1.INSTALL STUD BOLT
If a stud bolt is deformed or the threads are damaged, replace it.
Using an E8 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.
17177
2.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
Install 2 new No. 1 intake manifold to head gaskets to each cylinder head sub-assembly.
Align the port holes of the No. 1 intake manifold to head gaskets and cylinder head sub-assembly.
Make sure that the No. 1 intake manifold to head gaskets are installed in the correct direction.
17111
3.INSTALL INTAKE MANIFOLD
Temporarily install the intake manifold to the cylinder head sub-assembly with the 4 bolts and 4 nuts.
Tighten the 4 bolts and 4 nuts in the order shown in the illustration.
23291
4.INSTALL INJECTOR VIBRATION INSULATOR
23807V
5.INSTALL NO. 1 DELIVERY PIPE SPACER
23800
6.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY
7.CONNECT FUEL TUBE SUB-ASSEMBLY
12327
8.INSTALL REAR ENGINE MOUNTING STAY RH
Install the rear engine mounting stay RH to the intake manifold with the bolt.
Connect the engine wire to the rear engine mounting stay RH with the bolt.
12327A
9.INSTALL NO. 2 ENGINE MOUNTING STAY RH
Install the No. 2 engine mounting stay RH to the engine mounting insulator sub-assembly RH and rear engine mounting stay RH with the bolt and 2 nuts.
11254
10.INSTALL NO. 1 V-BANK COVER BRACKET
Perform this procedure only when replacement of the No. 1 V-bank cover bracket is necessary.
Install the 2 No. 1 V-bank cover brackets to the intake air surge tank assembly.
17176
11.INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET
Install a new air surge tank to intake manifold gasket to the intake air surge tank assembly.
17190
12.INSTALL INTAKE AIR SURGE TANK ASSEMBLY
Do not apply oil to the bolts and nuts as listed below:
| Oil Application Prohibited Bolt and Nut |
|---|
| Bolt and Nut for Intake Air Surge Tank Assembly and Intake Manifold |
Temporarily install the intake air surge tank assembly to the intake manifold with the 5 bolts and 2 nuts.
Temporarily install the No. 2 surge tank stay to the intake air surge tank assembly and camshaft housing RH with the 2 bolts.
Tighten the 5 bolts and 2 nuts in the order shown in the illustration.
Tighten the 2 bolts in the order shown in the illustration.
| *1 | Vacuum Hose Sub-assembly |
| *2 | Vacuum Hose |
| *3 | No. 2 Air Tube |
Engage the clamp to connect the No. 2 air tube to the intake air surge tank assembly.
Engage the clamp to connect the vacuum hose to the intake air surge tank assembly.
Engage the 2 clamps to connect the vacuum hose sub-assembly to the intake air surge tank assembly.
Engage the 2 clamps to connect the vacuum hose sub-assembly to the intake air surge tank assembly.
Connect the No. 1 vacuum switching valve assembly (for ACIS) connector.
25860
13.CONNECT PURGE VALVE (PURGE VSV)
Connect the purge valve (purge VSV) to the intake air surge tank assembly with the bolt.
Connect the No. 1 fuel vapor feed hose to the intake air surge tank assembly.
12261
14.CONNECT VENTILATION HOSE
Connect the ventilation hose to the intake air surge tank assembly and slide the clip to secure it.
22030
15.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
55704B
16.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY
17.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH
53607B
18.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
53892C
19.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH
53891C
20.INSTALL FRONT FENDER SPLASH SHEILD SEAL FRONT RH
Perform the same procedure as for the LH side.
53808A
21.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH
53807A
22.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH
Perform the same procedure as for the LH side.
23.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
25.INSPECT FOR FUEL LEAK
11209
26.INSTALL V-BANK COVER SUB-ASSEMBLY