Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL INJECTOR (for Port Injection) › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086907 A25A-FXS, A25B-FXS FUEL _0417782 FUEL INJECTOR(for Port Injection) A

A25A-FXS, A25B-FXS FUEL  FUEL INJECTOR(for Port Injection)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23250F 1.INSTALL PORT FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a port fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of spindle oil or gasoline to 4 new O-rings, and install one to each port fuel injector assembly.

NOTICE:

Check that there is no damage or foreign matter on the groove of the port fuel injector assembly when installing the O-ring to each port fuel injector assembly.



b.
A401656C01
1.531,1.76 1.75,1.76 1.75,1.76 2.198,1.385 true 2.281,1.271 2.458,1.104 2.458,1.104 2.604,1.104 false 2.281,1.385 2.521,1.281 2.521,1.281 2.677,1.281 false 2.719,1.198 3.031,1.354 0.313,0.156 10 false *a 1.365,1.677 1.677,1.833 0.313,0.156 10 false *b 2.656,1.021 2.969,1.177 0.313,0.156 10 false *b
*a Stopper
*b Claw


Install the 4 port fuel injector assemblies to the fuel delivery pipe sub-assembly.

NOTICE:
·

Make sure that the port fuel injector assembly is located within the stopper as shown in the illustration.

·

Check that the port fuel injector assembly installation holes of the fuel delivery pipe sub-assembly are not damaged and are free of foreign matter.

·

Make sure that the O-ring is not damaged, twisted or moved out of place when installing the port fuel injector assembly.




Hide 82125N 2.INSTALL NO. 5 ENGINE WIRE

a.

Engage the 2 clamps to install the No. 5 engine wire to the fuel delivery pipe sub-assembly.


b.

Connect the 4 port fuel injector assembly connectors and No. 2 fuel pressure sensor connector.


Hide 23291 3.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 4 new injector vibration insulators to the cylinder head sub-assembly.


Hide 23807V 4.INSTALL NO. 1 DELIVERY PIPE SPACER

a.
A408580C02
1.958,1.271 2.271,1.427 0.313,0.156 10 false *a 1.948,1.885 2.26,2.042 0.313,0.156 10 false *b
*a Fuel Delivery Pipe Sub-assembly Side
*b Cylinder Head Sub-assembly Side


Install the 2 No. 1 delivery pipe spacers to the cylinder head sub-assembly.

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



Hide 23807 5.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Place the fuel delivery pipe sub-assembly with the 4 port fuel injector assemblies onto the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when installing the fuel delivery pipe sub-assembly.



b.

Install the fuel delivery pipe sub-assembly with the port fuel injector assemblies with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


c.

Connect the No. 5 engine wire connector.


Hide 23100X 6.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23801P 7.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

NOTICE:

Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.


a.

for Cylinder Head Cover Sub-assembly Connection Type:

i.

Temporarily install the bolt.



b.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel delivery pipe and tighten the union nut by hand.


c.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.


Hide 23100X 8.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23801P 9.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

for EGR Valve Bracket Connection Type:

i.
A456261C01
2.729,2.698 2.729,2.531 2.729,2.531 2.896,2.531 false 2.979,2.448 3.292,2.646 0.313,0.198 10 false *a 1.646,2.302 1.958,2.5 0.313,0.198 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




ii.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)





b.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A474163C01
2.74,2.688 2.74,2.521 2.74,2.521 2.906,2.521 false 2.979,2.427 3.292,2.625 0.313,0.198 10 false *a 1.677,2.281 1.99,2.479 0.313,0.198 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




ii.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




iii.

Using an 8 mm socket wrench, tighten the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

Connect the ignition coil connector.


Hide 23910A 10.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pump assembly and fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector.


Hide 22030 13.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441L 15.INSTALL BATTERY SERVICE HOLE COVER

Hide 17.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a port fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION