Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Main Body ECU)  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 1.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to sub bus 1, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to sub bus 1. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to sub bus 1 when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 1, the main body ECU (multiplex network body ECU) determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module (Main Body ECU) The main body ECU (multiplex network body ECU) cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1.
·

Open or short in sub bus 1 main line or connector

·

Open or short in sub bus 1 branch line or connector

·

Main body ECU (multiplex network body ECU)

·

Outer mirror control ECU assembly (for driver side)

(w/ Seat position memory system)

·

Outer mirror control ECU assembly (for front passenger side)

(w/ Seat position memory system)

·

Position control ECU and switch assembly

(w/ Seat position memory system)

·

Multiplex network door ECU

(w/ Power back door system)

·

Open or short in No. 5 CAN junction connector

·

Open or short in No. 6 CAN junction connector


HINT:

The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.



HINT:

This diagnosis procedure is for when DTC U1002 is output by the main body ECU (multiplex network body ECU) (GTS display: Main Body).


WIRING DIAGRAM

C365944E01
0.115,0.135 1.938,0.74 1.823,0.604 12 false Sub Bus 1 (for LHD): 0.063,0.76 2.667,1.135 2.604,0.375 10 false *1: w/ Seat Position Memory System 0.073,1.125 2.302,1.49 2.229,0.365 10 false *2: w/ Power Back Door System 5.802,0.052 7.073,0.542 1.271,0.49 10 false x: Suspected Area 4.25,0.875 4.833,1.125 0.583,0.25 10 false CANP 3.594,0.5 4.177,0.75 0.583,0.25 10 false 120 Ω 2.906,0.865 3.49,1.115 0.583,0.25 10 false CANN 4.813,0.646 5.125,0.906 0.313,0.26 10 false F18 5.146,0.635 6.844,1.125 1.698,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 4.25,1.177 4.51,1.438 0.26,0.26 10 false 9 3.135,1.177 3.396,1.438 0.26,0.26 10 false 10 3.125,1.479 3.385,1.74 0.26,0.26 10 false W 4.26,1.469 4.521,1.729 0.26,0.26 10 false G 3.146,1.885 3.406,2.146 0.26,0.26 10 false 13 4.229,1.865 4.49,2.125 0.26,0.26 10 false 2 4.5,2.604 4.76,2.865 0.26,0.26 10 false 3 4.51,3.208 4.771,3.469 0.26,0.26 10 false 14 4.813,3.26 5.073,3.521 0.26,0.26 10 false W 5.438,3.271 5.698,3.531 0.26,0.26 10 false V 4.792,2.521 5.083,2.792 0.292,0.271 10 false LG 5.406,2.521 5.698,2.792 0.292,0.271 10 false SB 5.75,2.594 6.01,2.854 0.26,0.26 10 false 9 5.74,3.208 6,3.469 0.26,0.26 10 false 8 5.927,2.604 6.51,2.854 0.583,0.25 10 false CANP 5.927,3.208 6.51,3.458 0.583,0.25 10 false CANN 5.625,3.5 5.938,3.76 0.313,0.26 10 false H2 5.865,3.5 7.115,4.313 1.25,0.813 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side)*1 0.594,2.76 0.958,3.052 0.365,0.292 10 false F112 1.021,2.76 2.99,3.167 1.969,0.406 10 false No. 6 CAN Junction Connector 3.146,3.563 3.406,3.823 0.26,0.26 10 false 16 4.198,3.573 4.458,3.833 0.26,0.26 10 false 5 3.125,3.885 3.385,4.146 0.26,0.26 10 false W 4.26,3.875 4.521,4.135 0.26,0.26 10 false B 3.167,4.177 3.427,4.438 0.26,0.26 10 false 16 4.208,4.146 4.469,4.406 0.26,0.26 10 false 5 2.875,4.438 3.135,4.698 0.26,0.26 10 false 3 2.813,5.021 3.073,5.281 0.26,0.26 10 false 14 2.313,5.115 2.573,5.375 0.26,0.26 10 false W 2.333,4.354 2.594,4.615 0.26,0.26 10 false P 1.76,4.344 2.021,4.604 0.26,0.26 10 false L 1.719,5.115 1.979,5.375 0.26,0.26 10 false W 1.26,4.427 1.521,4.688 0.26,0.26 10 false 8 1.26,5.052 1.521,5.313 0.26,0.26 10 false 7 0.781,4.427 1.365,4.677 0.583,0.25 10 false CANP 0.781,5.021 1.365,5.271 0.583,0.25 10 false CANN 0.063,5.344 0.302,5.635 0.24,0.292 10 false e7 0.292,5.344 1.865,6.01 1.573,0.667 10 false Position Control ECU and Switch Assembly*1 4.542,4.677 4.906,4.969 0.365,0.292 10 false F111 4.948,4.667 6.917,5.073 1.969,0.406 10 false No. 5 CAN Junction Connector 4.521,5.448 4.781,5.708 0.26,0.26 10 false 4 4.51,6.042 4.771,6.302 0.26,0.26 10 false 15 5.104,6.104 5.365,6.365 0.26,0.26 10 false P 5.042,5.365 5.333,5.635 0.292,0.271 10 false SB 5.75,5.448 6.01,5.708 0.26,0.26 10 false 9 5.74,6.042 6,6.302 0.26,0.26 10 false 8 5.948,6.042 6.531,6.292 0.583,0.25 10 false CANN 5.938,5.458 6.521,5.708 0.583,0.25 10 false CANP 5.656,6.323 5.969,6.583 0.313,0.26 10 false I2 5.865,6.323 7.135,7.135 1.271,0.813 10 false Outer Mirror Control ECU Assembly (for Driver Side)*1 4.208,6.302 4.469,6.563 0.26,0.26 10 false 1 3.167,6.292 3.427,6.552 0.26,0.26 10 false 12 3.135,6.531 3.396,6.792 0.26,0.26 10 false W 4.271,6.51 4.531,6.771 0.26,0.26 10 false L 3.177,6.771 3.438,7.031 0.26,0.26 10 false 14 4.177,6.771 4.438,7.031 0.26,0.26 10 false 13 2.917,7.021 3.5,7.271 0.583,0.25 10 false CANN 4.24,7.01 4.823,7.26 0.583,0.25 10 false CANP 3.604,7.438 4.188,7.688 0.583,0.25 10 false 120 Ω 0.906,7.271 2.875,7.885 1.969,0.615 10 false Multiplex Network Door ECU*2 0.656,7.271 0.896,7.563 0.24,0.292 10 false X6 0.792,8.021 2.76,8.344 1.969,0.323 10 false : CAN Main Bus Line (CANH) 0.802,8.406 2.802,8.719 2,0.313 10 false : CAN Main Bus Line (CANL) 3.948,8.031 5.917,8.354 1.969,0.323 10 false : CAN Branch Line (CANH) 3.948,8.417 5.917,8.74 1.969,0.323 10 false : CAN Branch Line (CANL)

C365945E01
0.083,0.083 1.792,0.542 1.708,0.458 12 false Sub Bus 1 (for RHD): 5.813,0.073 7.094,0.604 1.281,0.531 10 false x: Suspected Area 3.583,0.51 4.281,0.74 0.698,0.229 10 false 120 Ω 2.917,0.917 3.531,1.115 0.615,0.198 10 false CANN 4.271,0.917 4.885,1.115 0.615,0.198 10 false CANP 4.76,0.573 5.083,0.823 0.323,0.25 10 false F18 5.125,0.563 6.813,1.135 1.688,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 3.167,1.177 3.479,1.406 0.313,0.229 10 false 10 4.198,1.177 4.51,1.406 0.313,0.229 10 false 9 3.135,1.469 3.448,1.698 0.313,0.229 10 false W 4.25,1.479 4.563,1.708 0.313,0.229 10 false G 3.177,1.875 3.49,2.104 0.313,0.229 10 false 13 4.208,1.875 4.521,2.104 0.313,0.229 10 false 2 0.094,0.719 2.438,1.01 2.344,0.292 10 false *1: w/ Seat Position Memory System 0.104,1.042 2.448,1.333 2.344,0.292 10 false *2: w/ Power Back Door System 0.792,2.146 1.406,2.344 0.615,0.198 10 false CANP 0.781,2.729 1.396,2.927 0.615,0.198 10 false CANN 1.229,2.156 1.542,2.385 0.313,0.229 10 false 8 1.24,2.729 1.552,2.958 0.313,0.229 10 false 7 1.813,2.094 2.125,2.323 0.313,0.229 10 false L 2.427,2.104 2.74,2.333 0.313,0.229 10 false P 1.771,2.802 2.083,3.031 0.313,0.229 10 false W 2.385,2.792 2.698,3.021 0.313,0.229 10 false W 0.094,3.042 0.417,3.292 0.323,0.25 10 false d7 0.333,3.031 2.01,3.583 1.677,0.552 10 false Position Control ECU and Switch Assembly*1 2.927,2.167 3.24,2.396 0.313,0.229 10 false 4 2.875,2.74 3.188,2.969 0.313,0.229 10 false 15 4.531,2.323 4.927,2.615 0.396,0.292 10 false F112 4.948,2.323 6.917,2.802 1.969,0.479 10 false No. 6 CAN Junction Connector 5.938,3.125 6.552,3.323 0.615,0.198 10 false CANP 5.927,3.719 6.542,3.917 0.615,0.198 10 false CANN 4.5,3.156 4.813,3.385 0.313,0.229 10 false 3 4.479,3.719 4.792,3.948 0.313,0.229 10 false 14 4.792,3.073 5.104,3.302 0.313,0.229 10 false LG 5.396,3.083 5.708,3.313 0.313,0.229 10 false SB 4.813,3.771 5.125,4 0.313,0.229 10 false W 5.448,3.771 5.76,4 0.313,0.229 10 false V 5.76,3.135 6.073,3.365 0.313,0.229 10 false 9 5.75,3.719 6.063,3.948 0.313,0.229 10 false 8 5.604,4.01 5.927,4.26 0.323,0.25 10 false H2 5.875,4 7.135,4.594 1.26,0.594 10 false Outer Mirror Control ECU Assembly (for Driver Side)*1 3.188,3.969 3.5,4.198 0.313,0.229 10 false 16 4.208,3.979 4.521,4.208 0.313,0.229 10 false 5 3.146,4.354 3.458,4.583 0.313,0.229 10 false W 4.24,4.344 4.552,4.573 0.313,0.229 10 false B 3.177,4.75 3.49,4.979 0.313,0.229 10 false 16 4.208,4.74 4.521,4.969 0.313,0.229 10 false 5 0.563,5.427 1.135,5.802 0.573,0.375 10 false F111 0.99,5.427 2.958,5.906 1.969,0.479 10 false No. 5 CAN Junction Connector 4.51,5.448 4.823,5.677 0.313,0.229 10 false 4 4.5,6.052 4.813,6.281 0.313,0.229 10 false 15 5.146,6.094 5.458,6.323 0.313,0.229 10 false P 5.094,5.385 5.406,5.615 0.313,0.229 10 false SB 5.729,5.448 6.042,5.677 0.313,0.229 10 false 9 5.74,6.052 6.052,6.281 0.313,0.229 10 false 8 5.938,5.427 6.552,5.625 0.615,0.198 10 false CANP 5.948,6.052 6.563,6.25 0.615,0.198 10 false CANN 5.885,6.313 7.156,7.083 1.271,0.771 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side)*1 5.656,6.323 5.979,6.573 0.323,0.25 10 false I2 3.156,6.271 3.469,6.5 0.313,0.229 10 false 12 4.188,6.281 4.5,6.51 0.313,0.229 10 false 1 3.135,6.521 3.448,6.75 0.313,0.229 10 false W 4.229,6.531 4.542,6.76 0.313,0.229 10 false L 4.198,6.802 4.51,7.031 0.313,0.229 10 false 13 3.177,6.792 3.49,7.021 0.313,0.229 10 false 14 2.927,7 3.542,7.198 0.615,0.198 10 false CANN 4.229,7.01 4.844,7.208 0.615,0.198 10 false CANP 3.573,7.396 4.271,7.625 0.698,0.229 10 false 120 Ω 0.604,7.323 1.177,7.698 0.573,0.375 10 false X6 0.854,7.313 2.823,7.792 1.969,0.479 10 false Multiplex Network Door ECU*2 0.813,8.021 2.833,8.313 2.021,0.292 10 false : CAN Main Bus Line (CANH) 0.813,8.406 2.833,8.698 2.021,0.292 10 false : CAN Main Bus Line (CANL) 3.969,8.031 5.99,8.323 2.021,0.292 10 false : CAN Branch Line (CANH) 3.969,8.417 5.99,8.708 2.021,0.292 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*

*: w/ Smart Entry and Start System




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result:
Result Proceed to
for LHD A
for RHD B




A

2.CHECK SUB BUS 1

B

17.CHECK SUB BUS 1
2.CHECK SUB BUS 1
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C287224C06
1.51,2.469 1.938,2.76 0.427,0.292 1.5,0.292 1.906,0.573 0.406,0.281 1.25,1.948 1.375,1.948 1.375,1.948 1.813,1.188 true 2.375,1.938 2.26,1.938 2.26,1.938 1.906,1.188 true 1.635,3.104 0.958,2.708 0.958,2.708 0.75,2.708 true 1.865,4.063 2.031,4.063 2.031,4.063 2.344,3.635 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.073,2.427 0.385,2.625 0.313,0.198 10 false *1 1.604,2.521 1.917,2.719 0.313,0.198 10 false F25 1.594,0.323 1.906,0.521 0.313,0.198 10 false F18 0.813,1.854 1.427,2.052 0.615,0.198 10 false CANN 2.438,1.844 3.052,2.042 0.615,0.198 10 false CANP 0.51,2.615 0.823,2.813 0.313,0.198 10 false CG 1.563,3.969 2.021,4.167 0.458,0.198 10 false BAT
*1 DLC3
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus line
F18-9 (CANP) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F18-10 (CANN) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F18-9 (CANP) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F18-10 (CANN) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

3.CHECK FOR DTC OUTPUT

B

4.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

8.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

13.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON.


h.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC U1002 not output from main body ECU (multiplex network body ECU) (GTS display: Main Body) A
DTC U1002 is output from main body ECU (multiplex network body ECU) (GTS display: Main Body) B



A

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.
C285508C12
1.396,0.167 1.813,0.417 0.417,0.25 1.469,1.302 1.094,0.542 1.094,0.542 0.844,0.542 true 1.563,1.302 1.771,0.542 1.771,0.542 2.021,0.542 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.438,0.438 1.052,0.635 0.615,0.198 10 false CANP 2.073,0.438 2.688,0.635 0.615,0.198 10 false CANN 1.479,0.198 2.094,0.396 0.615,0.198 10 false F18
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

5.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
5.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
a.

Reconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.
C292400C02
1.5,0.281 1.938,0.563 0.438,0.281 0.573,1.854 0.646,1.854 0.646,1.854 0.76,1.427 true 1.083,1.854 1.01,1.854 1.01,1.854 0.885,1.438 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 1.646,0.323 2.104,0.521 0.458,0.198 10 false X6 0.156,1.75 0.771,1.948 0.615,0.198 10 false CANP 1.146,1.75 1.76,1.948 0.615,0.198 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

6.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the X6 multiplex network door ECU connector.


b.

Disconnect the F112 No. 6 CAN junction connector.


c.
C292406C01
1.5,0.313 1.958,0.635 0.458,0.323 1.104,1.99 1.01,0.885 1.01,0.885 0.823,0.885 true 1.115,2.26 0.99,2.729 0.99,2.729 0.865,2.729 true 1.573,1.958 2.177,0.875 2.177,0.875 2.333,0.875 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.25,0.781 1.167,0.979 0.917,0.198 10 false CANH*b 0.281,2.635 1.198,2.833 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*c 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*c 1.573,0.375 1.99,0.573 0.417,0.198 10 false F112
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to No. 5 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F112-2 (CANH) - F112-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
F112-5 (CANH) - F112-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector



Result:
Result Proceed to
OK A
NG (Main body ECU (multiplex network body ECU) main line) B
NG (No. 5 CAN junction connector main line) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

7.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F111 No. 5 CAN junction connector.


c.
C292406C02
1.5,0.313 1.958,0.635 0.458,0.323 0.948,1.99 0.844,0.865 0.844,0.865 0.75,0.865 true 0.958,2.26 0.906,2.708 0.906,2.708 0.802,2.708 true 1.573,1.958 2.177,0.875 2.177,0.875 2.333,0.875 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.188,0.76 1.104,0.958 0.917,0.198 10 false CANH*b 0.26,2.615 1.177,2.813 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*c 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*c 1.583,0.365 1.969,0.594 0.385,0.229 10 false F111
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
*c to No. 6 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F111-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Multiplex network door ECU
F111-5 (CANH) - F111-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector main line) B
NG (Multiplex network door ECU main line) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

8.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.
C285508C13
1.396,0.167 1.813,0.417 0.417,0.25 1.469,1.302 1.094,0.542 1.094,0.542 0.844,0.542 true 1.563,1.302 1.771,0.542 1.771,0.542 2.021,0.542 true 0.104,0.052 0.417,0.208 0.313,0.156 10 false *a 0.427,0.448 1.042,0.646 0.615,0.198 10 false CANP 2.073,0.448 2.688,0.646 0.615,0.198 10 false CANN 1.49,0.198 2.104,0.396 0.615,0.198 10 false F18
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

9.CHECK FOR SHORT IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
9.CHECK FOR SHORT IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
a.

Reconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.
C292400C03
1.5,0.281 1.938,0.563 0.438,0.281 0.573,1.854 0.646,1.854 0.646,1.854 0.76,1.427 true 1.083,1.854 1.01,1.854 1.01,1.854 0.885,1.438 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 1.635,0.323 2.094,0.521 0.458,0.198 10 false X6 0.156,1.75 0.771,1.948 0.615,0.198 10 false CANP 1.146,1.75 1.76,1.948 0.615,0.198 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

10.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
10.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the X6 multiplex network door ECU connector.


b.

Disconnect the F112 No. 6 CAN junction connector.


c.
C292406C03
1.5,0.313 1.958,0.635 0.458,0.323 1.104,1.99 1.01,0.885 1.01,0.885 0.823,0.885 true 1.115,2.26 0.99,2.729 0.99,2.729 0.865,2.729 true 1.573,1.958 2.177,0.875 2.177,0.875 2.333,0.875 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 1.25,1.958 1.135,0.635 1.135,0.635 1.021,0.635 true 1.271,2.26 1.177,3.063 1.177,3.063 1.063,3.063 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.25,0.781 1.167,0.979 0.917,0.198 10 false CANH*b 0.281,2.635 1.198,2.833 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*d 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*d 1.583,0.375 2,0.573 0.417,0.198 10 false F112 0.448,0.542 1.365,0.74 0.917,0.198 10 false CANH*c 0.521,2.969 1.438,3.167 0.917,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
*d to No. 5 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F112-2 (CANH) - F112-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
F112-3 (CANH) - F112-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly (for front passenger side)*
F112-5 (CANH) - F112-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector


*: w/ Seat Position Memory System


Result:
Result Proceed to
OK A
NG (Main body ECU (multiplex network body ECU) main line) B
NG (ECU or sensor branch line) C
NG (No. 5 CAN junction connector main line) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

12.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)

D

11.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F111 No. 5 CAN junction connector.


c.
C292406C04
1.5,0.313 1.958,0.635 0.458,0.323 0.948,1.99 0.844,0.865 0.844,0.865 0.75,0.865 true 0.958,2.26 0.906,2.708 0.906,2.708 0.802,2.708 true 1.573,1.958 2.177,0.875 2.177,0.875 2.333,0.875 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 1.25,1.969 0.958,0.594 0.958,0.594 0.823,0.594 true 1.26,2.26 1.094,2.938 1.094,2.938 0.979,2.938 true 1.427,1.969 1.135,0.365 1.135,0.365 1,0.365 true 1.417,2.25 1.208,3.135 1.208,3.135 1.104,3.135 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.188,0.76 1.104,0.958 0.917,0.198 10 false CANH*b 0.26,2.615 1.177,2.813 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*e 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*e 1.583,0.365 1.979,0.573 0.396,0.208 10 false F111 0.448,0.26 1.365,0.458 0.917,0.198 10 false CANH*d 0.26,0.5 1.177,0.698 0.917,0.198 10 false CANH*c 0.438,2.844 1.354,3.042 0.917,0.198 10 false CANL*c 0.583,3.042 1.5,3.24 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
*c to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
*d to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
*e to No. 6 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F111-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Multiplex network door ECU*1
F111-3 (CANH) - F111-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Position control ECU and switch assembly*2
F111-4 (CANH) - F111-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly (for driver side)*2
F111-5 (CANH) - F111-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector


·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (Multiplex network door ECU main line) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

12.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

12.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C295269C01
1.521,0.125 1.927,0.438 0.406,0.313 0.927,1.74 1.094,1.74 1.094,1.74 1.802,0.885 true 2.49,1.74 2.385,1.74 2.385,1.74 1.896,0.885 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.604,0.188 1.938,0.406 0.333,0.219 10 false F18 0.49,1.625 1.104,1.823 0.615,0.198 10 false CANN 2.573,1.646 3.188,1.844 0.615,0.198 10 false CANP
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU SENSOR BUS LINES OR CONNECTOR

13.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the F112 No. 6 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C295270C01
1.635,0.198 2.031,0.5 0.396,0.302 4.979,0.198 5.375,0.5 0.396,0.302 1.354,1.667 0.969,1.281 0.969,1.281 0.833,1.281 true 1.458,1.667 1.063,0.979 1.063,0.979 0.927,0.979 true 1.729,1.677 2.385,0.688 2.385,0.688 2.49,0.688 true 1.354,1.896 1.052,2.177 1.052,2.177 0.938,2.177 true 1.479,1.885 1.333,2.479 1.333,2.479 1.219,2.479 true 1.74,1.896 2.219,2.49 2.219,2.49 2.333,2.49 true 5.146,1.208 5.469,0.771 5.469,0.771 5.604,0.771 true 5.875,1.729 5.604,2.271 5.604,2.271 5.438,2.271 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 3.844,0.177 4.156,0.375 0.313,0.198 10 false *1 1.688,0.24 2.083,0.5 0.396,0.26 10 false F112 0.26,1.188 1.177,1.385 0.917,0.198 10 false CANH*b 0.365,0.875 1.281,1.073 0.917,0.198 10 false CANH*c 2.563,0.583 3.479,0.781 0.917,0.198 10 false CANH*d 0.698,2.385 1.615,2.583 0.917,0.198 10 false CANL*c 0.396,2.073 1.313,2.271 0.917,0.198 10 false CANL*b 2.406,2.385 3.323,2.583 0.917,0.198 10 false CANL*d 5.063,0.25 5.375,0.448 0.313,0.198 10 false F25 5.688,0.677 6,0.875 0.313,0.198 10 false CG 5.115,2.167 5.573,2.365 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
*d to No. 5 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
F112-2 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Main body ECU (multiplex network body ECU)
F112-13 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Outer mirror control ECU assembly (for front passenger side)*
F112-14 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-5 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short No. 5 CAN junction connector
F112-16 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-2 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Main body ECU (multiplex network body ECU)
F112-13 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F112-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Outer mirror control ECU assembly (for front passenger side)*
F112-14 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F112-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short No. 5 CAN junction connector
F112-16 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Seat Position Memory System

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result Proceed to
OK A
NG (Main body ECU (multiplex network body ECU) main line) B
NG (ECU or sensor bus line) C
NG (No. 5 CAN junction connector main line) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

14.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

16.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)

D

15.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 5 CAN JUNCTION CONNECTOR)
14.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F18 main body ECU (multiplex network body ECU).


c.
C287239C03
1.417,0.458 1.844,0.719 0.427,0.26 1.5,2.677 1.927,2.938 0.427,0.26 1.021,1.063 1.281,1.063 1.281,1.063 1.531,1.885 true 2.76,4.49 2.5,4.49 2.5,4.49 2.354,4.094 true 1.635,3.563 1.448,3.031 1.448,3.031 1.219,3.031 true 1.635,1.896 1.771,1.042 1.771,1.042 1.885,1.042 true 0.229,2.719 0.542,2.917 0.313,0.198 10 false *1 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.5,0.479 1.813,0.677 0.313,0.198 10 false F18 1.604,2.708 1.917,2.906 0.313,0.198 10 false F25 0.969,2.938 1.479,3.115 0.51,0.177 10 false CG 1.948,0.938 2.458,1.115 0.51,0.177 10 false CANN 0.594,0.958 1.104,1.135 0.51,0.177 10 false CANP 2.823,4.385 3.333,4.563 0.51,0.177 10 false BAT
*1 DLC3
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F18-9 (CANP) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F18-10 (CANN) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F18-9 (CANP) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F18-10 (CANN) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

15.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F111 No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C295270C02
1.635,0.198 2.031,0.5 0.396,0.302 4.979,0.198 5.375,0.5 0.396,0.302 1.208,1.677 0.969,1.281 0.969,1.281 0.833,1.281 true 1.458,1.667 1.063,0.979 1.063,0.979 0.927,0.979 true 1.729,1.677 2.385,0.688 2.385,0.688 2.49,0.688 true 1.229,1.896 1.052,2.177 1.052,2.177 0.938,2.177 true 1.479,1.885 1.333,2.479 1.333,2.479 1.219,2.479 true 1.74,1.896 2.219,2.49 2.219,2.49 2.333,2.49 true 5.146,1.208 5.469,0.771 5.469,0.771 5.604,0.771 true 5.875,1.729 5.604,2.271 5.604,2.271 5.438,2.271 true 1.594,1.656 1.229,0.729 1.229,0.729 1.083,0.729 true 1.604,1.896 1.531,2.667 1.531,2.667 1.406,2.667 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 3.844,0.177 4.156,0.375 0.313,0.198 10 false *1 1.688,0.25 2.094,0.5 0.406,0.25 10 false F111 0.26,1.188 1.177,1.385 0.917,0.198 10 false CANH*b 0.365,0.875 1.281,1.073 0.917,0.198 10 false CANH*c 2.563,0.583 3.479,0.781 0.917,0.198 10 false CANH*e 0.698,2.385 1.615,2.583 0.917,0.198 10 false CANL*c 0.396,2.073 1.313,2.271 0.917,0.198 10 false CANL*b 2.406,2.385 3.323,2.583 0.917,0.198 10 false CANL*e 5.063,0.25 5.427,0.448 0.365,0.198 10 false F25 5.688,0.677 6,0.875 0.313,0.198 10 false CG 5.115,2.167 5.573,2.365 0.458,0.198 10 false BAT 0.521,0.625 1.438,0.823 0.917,0.198 10 false CANH*d 0.875,2.563 1.792,2.76 0.917,0.198 10 false CANL*d
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
*c to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
*d to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
*e to No. 6 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
F111-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Multiplex network door ECU*1
F111-12 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Position control ECU and switch assembly*2
F111-14 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-4 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Outer mirror control ECU assembly (for driver side)*2
F111-15 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-5 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short No. 6 CAN junction connector
F111-16 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Power back door motor unit*1
F111-12 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F111-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Position control ECU and switch assembly*2
F111-14 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F111-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Outer mirror control ECU assembly (for driver side)*2
F111-15 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F111-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short No. 6 CAN junction connector
F111-16 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result Proceed to
OK A
NG (No. 5 CAN junction connector main line) B
NG (ECU or sensor branch line) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

16.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
16.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C287224C07
1.396,0.156 1.75,0.406 0.354,0.25 1.594,2.26 1.948,2.51 0.354,0.25 1.906,1.146 2.052,0.552 2.052,0.552 2.146,0.552 true 1.813,1.156 1.594,0.594 1.594,0.594 1.479,0.594 true 1.646,3.083 1.448,2.625 1.448,2.625 1.323,2.625 true 2.563,4.094 2.469,4.094 2.469,4.094 2.344,3.635 true 0.167,2.49 0.479,2.688 0.313,0.198 10 false *1 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.656,2.292 2.052,2.5 0.396,0.208 10 false F25 1.458,0.188 1.813,0.385 0.354,0.198 10 false F18 2.188,0.448 2.656,0.646 0.469,0.198 10 false CANP 1.073,2.531 1.542,2.729 0.469,0.198 10 false CG 2.615,3.99 3.083,4.188 0.469,0.198 10 false BAT 1.052,0.49 1.667,0.688 0.615,0.198 10 false CANN
*1 DLC3
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F18-9 (CANP) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F18-10 (CANN) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F18-9 (CANP) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F18-10 (CANN) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU SENSOR BUS LINES OR CONNECTOR

17.CHECK SUB BUS 1
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C287224C08
1.542,2.469 1.969,2.76 0.427,0.292 1.5,0.292 1.906,0.573 0.406,0.281 1.25,1.948 1.375,1.948 1.375,1.948 1.813,1.188 true 2.375,1.938 2.26,1.938 2.26,1.938 1.906,1.188 true 1.635,3.104 0.958,2.708 0.958,2.708 0.75,2.708 true 1.865,4.063 2.031,4.063 2.031,4.063 2.344,3.635 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.073,2.427 0.385,2.625 0.313,0.198 10 false *1 1.646,2.521 1.958,2.719 0.313,0.198 10 false F25 1.583,0.333 1.896,0.531 0.313,0.198 10 false F18 0.813,1.854 1.427,2.052 0.615,0.198 10 false CANN 2.438,1.844 3.052,2.042 0.615,0.198 10 false CANP 0.51,2.615 0.823,2.813 0.313,0.198 10 false CG 1.563,3.969 2.021,4.167 0.458,0.198 10 false BAT
*1 DLC3
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus line
F18-9 (CANP) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F18-10 (CANN) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F18-9 (CANP) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F18-10 (CANN) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

18.CHECK FOR DTC OUTPUT

B

19.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

23.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

28.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 6 CAN JUNCTION CONNECTOR)
18.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON.


h.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC U1002 not output from main body ECU (multiplex network body ECU) (GTS display: Main Body) A
DTC U1002 is output from main body ECU (multiplex network body ECU) (GTS display: Main Body) B



A

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

19.CHECK FOR OPEN IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.
C285508C14
1.396,0.167 1.813,0.417 0.417,0.25 1.469,1.302 1.094,0.542 1.094,0.542 0.844,0.542 true 1.563,1.302 1.771,0.542 1.771,0.542 2.021,0.542 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.438,0.438 1.052,0.635 0.615,0.198 10 false CANP 2.073,0.438 2.688,0.635 0.615,0.198 10 false CANN 1.49,0.198 2.104,0.396 0.615,0.198 10 false F18
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

20.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
20.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
a.

Reconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.
C292400C02
1.5,0.281 1.938,0.563 0.438,0.281 0.573,1.854 0.646,1.854 0.646,1.854 0.76,1.427 true 1.083,1.854 1.01,1.854 1.01,1.854 0.885,1.438 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 1.646,0.323 2.104,0.521 0.458,0.198 10 false X6 0.156,1.75 0.771,1.948 0.615,0.198 10 false CANP 1.146,1.75 1.76,1.948 0.615,0.198 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

21.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
21.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the X6 multiplex network door ECU connector.


b.

Disconnect the F112 No. 6 CAN junction connector.


c.
C292406C05
1.5,0.313 1.958,0.635 0.458,0.323 1.104,1.99 1.01,0.885 1.01,0.885 0.823,0.885 true 1.115,2.26 0.99,2.729 0.99,2.729 0.865,2.729 true 1.573,1.958 2.177,0.875 2.177,0.875 2.333,0.875 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.25,0.781 1.167,0.979 0.917,0.198 10 false CANH*b 0.281,2.635 1.198,2.833 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*c 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*c 1.583,0.375 1.99,0.594 0.406,0.219 10 false F112
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to No. 5 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F112-2 (CANH) - F112-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
F112-5 (CANH) - F112-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector



Result:
Result Proceed to
OK A
NG (Main body ECU (multiplex network body ECU) main line) B
NG (No. 5 CAN junction connector main line) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

22.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
22.CHECK FOR OPEN IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F111 No. 5 CAN junction connector.


c.
C292406C09
1.5,0.313 1.958,0.635 0.458,0.323 0.948,1.969 0.844,0.844 0.844,0.844 0.75,0.844 true 0.958,2.26 0.906,2.708 0.906,2.708 0.802,2.708 true 1.573,1.948 2.177,0.865 2.177,0.865 2.333,0.865 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.188,0.76 1.104,0.958 0.917,0.198 10 false CANH*b 0.26,2.615 1.177,2.813 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*c 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*c 1.583,0.365 1.979,0.583 0.396,0.219 10 false F111
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
*c to No. 6 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F111-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Multiplex network door ECU
F111-5 (CANH) - F111-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector main line) B
NG (Multiplex network door ECU main line) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

23.CHECK FOR SHORT IN SUB BUS 1 LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.
C285508C15
1.396,0.167 1.813,0.417 0.417,0.25 1.469,1.302 1.094,0.542 1.094,0.542 0.844,0.542 true 1.563,1.302 1.771,0.542 1.771,0.542 2.021,0.542 true 0.104,0.052 0.417,0.208 0.313,0.156 10 false *a 0.427,0.448 1.042,0.646 0.615,0.198 10 false CANP 2.073,0.448 2.688,0.646 0.615,0.198 10 false CANN 1.49,0.188 2.104,0.385 0.615,0.198 10 false F18
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

24.CHECK FOR SHORT IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
24.CHECK FOR SHORT IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU)
a.

Reconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the X6 multiplex network door ECU connector.


c.
C292400C03
1.5,0.281 1.938,0.563 0.438,0.281 0.573,1.854 0.646,1.854 0.646,1.854 0.76,1.427 true 1.083,1.854 1.01,1.854 1.01,1.854 0.885,1.438 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 1.635,0.323 2.094,0.521 0.458,0.198 10 false X6 0.156,1.75 0.771,1.948 0.615,0.198 10 false CANP 1.146,1.75 1.76,1.948 0.615,0.198 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

25.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
25.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the X6 multiplex network door ECU connector.


b.

Disconnect the F112 No. 6 CAN junction connector.


c.
C292406C07
1.5,0.313 1.958,0.635 0.458,0.323 1.104,1.99 1.01,0.885 1.01,0.885 0.823,0.885 true 1.115,2.26 0.99,2.729 0.99,2.729 0.865,2.729 true 1.573,1.958 2.521,0.875 2.521,0.875 2.635,0.875 true 1.583,2.26 2.583,2.698 2.583,2.698 2.667,2.698 true 1.25,1.958 1.135,0.635 1.135,0.635 1.021,0.635 true 1.271,2.26 1.177,3.063 1.177,3.063 1.063,3.063 true 1.417,1.979 2.313,0.677 2.313,0.677 2.427,0.677 true 1.406,2.24 2.25,3.042 2.25,3.042 2.396,3.042 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.25,0.781 1.167,0.979 0.917,0.198 10 false CANH*b 0.281,2.635 1.198,2.833 0.917,0.198 10 false CANL*b 2.708,0.781 3.313,0.979 0.604,0.198 10 false CANH*e 2.74,2.604 3.385,2.802 0.646,0.198 10 false CANL*e 1.573,0.375 2,0.573 0.427,0.198 10 false F112 0.448,0.542 1.365,0.74 0.917,0.198 10 false CANH*c 0.521,2.969 1.438,3.167 0.917,0.198 10 false CANL*c 2.51,0.594 3.115,0.792 0.604,0.198 10 false CANH*d 2.469,2.938 3.115,3.135 0.646,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
*d to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
*e to No. 5 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F112-2 (CANH) - F112-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
F112-3 (CANH) - F112-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly (for driver side)*
F112-4 (CANH) - F112-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Position control ECU and switch assembly*
F112-5 (CANH) - F112-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector


*: w/ Seat Position Memory System


Result:
Result Proceed to
OK A
NG (Main body ECU (multiplex network body ECU) main line) B
NG (ECU or sensor branch line) C
NG (No. 5 CAN junction connector main line) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

27.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)

D

26.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
26.CHECK FOR SHORT IN SUB BUS 1 LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F111 No. 5 CAN junction connector.


c.
C292406C08
1.5,0.313 1.958,0.635 0.458,0.323 0.948,1.99 0.844,0.865 0.844,0.865 0.75,0.865 true 0.958,2.26 0.906,2.708 0.906,2.708 0.802,2.708 true 1.573,1.958 2.177,0.875 2.177,0.875 2.333,0.875 true 1.583,2.26 1.76,2.719 1.76,2.719 1.854,2.719 true 1.427,1.969 1.135,0.365 1.135,0.365 1,0.365 true 1.417,2.25 1.208,3.135 1.208,3.135 1.104,3.135 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.188,0.76 1.104,0.958 0.917,0.198 10 false CANH*b 0.26,2.615 1.177,2.813 0.917,0.198 10 false CANL*b 2.406,0.781 3.323,0.979 0.917,0.198 10 false CANH*d 1.917,2.615 2.833,2.813 0.917,0.198 10 false CANL*d 1.583,0.365 1.979,0.583 0.396,0.219 10 false F111 0.448,0.26 1.365,0.458 0.917,0.198 10 false CANH*c 0.583,3.042 1.5,3.24 0.917,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
*d to No. 6 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F111-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Multiplex network door ECU*1
F111-4 (CANH) - F111-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly (for front passenger side)*2
F111-5 (CANH) - F111-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector


·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (Multiplex network door ECU main line) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

27.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - MULTIPLEX NETWORK DOOR ECU)

27.CHECK FOR SHORT IN SUB BUS 1 LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C295269C01
1.521,0.125 1.927,0.438 0.406,0.313 0.927,1.74 1.094,1.74 1.094,1.74 1.802,0.885 true 2.49,1.74 2.385,1.74 2.385,1.74 1.896,0.885 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.604,0.188 1.938,0.406 0.333,0.219 10 false F18 0.49,1.625 1.104,1.823 0.615,0.198 10 false CANN 2.573,1.646 3.188,1.844 0.615,0.198 10 false CANP
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU SENSOR BUS LINES OR CONNECTOR

28.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the F112 No. 6 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C295270C03
1.635,0.198 2.031,0.5 0.396,0.302 4.979,0.198 5.375,0.5 0.396,0.302 1.354,1.667 0.969,1.281 0.969,1.281 0.833,1.281 true 1.458,1.667 1.063,0.979 1.063,0.979 0.927,0.979 true 1.729,1.677 2.385,0.688 2.385,0.688 2.49,0.688 true 1.354,1.896 1.052,2.177 1.052,2.177 0.938,2.177 true 1.479,1.885 1.333,2.479 1.333,2.479 1.219,2.479 true 1.74,1.896 2.219,2.49 2.219,2.49 2.333,2.49 true 5.146,1.208 5.469,0.771 5.469,0.771 5.604,0.771 true 5.875,1.729 5.604,2.271 5.604,2.271 5.438,2.271 true 1.594,1.667 1.25,0.677 1.25,0.677 1.125,0.677 true 1.604,1.875 1.479,2.708 1.479,2.708 1.365,2.708 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 3.844,0.177 4.156,0.375 0.313,0.198 10 false *1 1.688,0.24 2.104,0.469 0.417,0.229 10 false F112 0.26,1.188 1.177,1.385 0.917,0.198 10 false CANH*b 0.365,0.875 1.281,1.073 0.917,0.198 10 false CANH*c 2.563,0.583 3.479,0.781 0.917,0.198 10 false CANH*e 0.698,2.385 1.615,2.583 0.917,0.198 10 false CANL*c 0.396,2.073 1.313,2.271 0.917,0.198 10 false CANL*b 2.406,2.396 3.323,2.594 0.917,0.198 10 false CANL*e 5.063,0.25 5.375,0.448 0.313,0.198 10 false F25 5.688,0.677 6,0.875 0.313,0.198 10 false CG 5.115,2.167 5.573,2.365 0.458,0.198 10 false BAT 0.552,0.583 1.469,0.781 0.917,0.198 10 false CANH*d 0.844,2.604 1.75,2.771 0.906,0.167 10 false CANL*d
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
*d to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
*e to No. 5 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
F112-2 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Main body ECU (multiplex network body ECU)
F112-13 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Outer mirror control ECU assembly (for driver side)*
F112-14 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-4 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Position control ECU and switch assembly*
F112-15 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-5 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short No. 5 CAN junction connector
F112-16 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F112-2 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Main body ECU (multiplex network body ECU)
F112-13 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F112-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Outer mirror control ECU assembly (for driver side)*
F112-14 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F112-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Position control ECU and switch assembly*
F112-15 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F112-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short No. 5 CAN junction connector
F112-16 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Seat Position Memory System

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result Proceed to
OK A
NG (Main body ECU (multiplex network body ECU) main line) B
NG (ECU or sensor bus line) C
NG (No. 5 CAN junction connector main line) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

29.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

31.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)

D

30.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 5 CAN JUNCTION CONNECTOR)
29.CHECK FOR SHORT IN SUB BUS 1 LINE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F18 main body ECU (multiplex network body ECU).


c.
C287239C05
1.417,0.458 1.844,0.719 0.427,0.26 1.5,2.677 1.927,2.938 0.427,0.26 1.021,1.063 1.281,1.063 1.281,1.063 1.531,1.885 true 2.76,4.49 2.5,4.49 2.5,4.49 2.354,4.094 true 1.635,3.563 1.448,3.031 1.448,3.031 1.219,3.031 true 1.635,1.896 1.771,1.042 1.771,1.042 1.885,1.042 true 0.229,2.719 0.542,2.917 0.313,0.198 10 false *1 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.5,0.479 1.813,0.677 0.313,0.198 10 false F18 1.604,2.708 1.917,2.906 0.313,0.198 10 false F25 0.969,2.938 1.479,3.115 0.51,0.177 10 false CG 1.948,0.938 2.458,1.115 0.51,0.177 10 false CANN 0.594,0.958 1.104,1.135 0.51,0.177 10 false CANP 2.823,4.385 3.333,4.563 0.51,0.177 10 false BAT
*1 DLC3
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F18-9 (CANP) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F18-10 (CANN) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F18-9 (CANP) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F18-10 (CANN) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

30.CHECK FOR SHORT IN SUB BUS 1 LINE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the F112 No. 6 CAN junction connector.


b.

Disconnect the F111 No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C295270C04
1.635,0.198 2.031,0.5 0.396,0.302 4.979,0.198 5.375,0.5 0.396,0.302 1.208,1.677 0.969,1.281 0.969,1.281 0.833,1.281 true 1.729,1.677 2.385,0.688 2.385,0.688 2.49,0.688 true 1.229,1.896 1.052,2.177 1.052,2.177 0.938,2.177 true 1.74,1.896 2.219,2.49 2.219,2.49 2.333,2.49 true 5.146,1.208 5.469,0.771 5.469,0.771 5.604,0.771 true 5.875,1.729 5.604,2.271 5.604,2.271 5.438,2.271 true 1.594,1.656 1.229,0.729 1.229,0.729 1.083,0.729 true 1.604,1.896 1.531,2.667 1.531,2.667 1.406,2.667 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 3.844,0.177 4.156,0.375 0.313,0.198 10 false *1 1.677,0.24 2.073,0.458 0.396,0.219 10 false F111 0.26,1.188 1.177,1.385 0.917,0.198 10 false CANH*b 2.563,0.583 3.479,0.781 0.917,0.198 10 false CANH*d 0.396,2.073 1.313,2.271 0.917,0.198 10 false CANL*b 2.406,2.385 3.323,2.583 0.917,0.198 10 false CANL*d 5.052,0.25 5.365,0.448 0.313,0.198 10 false F25 5.688,0.677 6,0.875 0.313,0.198 10 false CG 5.115,2.167 5.573,2.365 0.458,0.198 10 false BAT 0.521,0.625 1.438,0.823 0.917,0.198 10 false CANH*c 0.875,2.563 1.792,2.76 0.917,0.198 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
*d to No. 6 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
F111-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Multiplex network door ECU*1
F111-12 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-4 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Outer mirror control ECU assembly (for front passenger side)*2
F111-15 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-5 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short No. 6 CAN junction connector
F111-16 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F111-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Multiplex network door ECU*1
F111-12 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F111-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Outer mirror control ECU assembly (for front passenger side)*2
F111-15 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
F111-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short No. 6 CAN junction connector
F111-16 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result Proceed to
OK A
NG (No. 5 CAN junction connector main line) B
NG (ECU or sensor branch line) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

31.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
31.CHECK FOR SHORT IN SUB BUS 1 LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C287224C09
1.396,0.156 1.75,0.406 0.354,0.25 1.594,2.26 1.948,2.51 0.354,0.25 1.906,1.146 2.052,0.552 2.052,0.552 2.146,0.552 true 1.813,1.156 1.594,0.594 1.594,0.594 1.479,0.594 true 1.646,3.083 1.448,2.625 1.448,2.625 1.323,2.625 true 2.563,4.094 2.469,4.094 2.469,4.094 2.344,3.635 true 0.167,2.49 0.479,2.688 0.313,0.198 10 false *1 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.656,2.292 2.031,2.531 0.375,0.24 10 false F25 1.448,0.188 1.802,0.406 0.354,0.219 10 false F18 2.188,0.448 2.656,0.646 0.469,0.198 10 false CANP 1.073,2.531 1.542,2.729 0.469,0.198 10 false CG 2.615,3.99 3.083,4.188 0.469,0.198 10 false BAT 1.052,0.49 1.667,0.688 0.615,0.198 10 false CANN
*1 DLC3
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F18-9 (CANP) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F18-10 (CANN) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F18-9 (CANP) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F18-10 (CANN) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 1 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 1 inspection.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU SENSOR BUS LINES OR CONNECTOR