Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Display Malfunction  


DESCRIPTION

FUEL RECEIVER GAUGE OPERATION


a.

OPERATION

The combination meter assembly uses the fuel sender gauge assembly and the fuel injection volume signal from the ECM to detect the amount of fuel remaining in the fuel tank assembly. There are 2 types of the fuel sender gauge assemblies available. One type detects the amount of fuel remaining using a variable resistor and other type detects the amount of fuel remaining using a Hall IC.

i.

Variable resistor type:

The fuel sender gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The fuel sender gauge assembly receives voltage from the combination meter assembly and changes the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank assembly. The combination meter assembly receives a fuel injection volume signal from the ECM and detects the voltage between the variable resistor and the resistor in the combination meter assembly, and operates the fuel receiver gauge.


ii.

Hall IC type:

The Hall IC built into the fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly detects the voltage output from the fuel sender gauge assembly, and operates the fuel receiver gauge.



b.

FUEL RECEIVER GAUGE READING

i.

During normal driving:

As the fuel level in the fuel tank assembly changes when driving on a hill or applying brakes, the fuel receiver gauge reading is updated according to the fuel injection volume during normal driving. However, as the fuel injection volume measurement has a margin of error, the value is indicated after correction by input values from the fuel sender gauge assembly.


ii.

During refueling:

The fuel level in the fuel tank assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the shift lever position and changes in the fuel level, output values from the fuel sender gauge assembly are immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



c.

REFUELING JUDGMENT CONDITIONS

NOTICE:

Add fuel with the ignition switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading is obtained. If it is necessary to add fuel with the ignition switch ON, move the shift lever to P or N.


i.

Normal judgment condition (When normal refueling method is used)

With the ignition switch off, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 lmp. qts) or more in the fuel level.


ii.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the ignition switch ON, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 lmp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in P or N, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 lmp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in any driving position, the fuel sender gauge assembly detects a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level.




d.

PRECAUTION FOR REFUELING

The fuel sender gauge assembly cannot detect changes in fuel level within certain ranges (around points E and F). Therefore, even though 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


e.

FORCED RESET OF FUEL RECEIVER GAUGE

When driving at 20 km/h (12 mph) or more, if the output value from the fuel sender gauge assembly is different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 2 minutes, the output value from the fuel sender gauge assembly is immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.



WIRING DIAGRAM

for 1AR-FE


E230580E50
5.26,3.104 7.146,3.333 1.885,0.229 10 false Combination Meter Assembly 5.719,0.979 5.99,1.135 0.271,0.156 10 false FR 5.719,2.344 6.125,2.5 0.406,0.156 10 false FE 5.552,0.885 6.01,1.271 0.458,0.385 10 false 4 5.469,2.229 5.823,2.573 0.354,0.344 10 false 23 2.323,2.229 2.438,2.375 0.115,0.146 10 false 3 2.323,0.885 2.438,1.031 0.115,0.146 10 false 2 0.365,3.104 4.479,3.281 4.115,0.177 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.781,1.448 1.219,1.615 0.438,0.167 10 false Fuel 2.031,2.229 2.281,2.406 0.25,0.177 10 false FE 2.042,0.885 2.344,1.177 0.302,0.292 10 false FS 5.26,2.948 5.771,3.281 0.51,0.333 10 false F126 0.365,2.948 1.042,3.302 0.677,0.354 10 false M9 1.698,2.01 1.813,2.156 0.115,0.146 10 false 1 1.688,1.354 1.802,1.5 0.115,0.146 10 false 2 0.771,1.625 1.313,1.802 0.542,0.177 10 false Sender 0.771,1.792 1.271,2 0.5,0.208 10 false Gauge 0.771,1.948 1.49,2.146 0.719,0.198 10 false Assembly 0.781,1.271 1.083,1.563 0.302,0.292 10 false A


for 2GR-FKS


E285369E15
0.417,2.833 0.75,3 0.333,0.167 10 false M49 0.417,3 3.583,3.167 3.167,0.167 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.25,2.833 5.625,3.042 0.375,0.208 10 false F126 5.25,3 7.083,3.167 1.833,0.167 10 false Combination Meter Assembly 0.781,1.479 1.25,1.667 0.469,0.188 10 false Sender 1.688,1.188 1.833,1.354 0.146,0.167 10 false 1 1.688,1.844 1.833,2.01 0.146,0.167 10 false 2 2.333,0.74 2.479,0.906 0.146,0.167 10 false 3 2.333,1.406 2.479,1.573 0.146,0.167 10 false 1 2.323,2.083 2.469,2.25 0.146,0.167 10 false 2 2.021,2.083 2.271,2.25 0.25,0.167 10 false FE 2.042,1.406 2.292,1.573 0.25,0.167 10 false FV 2.125,0.74 2.375,0.906 0.25,0.167 10 false S 5.531,0.74 5.781,0.906 0.25,0.167 10 false 4 5.542,1.406 5.792,1.573 0.25,0.167 10 false 3 5.469,2.083 5.719,2.25 0.25,0.167 10 false 23 5.74,0.833 6.156,1.135 0.417,0.302 10 false FR 5.74,1.5 5.99,1.667 0.25,0.167 10 false FV 5.74,2.167 6.031,2.375 0.292,0.208 10 false FE 0.781,1.313 1.094,1.49 0.313,0.177 10 false Fuel 0.781,1.646 1.229,1.854 0.448,0.208 10 false Gauge 0.781,1.813 1.417,2 0.635,0.188 10 false Assembly 1.823,1.417 1.969,1.583 0.146,0.167 10 false 3 0.802,1.125 0.948,1.292 0.146,0.167 10 false A


CAUTION / NOTICE / HINT

HINT:

The fuel level warning light will come on when the fuel level is below 10.7 liters (11.3 US qts, 9.4 Imp. qts).


PROCEDURE

1.CHECK SYMPTOMS
a.

Ask the customer about the problem symptoms.


Result:
Result Proceed to
Malfunction occurs when adding fuel (Even after adding fuel, reading does not increase at all or increases very slowly, etc.) A
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) B
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) C



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

11.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

C

16.CHECK FOR DTC
2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK FOR DTC
a.

Check if SFI System DTCs are output.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B



A

4.CHECK FOR DTC

B

4.CHECK FOR DTC
a.

Check if Vehicle Stability Control System DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

B

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
a.

Record the fuel receiver gauge reading.


b.

If the fuel tank assembly is almost full, drain 20 liters or more of fuel. (This is not necessary when the fuel tank assembly is sufficiently below full.)


c.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



d.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


e.

Check that the fuel receiver gauge has been reset.


f.

Drive the vehicle at 1.75 km/h or more, then move the shift lever to P and turn the ignition switch off.


g.

Add 5.0 liters or more of fuel, turn the ignition switch to ON, and check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.


Result:
Result Proceed to
Fuel receiver gauge reading increases in proportion to the amount of fuel added A
Fuel receiver gauge reading does not change even when fuel is added B



A

6.INSPECT FUEL TANK ASSEMBLY

B

7.READ VALUE USING GTS (FUEL INPUT)
6.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal B
There is an excessive amount of foreign matter in the fuel tank assembly C
The fuel tank assembly or fuel sender gauge assembly is not installed correctly D



A

7.READ VALUE USING GTS (FUEL INPUT)

B

REPLACE FUEL TANK ASSEMBLY

C

CLEAN INSIDE OF FUEL TANK ASSEMBLY

D

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY

7.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 64.8 L
Fuel receiver gauge indicates 3/4: 51.6 L
Fuel receiver gauge indicates 1/2: 36.0 L
Fuel receiver gauge indicates 1/4: 20.4 L
Fuel receiver gauge indicates E: 7.2 L
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication B



A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

for 1AR-FE

i.

Disconnect the F126 combination meter assembly connector.


ii.

Disconnect the M9 fuel suction tube with pump and gauge assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-2 (FS) - F126-4 (FR) Always Below 1 Ω
M9-3 (FE) - F126-23 (FE) Always Below 1 Ω
M9-2 (FS) or F126-4 (FR) - Body ground Always 10 kΩ or higher
M9-3 (FE) or F126-23 (FE) - Body ground Always 10 kΩ or higher




b.

for 2GR-FKS

i.

Disconnect the F126 combination meter assembly connector.


ii.

Disconnect the M49 fuel suction tube with pump and gauge assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-3 (S) - F126-4 (FR) Always Below 1 Ω
M49-2 (FE) - F126-23 (FE) Always Below 1 Ω
M49-1 (FV) - F126-3 (FV) Always Below 1 Ω
M49-3 (S) or F126-4 (FR) - Body ground Always 10 kΩ or higher
M49-2 (FE) or F126-23 (FE) - Body ground Always 10 kΩ or higher
M49-1 (FV) or F126-3 (FV) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FUEL SENDER GAUGE ASSEMBLY

b.

Inspect the fuel sender gauge assembly.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION

OK:

Fuel sender gauge assembly is normal.



Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

10.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E158805C65
0.229,1.458 0.656,1.76 0.427,0.302 0.313,3.667 0.729,3.958 0.417,0.292 0.229,1 0.656,1.302 0.427,0.302 1.406,1.198 1.156,0.74 false 1.802,1.219 1.802,0.708 false 2.104,1.208 2.365,0.802 false 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.344,1.063 0.677,1.313 0.333,0.25 10 false M9 0.458,3.74 0.792,3.99 0.333,0.25 10 false A 1.448,0.5 2.198,0.708 0.75,0.208 10 false FS*A, S*B 1.021,0.563 1.354,0.813 0.333,0.25 10 false FE 2.229,0.615 2.885,0.844 0.656,0.229 10 false FV*B 0.313,1.531 0.646,1.781 0.333,0.25 10 false M49 0.74,1.063 1.073,1.313 0.333,0.25 10 false *A 0.74,1.521 1.073,1.771 0.333,0.25 10 false *B
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)
*A for 1AR-FE
*B for 2GR-FKS


a.

for 1AR-FE

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-2 (FS) - A-2 Always Below 1 Ω
M9-3 (FE) - A-1 Always Below 1 Ω




b.

for 2GR-FKS

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (FV) - A-3 Always Below 1 Ω
M49-2 (FE) - A-2 Always Below 1 Ω
M49-3 (S) - A-1 Always Below 1 Ω




c.

Measure the resistance according to the value(s) in the table below.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

11.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

12.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

12.CHECK FOR DTC
a.

Check if SFI System DTCs are output.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B



A

13.CHECK FOR DTC

B

13.CHECK FOR DTC
a.

Check if Vehicle Stability Control System DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

14.CHECK FOR DTC

B

14.CHECK FOR DTC
a.

Check if Meter / Gauge System DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTC B1500 is not output A
DTC B1500 is output B



A

15.INSPECT FUEL RECEIVER GAUGE

B

15.INSPECT FUEL RECEIVER GAUGE
a.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



b.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


c.

Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly.


Result:
Result Proceed to
Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly A
Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank assembly B



A

END

B

7.READ VALUE USING GTS (FUEL INPUT)
16.CHECK FOR DTC
a.

Check if SFI System DTCs are output.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B



A

17.CHECK FOR DTC

B

17.CHECK FOR DTC
a.

Check if Vehicle Stability Control System DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

18.INSPECT FUEL TANK ASSEMBLY

B

18.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal B
There is an excessive amount of foreign matter in the fuel tank assembly C
The fuel tank assembly or fuel sender gauge assembly is not installed correctly D



A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE FUEL TANK ASSEMBLY

C

CLEAN INSIDE OF FUEL TANK ASSEMBLY

D

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY