Home › Suspension › REAR SUSPENSION › REAR COIL SPRING
RM37A0E _53 Suspension _086866 REAR SUSPENSION _0417438 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear coil spring removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: for RH Side

Rear wheel alignment adjustment
for HV Model

Perform "Calibration".


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leak from exhaust system is repaired*1 Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


for A25A-FXS, A25B-FXS:(Click here)
for 2GR-FKS:(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 17430 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY (for RH Side)

Hide 48738 3.REMOVE REAR SUSPENSION ARM COVER

Hide 4.SEPARATE REAR STABILIZER LINK ASSEMBLY

a.
C426688

Remove the bolt and nut, and separate the rear stabilizer link assembly from the rear No. 2 suspension arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48231B 5.REMOVE REAR COIL SPRING

a.
C426689C01
2.135,0.74 2.135,0.354 2.135,0.354 2.396,0.354 true 0.854,1.74 0.854,1.354 0.854,1.354 1.135,1.354 true 0.865,1.427 1.146,1.427 true 2.146,0.448 2.396,0.448 true 2.073,0.792 2.26,0.948 0.188,0.156 10 true *a 0.792,1.76 1.031,1.927 0.24,0.167 10 true *a
*a Matchmark


Place matchmarks on the rear No. 2 suspension camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.


b.

Loosen the nut (rear suspension member sub-assembly side) of the rear No. 2 suspension arm assembly.

NOTICE:

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.



c.
C426681C01
1.781,1.74 2.229,1.74 true 1.969,2.146 2.208,2.146 false 2.281,1.656 2.5,1.833 0.219,0.177 10 true *a 2.313,2.063 2.625,2.219 0.313,0.156 10 false *b
*a Wooden Block
*b Jack
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C426690

Remove the bolt and nut, and separate the rear No. 2 suspension arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Slowly lower the rear No. 2 suspension arm assembly, and then remove the rear coil spring.


Hide 48258C 6.REMOVE REAR LOWER COIL SPRING INSULATOR

a.
C426692

Remove the rear lower coil spring insulator from the rear No. 2 suspension arm assembly.


Hide 48259A 7.REMOVE REAR UPPER COIL SPRING INSULATOR

a.
C426691

Remove the rear upper coil spring insulator from the spring seat sub-assembly.


Hide 48049A 8.REMOVE SPRING SEAT SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the spring seat sub-assembly is necessary.


a.
C426693

Remove the 3 bolts, and the spring seat sub-assembly from the vehicle.