Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2) › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0303251 CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2) A

2GR-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2)  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL RH

Hide 53736 2.REMOVE FRONT FENDER APRON SEAL RH

Hide 11209 3.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

Hide 55701J 5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 47220D 6.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

Hide 47233 7.REMOVE RESERVOIR BRACKET (for RHD)

Hide 12327A 8.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 12313 9.REMOVE ENGINE MOVING CONTROL ROD BRACKET

Hide 15370 10.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 11.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A368570C01
1.698,1.292 2.188,1.292 true 1.469,1.313 1.198,1.719 1.198,1.719 0.958,1.719 true 2.198,1.198 2.375,1.396 0.177,0.198 10 true *a 0.781,1.646 0.958,1.844 0.177,0.198 10 true *b
*a Timing Mark
*b Timing Mark (Cutout)


Turn the crankshaft pulley clockwise until its timing mark (cutout) is aligned with the timing mark on the timing chain cover assembly as shown in the illustration.


b.

Check that the cutout of the camshaft timing gear assembly is at the top.

A395722C01
2.885,0.781 3.208,0.479 3.208,0.479 3.396,0.479 true 2.219,3.552 2.448,3.552 2.448,3.552 2.719,3.281 true 5.125,3.323 5.125,3.167 5.125,3.167 5.365,3.042 true 5.208,0.896 5.667,0.896 true 0.885,1.104 1.198,1.26 0.313,0.156 10 false *a 0.917,2.906 1.229,3.063 0.313,0.156 10 false *b 5.698,0.792 5.938,1.01 0.24,0.219 10 true *c 1.76,0.823 1.99,1.052 0.229,0.229 10 true *d 5.073,3.323 5.385,3.479 0.313,0.156 10 false *c 1.99,3.479 2.208,3.667 0.219,0.188 10 true *c 3.427,0.375 3.667,0.563 0.24,0.188 10 true *c 1.75,2.656 1.979,2.885 0.229,0.229 10 true *d
*a Correct *b Incorrect
*c Cutout *d Up


HINT:

If the cutout of the camshaft timing gear assembly (for intake side) is not at the top, turn the crankshaft 360° clockwise and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing chain cover assembly again.



Hide 12.REMOVE CAMSHAFT TIMING GEAR BOLT

a.
A394327

While holding the crankshaft pulley, remove the camshaft timing gear bolt.

NOTICE:
·

If the camshaft timing gear bolt has been struck or dropped, replace it.

·

Do not turn the crankshaft pulley after removing the camshaft timing gear bolt.