Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER (for 2WD) › 2020.02–2020.11
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0417449 REAR AXLE CARRIER(for 2WD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Rear wheel alignment adjustment Perform "Calibration".
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL

Hide 2.REMOVE REAR WHEEL

Hide 48738 3.REMOVE REAR SUSPENSION ARM COVER

Hide 47319F 4.SEPARATE REAR FLEXIBLE HOSE

a.
C424684

Remove the bolt and separate the rear flexible hose from the rear upper control arm assembly.


Hide 890C0A 5.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C426038

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




b.
C427323C01
1.24,0.771 1.427,0.438 1.427,0.438 1.667,0.438 true 1.74,0.344 1.969,0.521 0.229,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

·

Be careful not to damage the rear axle hub and bearing assembly or connector cover.




c.
C427602

Remove the bolt and separate the No. 2 parking brake wire assembly from the rear axle carrier sub-assembly.


d.
C424685

Remove the 3 bolts and separate the No. 2 parking brake wire assembly from the rear trailing arm assembly.


Hide 47850 6.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

Hide 7.REMOVE REAR DISC BRAKE CYLINDER MOUNTING WITH BRAKE PAD

Hide 42431 8.REMOVE REAR DISC

Hide 42450B 9.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 48780E 10.REMOVE REAR TRAILING ARM ASSEMBLY

Hide 42305 11.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C424686C01
1.5,2.49 1.865,2.49 false 1.5,3.073 1.865,3.073 false 1.313,2.406 1.625,2.563 0.313,0.156 10 false *a 1.333,3 1.646,3.156 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Keep supporting the rear No. 2 suspension arm assembly until the installation of the rear axle carrier sub-assembly has been completed.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.
C424687N01
2.552,3.094 2.708,3.24 0.156,0.146 10 true A 2.865,3.094 3.031,3.26 0.167,0.167 10 true A 0.729,0.594 0.885,0.74 0.156,0.146 10 true B 2.802,0.177 2.969,0.344 0.167,0.167 10 true C 0.49,2.708 0.688,2.906 0.198,0.198 10 true D

Remove the 2 bolts (A), and separate the rear lower shock absorber bracket sub-assembly from the rear axle carrier sub-assembly.


c.

Remove the bolt (B) and nut, and separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



d.

Remove the bolt (C) and nut, and separate the rear axle carrier sub-assembly from the rear No. 2 suspension arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the nut (D), spacer and rear axle carrier sub-assembly from the rear No. 1 suspension arm assembly.


Hide 48759 12.REMOVE LOWER CONTROL ARM PIN

a.
C428095

Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a hammer, remove the lower control arm pin from the rear axle carrier sub-assembly.