Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1430  Brake Pedal Load Sensing Switch OFF Stuck Malfunction  C1431  Brake Pedal Load Sensing Switch ON Stuck Malfunction  


DESCRIPTION

The brake pedal load sensing switch (brake pedal support assembly) turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU (brake actuator assembly) uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction Either of the following is detected:
1.

With the stop light switch assembly on, the brake pedal load sensing switch off, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the deceleration is 0.4 G or more for 1 second or more.

2.

With the stop light switch assembly on, the brake pedal load sensing switch off, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (brake pedal support assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (brake actuator assembly)


C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction Either of the following is detected:
1.

Immediately after the ignition switch is turned to ON, the brake pedal load sensing switch is on and the stop light switch assembly is off for 10 seconds or more.

2.

The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (brake pedal support assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


HINT:

When C1425 and/or C1426 is output together with C1430 and/or C1431, inspect and repair the trouble areas indicated by C1425 and/or C1426 first.

for C1425: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425

for C1426: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 105 37,39

d.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



e.

Slowly depress the brake pedal, and check when the stop light switch assembly and brake pedal load sensing switch turn on.

OK:

First the stop light switch assembly should turn on, and then the brake pedal load sensing switch should turn on.



Result:
Result Proceed to
OK A
NG (Turning on of the brake pedal load sensing switch is not confirmed.) B
NG (The brake pedal load sensing switch turns on first.) C



A

2.RECONFIRM DTC

B

3.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

C

5.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1430 and C1431 are not output. A
DTCs C1430 and/or C1431 are output. B



A

B

3.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.
C239141C08
1.563,2.073 0.979,2.875 false 1.823,2.073 2.406,2.875 false 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 0.74,2.885 1.198,3.073 0.458,0.188 10 false FSW+ 2.26,2.906 2.719,3.094 0.458,0.188 10 false FSW-
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A55 or A56 brake pedal load sensing switch (brake pedal support assembly) connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Brake pedal load sensing switch off (Brake pedal depressed) 950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Brake pedal load sensing switch on (Brake pedal released) 203 to 223 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL SUPPORT ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A86-23 (FSW+) - A56-2 (FSW+) Always Below 1 Ω
A86-23 (FSW+) or A56-2 (FSW+) - Body ground Always 10 kΩ or higher
A56-1 (FSW-) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A86-23 (FSW+) - A55-2 (FSW+) Always Below 1 Ω
A86-23 (FSW+) or A55-2 (FSW+) - Body ground Always 10 kΩ or higher
A55-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION