Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When vehicle speed is 3 km/h (2 mph) or more and stop light switch assembly is OFF, master cylinder pressure continuously exceeds 1.764 Mpa (18.0 kgf/cm2, 255 psi) for 5 seconds or more.
·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (brake actuator assembly)

·

Skid control ECU (brake actuator assembly)



HINT:

for C1422: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.

1.

Turn the ignition switch to ON.

2.

Keep the vehicle stationary for 5 seconds or more and depress the brake pedal lightly 2 or 3 times.

3.

Drive the vehicle at the vehicle speed of 50 km/h (31 mph) and depress and hold the brake pedal firmly for approximately 3 seconds.

4.

Repeat the above operation 3 times or more and check that the ABS warning light goes off.

5.

Clear the DTCs.



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1425 is output together with C1422, inspect and repair the trouble areas indicated by C1425 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 105 37,39

d.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



e.

Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.

OK:

First the stop light switch should turn on, and then the brake pedal load sensing switch should turn on.



Result:
Proceed to
OK A
NG (The stop light switch does not turn on.) B
NG (Turning on of the brake pedal load sensing switch is not confirmed.) C
NG (The brake pedal load sensing switch turns on first.) D



A

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

C

6.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

D

8.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Pressure Master cylinder pressure sensor pressure Min.: 0.00 Mpa, Max.: 23.28 Mpa Brake pedal depressed: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 Mpa
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Pressure
50003 105 393
OK:

Data List pressure is within standard range.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1422 is not output. A
DTC C1422 is output. B



A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C364228C16
1.479,0.104 1.906,0.375 0.427,0.271 2.708,1.823 2.208,1.313 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 2.635,1.854 3.094,2.052 0.458,0.198 10 false STP 0.177,0.177 0.635,0.375 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A86-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.
C239141C08
1.563,2.073 0.979,2.875 false 1.823,2.073 2.406,2.875 false 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 0.74,2.885 1.198,3.073 0.458,0.188 10 false FSW+ 2.26,2.906 2.719,3.094 0.458,0.188 10 false FSW-
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A55 or A56 brake pedal load sensing switch (brake pedal support assembly) connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Brake pedal load sensing switch off (Brake pedal depressed) 950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Brake pedal load sensing switch on (Brake pedal released) 203 to 223 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A86-23 (FSW+) - A56-2 (FSW+) Always Below 1 Ω
A86-23 (FSW+) or A56-2 (FSW+) - Body ground Always 10 kΩ or higher
A56-1 (FSW-) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A86-23 (FSW+) - A55-2 (FSW+) Always Below 1 Ω
A86-23 (FSW+) or A55-2 (FSW+) - Body ground Always 10 kΩ or higher
A55-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the brake pedal height and the stop light switch assembly has been installed properly.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT

OK:

The brake pedal height and the stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION