In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM via the CAN communication system. The combination meter assembly displays the engine coolant temperature that is calculated based on the data received from the ECM.
Before replacing the ECM, refer to Service Bulletin.*
*: w/ Smart Entry and Start System
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores DTCs. Troubleshoot the SFI System.
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output | A |
| CAN communication DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Water Temperature Meter Operation | Engine coolant temperature receiver gauge | OFF, LOW, NORMAL or HIGH | - |
| Tester Display |
|---|
| Water Temperature Meter Operation |
Engine coolant temperature receiver gauge indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up engine | - |
| Tester Display |
|---|
| Coolant Temperature |
Engine coolant temperature displayed on the GTS is almost the same as the engine coolant temperature receiver gauge indication.
When the data list values and engine coolant temperature receiver gauge values match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
When the data list values and engine coolant temperature receiver gauge values do not match, an internal malfunction of the combination meter assembly is suspected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if SFI System DTCs are output.
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| SFI system DTCs are not output | A |
| SFI system DTCs are output | B |
A
B
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus:
for Engine (for 1AR-FE): Powertrain / Engine and ECT / Data List.
for Engine (for 2GR-FKS): Powertrain / Engine / Data List.
for Combination Meter: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
Engine (for 1AR-FE)
| Tester Display | Measurement Item | Range | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|---|
| Coolant Temp | Engine coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up engine | - | This is the engine coolant temperature.
|
| Tester Display |
|---|
| Coolant Temp |
Engine (for 2GR-FKS)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Tester Display |
|---|
| Coolant Temperature |
Combination Meter
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up engine | - |
| Tester Display |
|---|
| Coolant Temperature |
| Result | Proceed to |
|---|---|
| The data list values of the ECUs match | A |
| The data list values of the ECUs do not match | B |
When the data list values of the ECUs match, an internal malfunction of the ECM is suspected.
When the data list values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
A
B
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
Replace the combination meter assembly with a new or known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
The operation of the engine coolant temperature receiver gauge returns to normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL