Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1403  Rear Speed Sensor RH Malfunction  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

Refer to DTCs C1415 and C1416.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1415

DTC No. Detection Item DTC Detection Condition Trouble Area
C1403 Rear Speed Sensor RH Malfunction Any of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more (for 2WD).

2.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more (for AWD).

3.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

4.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more (for 2WD).

5.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more (for AWD).


·

Sensor installation

·

for 2WD: Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

for AWD: Rear speed sensor RH

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)


C1404 Rear Speed Sensor LH Malfunction Any of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more (for 2WD).

2.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more (for AWD).

3.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

4.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more (for 2WD).

5.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more (for AWD).


·

Sensor installation

·

for 2WD: Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

for AWD: Rear speed sensor LH

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)



HINT:

Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:

1.

Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

2.

Clear the DTCs.



HINT:
·

DTC C1403 is for the rear speed sensor RH.

·

DTC C1404 is for the rear speed sensor LH.



PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.
C116638C05
0.979,0.875 1.271,0.531 false 1.073,3.229 1.26,2.99 false 0.958,3.927 1.25,4.188 false 0.177,2.844 0.698,3.031 0.521,0.188 12 false *B 0.885,2.25 1.75,2.49 0.865,0.24 10 false *a 2.344,2.25 2.948,2.521 0.604,0.271 10 false *b 0.885,4.417 1.75,4.656 0.865,0.24 10 false *a 2.49,4.417 3.094,4.583 0.604,0.167 10 false *b 0.167,0.531 0.688,0.719 0.521,0.188 12 false *A 0.177,0.083 0.49,0.281 0.313,0.198 10 false *1 1.323,0.438 2.188,0.677 0.865,0.24 10 false *d 1.313,2.885 2.177,3.125 0.865,0.24 10 false *c 1.313,4.198 2.177,4.438 0.865,0.24 10 false *d
*A for 2WD
*B for AWD
*1 Rear Speed Sensor
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Result Proceed to
OK (for AWD) A
OK (for 2WD) B
NG C



A

2.CHECK REAR SPEED SENSOR AND SENSOR ROTOR

B

3.READ VALUE USING GTS (REAR SPEED SENSOR)

C

2.CHECK REAR SPEED SENSOR AND SENSOR ROTOR
a.

Remove the rear speed sensor and the component with the sensor rotor.

for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for AWD)>REMOVAL

for sensor rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

3.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Install the rear speed sensor and the component with the sensor rotor (for AWD).


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

e.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


Result:
Result Proceed to
NG (for AWD) A
NG (for 2WD) B
OK C


HINT:
·

for 2WD: The rear speed sensor rotor and rear speed sensor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.





A

4.REPLACE REAR SPEED SENSOR

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

C

4.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1403 and C1404 are not output. A
DTCs C1403 and/or C1404 are output. B


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

for AWD: The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE





A

END

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY