Refer to DTC P003012.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P003012
Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P219519 | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit ·
Air fuel ratio sensor (Bank 1 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2195 |
| P219524 | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck High | Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.
Air fuel ratio sensor voltage is higher than 3.8 V. 2.
Heated oxygen sensor voltage is 0.21 V or higher. |
·
Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit ·
Air fuel ratio sensor (Bank 1 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2195 |
| P219618 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.47 mA for 3 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit ·
Air fuel ratio sensor (Bank 1 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2196 |
| P219623 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck Low | Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.
Air fuel ratio sensor voltage is less than 2.8 V. 2.
Heated oxygen sensor voltage is less than 0.71 V. |
·
Open or short in air fuel ratio sensor (Bank 1 sensor 1) circuit ·
Air fuel ratio sensor (Bank 1 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2196 |
| P219719 | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Circuit Current Above Threshold | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit ·
Air fuel ratio sensor (Bank 2 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2197 |
| P219724 | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Signal Stuck High | Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.
Air fuel ratio sensor voltage is higher than 3.8 V. 2.
Heated oxygen sensor voltage is 0.21 V or higher. |
·
Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit ·
Air fuel ratio sensor (Bank 2 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2197 |
| P219818 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Circuit Current Below Threshold | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.47 mA for 3 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit ·
Air fuel ratio sensor (Bank 2 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2198 |
| P219823 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Signal Stuck Low | Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.
Air fuel ratio sensor voltage is less than 2.8 V. 2.
Heated oxygen sensor voltage is less than 0.71 V. |
·
Open or short in air fuel ratio sensor (Bank 2 sensor 1) circuit ·
Air fuel ratio sensor (Bank 2 sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly (for port injection) ·
Fuel injector assembly (for direct injection) ·
Fuel system ·
ECM |
Comes on | DTC stored | SAE Code: P2198 |
DTCs P219519, P219524, P219618 and P219623 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
DTCs P219719, P219724, P219818 and P219823 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
When any of these DTCs are stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine / Data List / A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1.
Short-term fuel trim values can also be read using the GTS.
The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the GTS.
If an air fuel ratio sensor malfunction is detected, the ECM will store a DTC.
Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.7 V, the ECM stores DTC P219623 or P219823. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P219524 or P219724 is stored.
A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.
If the air fuel ratio sensor output is 2.2 mA or higher for 3 seconds or more of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P219519 or 219719 (stuck on high side). If the air fuel ratio sensor output is less than 0.47 mA for 3 seconds or more of cumulative time, the ECM stores DTC P219618 or P219818 (stuck on low side).
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Heated oxygen sensor |
| Frequency of Operation | Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor |
| Duration | 3 seconds: Sensor current detection monitor
5 seconds: Sensor voltage detection monitor |
| Time after engine start | 30 seconds or more |
| Battery voltage | 11 V or higher |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed-loop |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [11 psi(abs)] or higher |
| Air fuel ratio sensor status | Activated |
| Continuous time of fuel-cut | 3 seconds or more, and less than 10 seconds |
| Heated oxygen sensor voltage | 0.21 V or higher |
| Air fuel ratio sensor voltage | Higher than 3.8 V |
| Heated oxygen sensor voltage | Less than 0.71 V |
| Air fuel ratio sensor voltage | Less than 2.8 V |
| Duration of following condition | 3 seconds or more |
| Air fuel ratio sensor current | 2.2 mA or higher |
| Duration of following condition | 3 seconds or more |
| Air fuel ratio sensor current | Less than 0.47 mA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Drive the vehicle at a speed between 60 and 120 km/h (37 and 75 mph) for at least 10 minutes [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
With the shift lever in M [C], accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Soon after performing step [D] above, release the accelerator pedal for at least 5 seconds without depressing the brake pedal in order to execute fuel-cut control [E].
Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
Repeat steps [C] through [E] above at least 3 times in one driving cycle.
Enter the following menus: Powertrain / Engine / Trouble Codes [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [F] again.
Refer to DTC P003012.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P003012
Inspect the fuses for circuits related to this system before performing the following procedure.
A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output | A |
| DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 and P013611, P013613, P013614, P013615, P013617, P013623, P01361C, P015611, P015613, P015614, P015615, P015617, P015623 or P01561C are output | |
| DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 and other DTCs are output | B |
If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.
A
B
Has the vehicle run out of fuel in the past?
| Proceed to |
|---|
| YES |
| NO |
YES
NO
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Check the DTC judgment result.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output) |
B |
A
B
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Check the test value of the air fuel ratio sensor output (sensor 1) current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.
| Tester Display |
|---|
| A/F (O2) Sensor Current B1S1 |
| A/F (O2) Sensor Current B2S1 |
To measure the air fuel ratio sensor (sensor 1) current precisely, perform the fuel-cut operation as long as possible.
If it is difficult to measure the air fuel ratio sensor (sensor 1) current, use the snapshot function of the GTS.
| Test Value | Proceed to |
|---|---|
| Within normal range
(0.47 mA or higher, and less than 2.2 mA) |
A |
| Outside normal range
(Less than 0.47 mA, or 2.2 mA or higher) |
B |
A
B
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
| Tester Display |
|---|
| Coolant Temperature |
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| A/F (O2) Sensor Voltage B1S1 |
| A/F (O2) Sensor Voltage B2S1 |
| O2 Sensor Voltage B1S2 |
| O2 Sensor Voltage B2S2 |
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1 (Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2 (Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 | Status of O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
|---|---|---|---|
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | |
| Lean/Rich | Lean/Rich | Normal |
Lean: During the Control the Injection Volume for A/F Sensor of the Active Test, the air fuel ratio sensor output voltages (A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1) are consistently higher than 3.4 V, and the heated oxygen sensor output voltages (O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2) are consistently below 0.4 V.
Rich: During the Control the Injection Volume for A/F Sensor of the Active Test, the A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1 are consistently below 3.1 V, and the O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2 are consistently higher than 0.55 V.
Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1, A/F (O2) Sensor Voltage B2S1, O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2].
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
A
B
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from the intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leaks.
No gas leaks in exhaust system.
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly (for port injection) (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL INJECTOR (for Port Injection)>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection).
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.
| Tester Display |
|---|
| Coolant Temperature |
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Engine Speed |
| Fuel Pressure (High) |
| Injection Mode |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Fuel Pressure (High) | ·
Shift position: P ·
A/C: Off ·
Engine warmed up ·
Engine Speed: 3000 rpm ·
Injection Mode: Direct |
2400 to 20000 kPag |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL INJECTOR (for Direct Injection)>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection).
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Check the DTC judgment result.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output) |
B |
A
B
Check the fuel lines for leaks or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Check the DTC judgment result.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output) |
B |
A
B