*a Front view of wire harness connector
(to Fuel Pump Control ECU)


a.

Disconnect the fuel pump control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M47-1 (+B) - M47-3 (GND) Ignition switch ON 11 to 14 V


HINT:

Make a note of the measured voltage as it may be used in a following Active Test.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF FUEL PMP RELAY)
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M47-2 (FPC) - A43-18 (FPC) Always Below 1 Ω
M47-2 (FPC) or A43-18 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
A337225C19
2.677,0.229 3.052,0.51 0.375,0.281 3.25,2.292 3,1.458 false 2.208,2.281 2.458,1.458 false 2.729,2.271 2.729,1.49 false 0.208,0.156 0.521,0.354 0.313,0.198 10 false *1 2.74,0.271 3.052,0.469 0.313,0.198 10 false M46 3.167,2.302 3.5,2.51 0.333,0.208 10 false FPU 2.615,2.302 2.927,2.5 0.313,0.198 10 false FPV 2.031,2.302 2.417,2.51 0.385,0.208 10 false FPW
*1 Fuel Pump Control ECU - -


a.

Disconnect the M46 fuel pump control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
M46-2 (FPU) - Body ground U Phase 4.4 to 8.4 V*
M46-3 (FPV) - Body ground V Phase 4.4 to 8.4 V*
M46-4 (FPW) - Body ground W Phase 4.4 to 8.4 V*


HINT:
·

*: This Active Test restricts the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage measured in a previous step.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Result Proceed to
The U phase, V phase and W phase are all normal A
The U phase, V phase or W phase is abnormal B
The U phase, V phase and W phase are all abnormal C



A

5.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PUMP CONTROL ECU

C

6.INSPECT ECM (FPC TERMINAL)
5.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pump control ECU connector.


b.

Disconnect the fuel pump (for low pressure side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M46-2 (FPU) - M48-3 (BLPU) Always Below 1 Ω
M46-3 (FPV) - M48-4 (BLPV) Always Below 1 Ω
M46-4 (FPW) - M48-2 (BLPW) Always Below 1 Ω
M46-2 (FPU) or M48-3 (BLPU) - Body ground and other terminals Always 10 kΩ or higher
M46-3 (FPV) or M48-4 (BLPV) - Body ground and other terminals Always 10 kΩ or higher
M46-4 (FPW) or M48-2 (BLPW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



OK

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (FPC TERMINAL)
A355999C25
0.563,1.104 0.969,1.375 0.406,0.271 1.719,1.75 1.719,1.365 false 0.208,0.292 0.521,0.448 0.313,0.156 10 false *a 0.625,1.146 1.083,1.344 0.458,0.198 10 false M47 1.604,1.76 2.063,1.958 0.458,0.198 10 false FPC
*a Front view of wire harness connector
(to Fuel Pump Control ECU)


a.

Disconnect the fuel pump control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Fuel Pump Single Phase Energization.

Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49

f.

Operate the fuel pump control ECU using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition
M47-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF FUEL PMP RELAY)
a.

Remove the FUEL PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FUEL PMP relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL PMP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FUEL PMP RELAY)

8.INSPECT FUEL PMP RELAY

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - ECM)

NG

REPLACE FUEL PMP RELAY

9.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - ECM)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-6 - A43-46 (MREL) Always Below 1 Ω
1G-6 or A43-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - FUEL PMP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - FUEL PMP RELAY)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Remove the FUEL PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-8 - 2 (FUEL PMP relay) Always Below 1 Ω
1G-8 or 2 (FUEL PMP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FUEL PMP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FUEL PMP RELAY - BODY GROUND)
a.

Remove the FUEL PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (FUEL PMP relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL PMP RELAY - FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL PMP RELAY - FUEL PUMP CONTROL ECU)
a.

Remove the FUEL PMP relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the fuel pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (FUEL PMP relay) - M47-1 (+B) Always Below 1 Ω
5 (FUEL PMP relay) or M47-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
a.

Disconnect the fuel pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M47-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR