Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Rear Television Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Television Camera Communication Stop Mode Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Rear television camera assembly branch line or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly

·

Radio and display receiver assembly (w/ Parking Assist Monitor System)

·

Parking assist ECU (w/ Panoramic View Monitor System)



WIRING DIAGRAM

C424510E01
0.146,1.99 0.604,2.188 0.458,0.198 10 false M97 0.479,1.99 3.354,2.365 2.875,0.375 10 false No. 10 Global CAN Junction Connector 1.74,0.896 2.198,1.094 0.458,0.198 10 false 5 1.708,1.469 2.167,1.667 0.458,0.198 10 false 11 5.427,0.917 5.885,1.115 0.458,0.198 10 false 4 5.417,1.469 5.875,1.667 0.458,0.198 10 false 1 5.417,2.469 5.875,2.667 0.458,0.198 10 false 6 5.417,3.5 5.875,3.698 0.458,0.198 10 false 5 5.656,1.042 6.156,1.302 0.5,0.26 10 false CANH 5.646,1.573 6.146,1.833 0.5,0.26 10 false CANL 5.656,2.594 6.156,2.854 0.5,0.26 10 false CB+ 5.635,3.583 6.135,3.844 0.5,0.26 10 false CGND 0.344,2.583 3.229,3.073 2.885,0.49 10 false from Radio and Display Receiver Assembly*1 0.438,3.604 3.99,4.167 3.552,0.563 10 false to Radio and Display Receiver Assembly*1 4.99,4.75 5.49,5.01 0.5,0.26 10 false W15 5.365,4.75 6.823,5.344 1.458,0.594 10 false Rear Television Camera Assembly 1.427,3.083 4.313,3.573 2.885,0.49 10 false from Parking Assist ECU*2 1.51,4.073 5.063,4.635 3.552,0.563 10 false to Parking Assist ECU*2 0.115,4.885 3.479,5.146 3.365,0.26 10 false *1: w/ Parking Assist Monitor System 0.125,5.271 4.021,5.5 3.896,0.229 10 false *2: w/ Panoramic View Monitor System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the W15 rear television camera assembly connector.


c.
C427510C03
0.25,1.01 0.667,1.313 0.417,0.302 1.385,0.177 1.552,0.177 1.552,0.177 1.552,1.01 true 1.396,1.958 1.563,1.958 1.563,1.958 1.563,1.375 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 0.969,1.885 1.458,2.104 0.49,0.219 10 false CANH 0.969,0.115 1.458,0.333 0.49,0.219 10 false CANL 0.313,1.073 0.802,1.292 0.49,0.219 10 false W15
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W15-4 (CANH) - W15-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)

2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Parking Assist Monitor System A
w/ Panoramic View Monitor System B



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427510C04
0.25,1.01 0.667,1.313 0.417,0.302 1.552,1.948 1.719,1.948 1.719,1.948 1.719,1.365 true 2.052,1.948 1.885,1.948 1.885,1.948 1.885,1.365 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.094,1.875 1.583,2.094 0.49,0.219 10 false CGND 2.135,1.865 2.625,2.083 0.49,0.219 10 false CB+ 0.313,1.073 0.802,1.292 0.49,0.219 10 false W15
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W15-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W15-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427510C04
0.25,1.01 0.667,1.313 0.417,0.302 1.552,1.948 1.719,1.948 1.719,1.948 1.719,1.365 true 2.052,1.948 1.885,1.948 1.885,1.948 1.885,1.365 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.094,1.875 1.583,2.094 0.49,0.219 10 false CGND 2.135,1.865 2.625,2.083 0.49,0.219 10 false CB+ 0.313,1.073 0.802,1.292 0.49,0.219 10 false W15
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W15-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W15-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
6.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)