Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1415 and C1416.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1415

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH

·

Rear speed sensor circuit

·

Skid control ECU (brake actuator assembly)


C1408 Open or Short in Rear Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the +BS terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH

·

Rear speed sensor circuit

·

Skid control ECU (brake actuator assembly)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Sensor Voltage Open
RL Speed Sensor Voltage Open
50003 105 296,297
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

2.READ VALUE USING GTS (REAR SPEED SENSOR)

B

4.INSPECT SKID CONTROL SENSOR WIRE

C

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

e.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

3.RECONFIRM DTC

B

4.INSPECT SKID CONTROL SENSOR WIRE

C

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1407 and C1408 are not output. A
DTCs C1407 and/or C1408 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.INSPECT SKID CONTROL SENSOR WIRE
a.
C296046C01
0.844,2.667 1.167,2.833 0.323,0.167 0.854,0.333 1.177,0.5 0.323,0.167 2.344,0.583 2.667,0.75 0.323,0.167 2.219,2.833 2.542,3 0.323,0.167 0.5,1.833 0.5,1.5 0.5,1.5 0.906,1.135 false 0.5,4.25 0.5,3.833 0.5,3.833 0.917,3.448 false 2,1.833 2,1.583 2,1.583 2.302,1.333 false 1.917,4.25 1.917,3.917 1.917,3.917 2.167,3.615 false 1.583,1.833 1.583,1.5 1.583,1.5 1.156,1.135 false 1.5,4.25 1.5,3.833 1.5,3.833 1.177,3.448 false 3,1.833 3,1.583 3,1.583 2.698,1.344 false 2.917,4.25 2.917,3.917 2.917,3.917 2.635,3.604 false 1.49,1.865 1.948,2.063 0.458,0.198 10 false RR+ 1.917,1.865 2.375,2.063 0.458,0.198 10 false RR+ 2.917,1.875 3.375,2.073 0.458,0.198 10 false RR- 0.417,1.865 0.875,2.063 0.458,0.198 10 false RR- 0.427,4.292 0.885,4.49 0.458,0.198 10 false RL- 1.417,4.292 1.875,4.49 0.458,0.198 10 false RL+ 1.833,4.281 2.292,4.479 0.458,0.198 10 false RL+ 2.844,4.281 3.302,4.479 0.458,0.198 10 false RL- 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 0.958,0.333 1.271,0.531 0.313,0.198 10 false o1 2.281,2.844 2.594,3.042 0.313,0.198 10 false Or1 0.958,2.667 1.271,2.865 0.313,0.198 10 false r1 2.385,0.583 2.698,0.781 0.313,0.198 10 false Oo1 0.177,0.51 0.49,0.708 0.313,0.198 12 false *A 0.188,2.802 0.5,3 0.313,0.198 12 false *B 0.927,1.948 1.24,2.146 0.313,0.198 10 false *b 2.417,1.948 2.729,2.146 0.313,0.198 10 false *c 0.938,4.365 1.25,4.563 0.313,0.198 10 false *b 2.323,4.365 2.635,4.563 0.313,0.198 10 false *c
*A RH
*B LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Remove the skid control sensor wire.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
o1-2 (RR+) - Oo1-2 (RR+) Always Below 1 Ω
o1-2 (RR+) - Oo1-1 (RR-) Always 10 kΩ or higher
o1-2 (RR+) or Oo1-2 (RR+) - Body ground Always 10 kΩ or higher
o1-1 (RR-) - Oo1-1 (RR-) Always Below 1 Ω
o1-1 (RR-) - Oo1-2 (RR+) Always 10 kΩ or higher
o1-1 (RR-) or Oo1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
r1-2 (RL+) - Or1-3 (RL+) Always Below 1 Ω
r1-2 (RL+) - Or1-1 (RL-) Always 10 kΩ or higher
r1-2 (RL+) or Or1-3 (RL+) - Body ground Always 10 kΩ or higher
r1-1 (RL-) - Or1-1 (RL-) Always Below 1 Ω
r1-1 (RL-) - Or1-3 (RL+) Always 10 kΩ or higher
r1-1 (RL-) or Or1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-16 (RR+) - Oo1-2 (RR+) Always Below 1 Ω
A86-16 (RR+) or Oo1-2 (RR+) - Body ground Always 10 kΩ or higher
A86-15 (RR-) - Oo1-1 (RR-) Always Below 1 Ω
A86-15 (RR-) or Oo1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-29 (RL+) - Or1-3 (RL+) Always Below 1 Ω
A86-29 (RL+) or Or1-3 (RL+) - Body ground Always 10 kΩ or higher
A86-28 (RL-) - Or1-1 (RL-) Always Below 1 Ω
A86-28 (RL-) or Or1-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C205828C05
0.75,0.906 1.083,1.083 0.333,0.177 2.354,0.906 2.688,1.083 0.333,0.177 1.094,1.823 1.417,2.417 false 2.667,1.76 3,2.417 false 0.104,0.073 0.292,0.26 0.188,0.188 10 false *a 0.802,0.906 1.333,1.177 0.531,0.271 10 false Oo1 2.417,0.906 2.917,1.198 0.5,0.292 10 false Or1 1.323,2.469 1.656,2.656 0.333,0.188 10 false RR+ 2.917,2.469 3.25,2.656 0.333,0.188 10 false RL+ 0.25,0.729 0.646,1.073 0.396,0.344 12 false *A 1.917,0.729 2.26,1.188 0.344,0.458 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
Oo1-2 (RR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
Or1-3 (RL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

for 2WD: The rear speed sensor rotor and rear speed sensor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the O3 or O2 rear speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-16 (RR+) - O3-2 (RR+) Always Below 1 Ω
A86-16 (RR+) or O3-2 (RR+) - Body ground Always 10 kΩ or higher
A86-15 (RR-) - O3-1 (RR-) Always Below 1 Ω
A86-15 (RR-) or O3-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-29 (RL+) - O2-3 (RL+) Always Below 1 Ω
A86-29 (RL+) or O2-3 (RL+) - Body ground Always 10 kΩ or higher
A86-28 (RL-) - O2-1 (RL-) Always Below 1 Ω
A86-28 (RL-) or O2-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C205828C04
0.75,0.906 1.083,1.083 0.333,0.177 2.354,0.906 2.688,1.083 0.333,0.177 1.094,1.823 1.417,2.417 false 2.667,1.76 3,2.417 false 0.104,0.073 0.292,0.26 0.188,0.188 10 false *a 0.823,0.906 1.354,1.177 0.531,0.271 10 false O3 2.427,0.906 2.927,1.198 0.5,0.292 10 false O2 1.323,2.469 1.656,2.656 0.333,0.188 10 false RR+ 2.917,2.469 3.25,2.656 0.333,0.188 10 false RL+ 0.25,0.729 0.646,1.073 0.396,0.344 12 false *A 1.917,0.729 2.26,1.188 0.344,0.458 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
O3-2 (RR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
O2-3 (RL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG