Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for 4WD/AWD) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0417448 REAR AXLE HUB(for 4WD/AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for 4WD/AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
for HV Model
·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42450B 1.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

a.
C424677C01
2.323,1.625 2.323,0.729 2.323,0.729 2.698,0.729 true 2.333,0.99 2.719,0.99 true 2.26,1.656 2.573,1.833 0.313,0.177 10 false *a
*a Matchmark


Install the rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly to the rear drive shaft assembly.

NOTICE:

Align the matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.



b.

Install the rear axle hub and bearing assembly to the rear axle carrier sub-assembly with the 4 bolts.

Torque:
121 N*m (1234 kgf*cm, 89 ft.*lbf)


Hide 42431 2.INSTALL REAR DISC

Hide 3.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 47850 4.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.

Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:

The bolts can be reused while inspecting the rear axle hub and bearing assembly for looseness and runout. However, make sure to replace the bolts with new ones after the inspection is complete.



Hide 42312B 5.TEMPORARILY INSTALL REAR AXLE SHAFT NUT

a.

Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new rear drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a 30 mm deep socket wrench, temporarily install the rear axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)

NOTICE:

Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Keep depressing the brake pedal to prevent the rear drive shaft assembly from rotating.



Hide 47850 6.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 7.REMOVE REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 42431 8.REMOVE REAR DISC

Hide 42431 11.INSTALL REAR DISC

Hide 12.INSTALL REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 47850 13.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 89544E 14.INSTALL REAR SKID CONTROL SENSOR

a.

Install the rear skid control sensor to the rear axle carrier sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Keep the tip of the rear skid control sensor and installation hole free of foreign matter.

·

Firmly insert the rear skid control sensor body into the rear axle carrier sub-assembly before tightening the bolt.

·

After installing the rear skid control sensor to the rear axle carrier sub-assembly, make sure that there is no clearance between the rear skid control sensor stay and rear axle carrier sub-assembly. Also make sure that no foreign matter is stuck between the parts.




Hide 890C0A 15.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Connect the No. 2 parking brake wire assembly connector to the rear skid control sensor.


b.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


Hide 42312B 16.STAKE REAR AXLE SHAFT NUT

a.
C424680

Using a chisel and hammer, stake the rear axle shaft nut.


Hide 48738 17.INSTALL REAR SUSPENSION ARM COVER

Hide 18.INSTALL REAR WHEEL

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

a.

Connect the reservoir level switch connector.


b.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the bolt and nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Engage the clamp to install the wire harness to the brake master cylinder reservoir assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION


e.

Turn the ignition switch to ON (READY).


f.

Depress the brake pedal and release it.