This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, power window regulator motor assembly (driver door), power window regulator motor assembly (front passenger door), power window regulator motor assembly (rear RH door), power window regulator motor assembly (rear LH door), sliding roof ECU (sliding roof drive gear assembly)*1*2 or roof sunshade ECU (sliding roof drive gear assembly)*2 stops for 10 seconds or more.
*1: w/ Sliding Roof System
*2: w/ Panoramic Moon Roof System
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1206 | P/W Master Switch Communication Stop | No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Multiplex network master switch assembly ·
Wire harness or connector ·
ECU-B NO. 2 fuse |
| B1273 | Sliding Roof ECU Communication Stop | No communication between sliding roof ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.*1*2 | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Sliding roof ECU (sliding roof drive gear assembly) ·
Wire harness or connector ·
S/ROOF fuse |
| B2321 | D-Door Motor ECU Communication Stop | No communication between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Multiplex network master switch assembly ·
Power window regulator motor assembly (driver door) ·
Wire harness or connector ·
DOOR F/L fuse |
| B2322 | P-Door Motor ECU Communication Stop | No communication between power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Power window regulator motor assembly (front passenger door) ·
Wire harness or connector ·
DOOR F/R fuse |
| B2323 | RR-Door Motor ECU Communication Stop | No communication between power window regulator motor assembly (rear RH door) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Power window regulator motor assembly (rear RH door) ·
Wire harness or connector ·
DOOR R/R fuse |
| B2324 | RL-Door Motor ECU Communication Stop | No communication between power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Power window regulator motor assembly (rear LH door) ·
Wire harness or connector ·
DOOR R/L fuse |
| B2329 | Lost Communication with Sliding Sunshade ECU | No communication between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.*2 | ·
Roof sunshade ECU (sliding roof drive gear assembly) ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Wire harness or connector ·
SHADE fuse |
*1: w/ Sliding Roof System
*2: w/ Panoramic Moon Roof System
Inspect the fuses for circuits related to this system before performing the following procedure.
When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*
w/ Sliding Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
w/ Panoramic Moon Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
*: w/ Sliding Roof System or Panoramic Moon Roof System
When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
*: w/ Panoramic Moon Roof System
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC B1206, B1273*1*2, B2321, B2322, B2323, B2324 and B2329*2 are output | B |
| DTC B1206, B1273*1*2, B2321, B2322 and B2329*2 are output | C |
| DTC B2323 and B2324 are output | D |
| Only DTC B1206 and B2321 are output | E |
| Only DTC B1206 is output | F |
| Only DTC B1273 is output*1*2 | G |
| Only DTC B2321 is output | H |
| Only DTC B2322 is output | I |
| Only DTC B2323 is output | J |
| Only DTC B2324 is output | K |
| Only DTC B1273 and B2329 are output*2 | L |
| Only DTC B2329 is output*2 | M |
*1: w/ Sliding Roof System
*2: w/ Panoramic Moon Roof System
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
F
G
H
I
J
K
L
M
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-16 (LIN2) - 4B-17 or 4D-25 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-16 (LIN2) - 4B-17 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J18 multiplex network master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - J18-17 (LIN1) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-16 (LIN2) - 4D-25 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K9 power window regulator motor assembly (rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-25 - K9-9 (LIN) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Disconnect the J18 multiplex network master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - J18-17 (LIN1) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J18-11 (B) - J18-12 (GND) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J18-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Disconnect the R2*1 or R19*2 sliding roof ECU (sliding roof drive gear assembly) connector.
*1: w/ Sliding Roof System
*2: w/ Panoramic Moon Roof System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - R2-7 (MPX1) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - R19-11 (MPX1) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-1 (B) - R2-2 (E) | Ignition switch off*1
Always*2 |
11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R19-8 (B) - R19-12 (E) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R19-12 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
w/ Sliding Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Moon Roof)>DISASSEMBLY
w/ Panoramic Moon Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>DISASSEMBLY
NG
| *a | Component without harness connected
(Multiplex Network Master Switch Assembly) |
Remove the multiplex network master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 16 - 17 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J24 power window regulator motor assembly (driver door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J18-16 (LIN2) - J24-9 (LIN) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J24-2 (B) - J24-1 (GND) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J24-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Disconnect the J8 power window regulator motor assembly (front passenger door) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - J8-9 (LIN) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J8-2 (B) - J8-1 (GND) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J8-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4D instrument panel junction block assembly connector.
Disconnect the K4 power window regulator motor assembly (rear RH door) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-25 - K4-9 (LIN) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-2 (B) - K4-1 (GND) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4D instrument panel junction block assembly connector.
Disconnect the K9 power window regulator motor assembly (rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-25 - K9-9 (LIN) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K9-2 (B) - K9-1 (GND) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K9-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Disconnect the R19 sliding roof ECU (sliding roof drive gear assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - R19-11 (MPX1) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Disconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-17 - R20-11 (MPX1) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R20-8 (B) - R20-12 (E) | Ignition switch off*1
Always*2 |
11 to 14 V |
*1: for HV Model
*2: for Gasoline Model
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R20-12 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG