Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for HV Model) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417361 FRONT AIR CONDITIONING UNIT(for HV Model) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for HV Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Steering sensor* Steering angle setting Parking Assist Monitor System (Click here)
Adjust steering angle Panoramic View Monitor System (Click here)
Steering angle neutral point Parking Assist Monitor System (Click here)
Parking Support Brake System (Click here)
Panoramic View Monitor System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 4.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 5.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 6.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 7.REMOVE FRONT FENDER SPLASH SHEILD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 8.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 9.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 10.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 88710G 11.DISCONNECT NO. 2 AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.
E435594

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E435596

Disconnect the No. 2 air conditioner tube and accessory assembly.


c.

Remove the 2 O-rings from the No. 2 air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 87246B 12.DISCONNECT OUTLET HEATER WATER HOSE B

a.
E431222

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose B.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose B.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245B 13.DISCONNECT INLET HEATER WATER HOSE B

a.
E431224

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose B.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose B.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 14.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 15.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 16.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 83108 17.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 87201L 18.REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY

Hide 45250 19.REMOVE STEERING COLUMN ASSEMBLY

Hide 82877 20.REMOVE ECU INTEGRATION BOX RH

Hide 21.REMOVE PARKING ASSIST ECU WITH BRACKET

Hide 88625Q 23.REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR

a.
E431641

Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.


Hide 87212F 26.REMOVE REAR NO. 2 AIR DUCT

a.
E431645

Disengage the 4 guides and turn back the front floor carpet assembly as shown in the illustration.


b.
E431647

Remove the clip.


c.

Disengage the 4 claws and remove the rear No. 2 air duct.


Hide 87212 27.REMOVE REAR NO. 1 AIR DUCT

a.
E431648

Disengage the 4 claws and remove the rear No. 1 air duct.


Hide 87212H 28.REMOVE REAR NO. 4 AIR DUCT

a.
E431649

Disengage the 4 guides and turn back the front floor carpet assembly as shown in the illustration.


b.
E431651

Remove the clip.


c.

Disengage the 4 claws and remove the rear No. 4 air duct.


Hide 87212G 29.REMOVE REAR NO. 3 AIR DUCT

a.
E431652

Disengage the 4 claws and remove the rear No. 3 air duct.


Hide 55215D 30.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
E431653

Remove the No. 3 dash panel insulator pad.

NOTICE:

If the No. 3 dash panel insulator pad is damaged, replace it with a new one.



Hide 55837C 31.REMOVE CENTER HEATER TO REGISTER SUB DUCT

a.
E431654

Remove the 2 screws.


b.

Disengage the guide to remove the center heater to register sub duct.


Hide 32.DISCONNECT INSTRUMENT PANEL WIRE

a.

Disconnect the connector.

E456767C02
0.406,0.271 0.906,0.49 true 4.115,0.5 4.583,0.281 true 5.854,3.292 6.063,3.219 true 0.813,5.438 0.813,5.219 true 5.781,3.958 6.313,3.667 true 6.667,3.125 6.875,3.052 true 0.219,0.167 0.406,0.375 0.188,0.208 10 true *a 4.594,0.167 4.781,0.375 0.188,0.208 10 true *a 5.573,3.854 5.76,4.063 0.188,0.208 10 true *a 0.75,5.438 0.938,5.646 0.188,0.208 10 true *a 5.625,3.208 5.813,3.417 0.188,0.208 10 true *b 6.885,2.938 7.135,3.177 0.25,0.24 12 true *A
*A w/ Airbag Cut Off Switch - -
*a Earth Wire *b Connector Holder
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Connector
V100138

Nut



b.

Remove the 4 bolts (A) and disconnect the 4 earth wires.


c.

Remove the 2 nuts.


d.

Remove the bolt (B) and disconnect the connector holder.


e.

Disengage each clamp.


f.
E434825C01
1.677,2.938 2.5,2.344 true 1.469,2.833 1.781,2.99 0.313,0.156 10 false *a
*a Earth Wire
V100135

Connector
V100136

Bolt


Disconnect the 2 connectors.


g.

Disengage each clamp.


h.

Remove the bolt and disconnect the earth wire.


Hide 55306A 33.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E431657C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 55307C 34.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E431658C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.


Hide 35.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
E431659

Remove the clip.


b.

Disconnect the drain cooler hose.

NOTICE:

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.



c.
E431661

Remove the cooler unit drain hose grommet.


d.
E431663

Remove the 2 hole plugs.


e.
E431664

Remove the 3 bolts.


f.

Remove the 4 bolts (A).

E431665C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Nut - -



g.

Remove the bolt (B) and disconnect the brake pedal assembly.


h.

Remove the nut.


i.

Disengage each clamp.

E431666C01
0,0 0,0 false
V113147

Remove in this Direction - -



j.

Disconnect the 4 connectors.


k.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


Hide 55835A 36.REMOVE CENTER HEATER TO REGISTER DUCT

a.
E431670

Disengage the 6 claws to remove the center heater to register duct.


Hide 37.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and the air conditioner unit assembly from the instrument panel reinforcement assembly.

E431671