Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CAMSHAFT › 2016.11–2018.09
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109590 CAMSHAFT A

1AR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11821 1.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 2.INSTALL NO. 1 CAMSHAFT BEARING

Hide 15678A 3.INSTALL OIL CONTROL VALVE FILTER

Hide 13070A 4.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Secure the No. 2 camshaft in a vise by clamping the hexagonal part between aluminum plates.

NOTICE:

Do not damage the No. 2 camshaft by tightening the vise excessively.



b.
A196902C26
1.896,0.656 1.771,0.656 1.771,0.656 1.594,0.927 false 1.229,0.177 1.104,0.177 1.104,0.177 0.667,0.802 false 2,0.573 2.167,0.74 0.167,0.167 10 false *b 1.281,0.115 1.594,0.313 0.313,0.198 10 false *a
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the No. 2 camshaft with the knock pin hole of the camshaft timing exhaust gear assembly.


c.
A196904C72
2.146,0.865 1.896,0.865 1.896,0.865 1.5,1.083 false 0.823,0.76 0.917,0.76 0.917,0.76 1.125,0.979 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing exhaust gear assembly and camshaft flange.


d.
A250991

Secure the camshaft timing exhaust gear assembly with the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Do not disassemble the camshaft timing exhaust gear assembly.


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 5.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A288402C02
3.063,1.438 2.969,1.438 2.969,1.438 1.802,0.74 false 3.083,1.354 3.271,1.521 0.188,0.167 10 false *a
*a Timing Notch (Groove)


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.


Hide 13512 6.INSTALL NO.2 CAMSHAFT

a.
A196911C35
1.073,0.229 1.24,0.229 1.24,0.229 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.729,1.125 1.063,1.125 true 2.906,0.958 3.104,1.281 0.198,0.323 10 false *2 0.865,0.146 1.042,0.323 0.177,0.177 10 false *1 0.552,1.042 0.75,1.375 0.198,0.333 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


b.

Clean the camshaft journals.


c.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


d.
A287579C03
2.219,3.365 2.781,2.948 2.781,2.948 2.927,2.948 false 2.167,3.646 2.75,3.646 false 2.292,4.219 2.708,4.219 false 2.969,2.854 3.229,3.094 0.26,0.24 10 false *a 2.771,3.563 3.031,3.802 0.26,0.24 10 false *b 2.719,4.135 2.906,4.292 0.188,0.156 10 false A
*a Paint Mark
*b Timing Mark


Hold up the chain sub-assembly, align the timing mark and paint mark, and install the No. 2 camshaft.

HINT:
·

"A" is not a timing mark.

·

Perform "Inspection After Repair" after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13511 7.INSTALL CAMSHAFT

a.
A196911C36
1.073,0.229 1.24,0.229 1.24,0.229 1.563,0.542 false 2.854,1.042 2.531,1.042 false 0.729,1.125 1.063,1.125 true 2.906,0.958 3.104,1.281 0.198,0.323 10 false *2 0.865,0.146 1.042,0.323 0.177,0.177 10 false *1 0.552,1.042 0.75,1.375 0.198,0.333 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


b.

Clean the camshaft journals.


c.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


d.
A251007C08
1.042,2.677 0.688,2.573 false 1.167,2.167 1.354,2.333 0.188,0.167 10 false *b 0.5,2.479 0.688,2.646 0.188,0.167 10 false *a
*a Knock Pin
*b Approximately 17°


Install the camshaft to the camshaft housing sub-assembly as shown in the illustration.

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 8.INSTALL CAMSHAFT BEARING CAP

a.
A250994

Confirm the marks and numbers on the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps and place them in their proper positions and directions.


b.
A250988N04
1.802,1.813 1.917,1.979 0.115,0.167 10 true 2 2.365,0.406 2.479,0.573 0.115,0.167 10 true 3 2.396,1.813 2.51,1.979 0.115,0.167 10 false 4 1.208,0.406 1.323,0.573 0.115,0.167 10 true 5 1.198,1.813 1.313,1.979 0.115,0.167 10 true 6 2.958,0.406 3.073,0.573 0.115,0.167 10 true 7 3,1.813 3.115,1.979 0.115,0.167 10 false 8 0.656,0.354 0.771,0.521 0.115,0.167 10 true 9 0.521,1.99 0.708,2.156 0.188,0.167 10 false 10 1.802,0.406 1.917,0.573 0.115,0.167 10 true 1

Uniformly tighten the 10 bolts in several steps in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


c.
A250989N04
1.792,1.573 1.906,1.74 0.115,0.167 10 true 1 1.781,0.073 1.896,0.24 0.115,0.167 10 true 2 2.406,1.573 2.521,1.74 0.115,0.167 10 true 3 2.333,0.073 2.448,0.24 0.115,0.167 10 false 4 1.188,1.573 1.302,1.74 0.115,0.167 10 true 5 1.229,0.073 1.344,0.24 0.115,0.167 10 false 6 3,1.573 3.115,1.74 0.115,0.167 10 true 7 2.906,0.073 3.021,0.24 0.115,0.167 10 false 8 0.24,1.063 0.354,1.229 0.115,0.167 10 true 9 0.615,0.042 0.802,0.208 0.188,0.167 10 false 10 0.542,1.865 0.729,2.031 0.188,0.167 10 true 11

Uniformly tighten the 11 bolts in several steps in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


d.

Check the torque of each bolt again.


Hide 13050 9.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A284096C25
0.865,1.729 1.021,1.729 1.021,1.729 1.781,1.333 false 0.771,3.969 0.927,3.969 0.927,3.969 1.688,3.573 false 2.042,1.604 2.458,1.948 2.458,1.948 2.615,1.948 false 2.073,3.677 2.438,3.417 2.438,3.417 2.583,3.417 false 0.083,0.25 0.396,0.406 0.313,0.156 10 false *a 0.083,2.583 0.396,2.74 0.313,0.156 10 false *b 0.708,1.625 1.021,1.781 0.313,0.156 10 false *d 2.667,1.844 2.979,2 0.313,0.156 10 false *c 2.635,3.323 2.948,3.479 0.313,0.156 10 false *c 0.604,3.854 0.917,4.01 0.313,0.156 10 false *d
*a Advanced Position
*b Retarded Position
*c Alignment Mark
*d Knock Pin Hole


Check the camshaft timing gear assembly position.

NOTICE:
·

If the camshaft timing gear assembly is set to the advanced position, do not let the camshaft timing gear assembly rotate clockwise during installation.

·

If the camshaft timing gear assembly has rotated to the most retarded position, make sure to release the lock pin and set the camshaft timing gear assembly to the most advanced position before tightening the bolt of the camshaft timing gear assembly.




b.
A251004C09
2.043,2.092 2.214,2.252 0.171,0.16 10 *a 2.109,3.019 2.28,3.178 0.171,0.16 10 *b
*a Narrow
*b Wide


Install the camshaft timing gear assembly as shown in the illustration.


c.
A250998C09
1.167,2.021 1.354,2.188 0.188,0.167 10 false *a 2.677,2.979 2.865,3.146 0.188,0.167 10 false *a 1.219,2.948 1.406,3.115 0.188,0.167 10 false *b 2.74,2.031 2.927,2.198 0.188,0.167 10 false *b
*a Narrow
*b Wide


Turn the camshaft timing gear assembly approximately 180° counterclockwise.


d.
A250999C12
1.375,0.74 0.563,0.313 true 1.354,1 0.271,1 true 1.844,1.417 1.917,1.865 1.917,1.865 2.063,1.865 true 0.365,0.188 0.604,0.354 0.24,0.167 10 false *a 0.104,0.896 0.375,1.063 0.271,0.167 10 false *b 2.135,1.76 2.292,1.958 0.156,0.198 10 true A
*a Paint Mark
*b Timing Mark


Align the paint mark with the timing mark and install the chain sub-assembly to the camshaft timing gear assembly.

HINT:

"A" is not a timing mark.



e.
A196901C54
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 false 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 false 1.292,0.115 1.5,0.323 0.208,0.208 10 false *a 2.021,0.542 2.281,0.729 0.26,0.188 10 false *b
*a Knock Pin
*b Knock Pin Hole


Align and fit the knock pin of the camshaft with the knock pin hole of the camshaft timing gear assembly.


f.
A196904C73
2.146,0.865 1.896,0.865 1.896,0.865 1.5,1.083 false 0.823,0.771 0.917,0.771 0.917,0.771 1.125,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 1.802,0.531 2,0.698 0.198,0.167 10 false *c 2.188,0.75 2.365,0.917 0.177,0.167 10 false *2 1.74,2.021 1.938,2.177 0.198,0.156 10 false *d 0.063,0.042 0.25,0.208 0.188,0.167 10 false *a 0.063,1.833 0.26,2 0.198,0.167 10 false *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing gear assembly and camshaft flange.


g.

Secure the camshaft in place by hand, and then install the bolt of the camshaft timing gear assembly by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



h.

If the lock pin has not been released, release it.

i.
A249942C08
1.063,0.979 0.458,0.635 false 0.375,0.969 1.115,1.125 false 0.26,0.521 0.438,0.688 0.177,0.167 10 false *b 0.208,0.854 0.385,1.021 0.177,0.167 10 false *a
*a Make a Hole
*b Adhesive Tape Sealing Area


After cleaning the intake side VVT oil hole on the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Make a hole in the adhesive tape covering the oil hole as shown in the illustration. (Procedure A)


iii.
A251001

Apply approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the hole made in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach the adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




iv.

Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

HINT:
·

Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




v.

Remove the adhesive tape from the No. 1 camshaft bearing cap.



i.
A249935C01
2.135,0.135 2.448,0.333 0.313,0.198 10 true *a 0.875,0.354 1.188,0.552 0.313,0.198 10 true *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.



j.
A287580C03
0.979,0.917 1.865,0.333 1.865,0.333 3.01,0.969 true 0.979,1.135 1.896,1.927 1.896,1.927 2.969,1.167 true 1.865,1.625 1.865,1.521 1.865,1.521 1.563,1.281 true 3.188,1.76 3.188,1.656 3.188,1.656 3.083,1.573 false 1.76,0.115 1.938,0.313 0.177,0.198 10 true *a 1.813,1.948 2.063,2.156 0.25,0.208 10 false *b 1.813,1.625 1.99,1.792 0.177,0.167 10 false A 3.156,1.802 3.406,2.094 0.25,0.292 10 false A
*a Paint Mark
*b Timing Mark


Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration.

HINT:
·

"A" is not a timing mark.

·

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13540 12.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A288403N02
1.813,0.156 2.094,0.323 0.281,0.167 10 true 10°

Turn the crankshaft pulley approximately 10° clockwise.


b.

Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure not to drop the gasket inside the timing chain cover sub-assembly.



c.

Remove the pin from the stopper plate.


Hide 13.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.

A287581C02
2.867,0.403 3.105,0.648 0.239,0.244 10 *d 2.16,3.551 2.398,3.718 0.239,0.167 10 *a 1.587,2.379 2.253,3.528 2.253,3.528 3.066,2.411 false 2.207,3.144 2.341,3.323 0.134,0.179 10 A 2.25,3.144 2.25,2.92 2.25,2.92 2.015,2.489 false 3.163,3.283 3.297,3.461 0.134,0.179 10 A 3.211,2.86 3.211,3.279 false 5.97,1.177 6.209,1.344 0.239,0.167 10 *b 5.34,1.703 5.835,1.251 5.835,1.251 5.943,1.251 false 1.637,0.39 1.876,0.557 0.239,0.167 10 *c
*a Timing Mark *b Timing Notch
*c Approximately 7° *d Approximately 32°



b.

Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 11324 14.INSTALL TIMING CHAIN COVER PLATE

a.

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15.INSTALL TIMING CHAIN COVER TIGHT PLUG

Hide 11201 16.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 82121 18.CONNECT ENGINE WIRE

a.

Install the engine wire to the engine assembly with the 3 bolts and 4 nuts.

A283839N01
1.677,3.969 1.958,4.198 0.281,0.229 10 false A 2.021,1.99 2.302,2.219 0.281,0.229 10 false B 4.969,2.458 5.25,2.688 0.281,0.229 10 false B 3.115,2.469 3.396,2.698 0.281,0.229 10 true B

Torque:
Nut (A) : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut (B) : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
Bolt : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.

Connect the 12 connectors and 5 clamps.


c.

Engage the 2 claws to connect the inlet heater water hose and outlet heater water hose A.


Hide 12363A 19.INSTALL ENGINE MOVING CONTROL ROD

Hide 12327A 20.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 17701 21.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 22.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 23.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17750A 24.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 25.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 26.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53298E 27.INSTALL RADIATOR SIDE SEAL RH

Hide 53299D 28.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH

Hide 29.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 53736 31.INSTALL FRONT FENDER APRON SEAL RH

Hide 53875A 32.INSTALL FRONT FENDER LINER RH

Hide 51441 33.INSTALL NO. 1 ENGINE UNDER COVER

Hide 34.INSTALL FRONT WHEEL RH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)