Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2020.02–2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0418857 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B2325 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Power window regulator motor assembly (driver door)

·

Power window regulator motor assembly (front passenger door)

·

Power window regulator motor assembly (rear LH door)

·

Power window regulator motor assembly (rear RH door)

·

Sliding roof ECU (sliding roof drive gear assembly)*1*2

·

Roof sunshade ECU (sliding roof drive gear assembly)*2

·

Wire harness or connector



*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System


WIRING DIAGRAM

B573069E01
5.646,1.458 6.021,1.656 0.375,0.198 10 false LIN2 1.177,1.156 1.563,1.365 0.385,0.208 10 false LIN2 1.094,2.563 1.531,2.75 0.438,0.188 10 false GND1 5.656,4.615 6.229,4.958 0.573,0.344 10 false LIN 5.469,4.438 5.708,4.656 0.24,0.219 10 false 9 5.656,2.948 5.896,3.167 0.24,0.219 10 false LIN 5.406,1.01 5.646,1.229 0.24,0.219 10 false 17 0.104,3.156 1.74,3.896 1.635,0.74 10 false Main Body ECU (Multiplex Network Body ECU) 1.885,2.979 2.958,3.667 1.073,0.688 10 false Instrument Panel Junction Block Assembly 4.521,3.5 7.115,4.052 2.594,0.552 10 false Power Window Regulator Motor Assembly (Driver Door) 5.292,1.917 6.875,2.406 1.583,0.49 10 false Multiplex Network Master Switch Assembly 4.552,5.125 7.125,5.708 2.573,0.583 10 false Power Window Regulator Motor Assembly (Front Passenger Door) 5.656,1.167 6,1.385 0.344,0.219 10 false LIN1 0.625,8.531 2.552,8.833 1.927,0.302 10 false : LIN Communication Line 2.292,4.438 2.5,4.656 0.208,0.219 10 false 9 0.552,6.802 3.125,7.385 2.573,0.583 10 false Power Window Regulator Motor Assembly (Rear RH Door) 1.958,6.24 2.396,6.635 0.438,0.396 10 false LIN 0.542,5.146 3.115,5.729 2.573,0.583 10 false Power Window Regulator Motor Assembly (Rear LH Door) 2,4.594 2.438,4.99 0.438,0.396 10 false LIN 5.406,1.344 5.646,1.563 0.24,0.219 10 false 16 5.302,1.771 5.667,2 0.365,0.229 10 false J18 4.531,3.344 4.896,3.573 0.365,0.229 10 false J24 5.469,2.781 5.708,3 0.24,0.219 10 false 9 4.552,4.969 4.917,5.198 0.365,0.229 10 false J8 2.927,0.958 3.167,1.177 0.24,0.219 10 false 17 2.927,1.667 3.167,1.885 0.24,0.219 10 false 25 2.958,2.385 3.406,2.708 0.448,0.323 10 false 3 2.906,1.167 3.146,1.385 0.24,0.219 10 false 4B 2.906,1.865 3.146,2.083 0.24,0.219 10 false 4D 2.906,2.573 3.146,2.792 0.24,0.219 10 false 4B 1.573,1.167 1.813,1.385 0.24,0.219 10 false MB 1.594,2.563 1.833,2.781 0.24,0.219 10 false MB 1.604,0.969 1.844,1.188 0.24,0.219 10 false 16 1.615,2.375 1.854,2.594 0.24,0.219 10 false 11 0.552,4.99 0.917,5.219 0.365,0.229 10 false K9 2.292,6.083 2.5,6.302 0.208,0.219 10 false 9 0.563,6.635 0.927,6.865 0.365,0.229 10 false K4 4.208,6.406 4.417,6.625 0.208,0.219 10 false A

B567002E01
0.698,5.375 4.365,5.573 3.667,0.198 10 false : LIN Communication Line 3.167,5.042 7.146,5.24 3.979,0.198 10 false *1: w/ Sliding Roof System 3.167,5.365 7.146,5.563 3.979,0.198 10 false *2: w/ Panoramic Moon Roof System 5.052,3.427 5.667,3.625 0.615,0.198 10 false MPX1 4.646,1.875 5.01,2.104 0.365,0.229 10 false R19 5.052,1.406 5.667,1.604 0.615,0.198 10 false MPX1 1.708,1.417 2.323,1.615 0.615,0.198 10 false MPX1 4.792,1.271 5.031,1.479 0.24,0.208 10 false 11 2.156,1.26 2.313,1.458 0.156,0.198 10 false 7 3.24,0.427 3.396,0.625 0.156,0.198 10 false A 0.615,2.042 2.531,2.833 1.917,0.792 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*1 4.646,2.031 6.563,2.823 1.917,0.792 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*2 4.677,4.042 6.479,4.906 1.802,0.865 10 false Roof Sunshade ECU (Sliding Roof Drive Gear Assembly)*2 4.792,3.292 5.031,3.5 0.24,0.208 10 false 11 4.677,3.875 5.042,4.104 0.365,0.229 10 false R20 0.625,1.875 0.99,2.104 0.365,0.229 10 false R2

CAUTION / NOTICE / HINT

NOTICE:
·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*

w/ Sliding Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

w/ Panoramic Moon Roof System: Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

*: w/ Sliding Roof System or Panoramic Moon Roof System


·

When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION

*: w/ Panoramic Moon Roof System


·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
a.

Disconnect the J24 power window regulator motor assembly (driver door) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

2.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

2.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the J18 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

B

12.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
3.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
a.

Disconnect the J8 power window regulator motor assembly (front passenger door) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

4.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

4.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)
a.

Disconnect the K4 power window regulator motor assembly (rear RH door) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

5.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)
a.

Disconnect the K9 power window regulator motor assembly (rear LH door) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

6.SYSTEM CHECK

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

6.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Sliding Roof System or Panoramic Moon Roof System A
w/o Sliding Roof System and Panoramic Moon Roof System B



A

7.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
7.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Disconnect the R2*1 or R19*2 sliding roof ECU (sliding roof drive gear assembly) connector.

*1: w/ Sliding Roof System

*2: w/ Panoramic Moon Roof System



b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Panoramic Moon Roof System) A
DTC B2325 is output (w/o Panoramic Moon Roof System) B
DTC B2325 is not output C



A

8.CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

C

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

8.CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Disconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

B

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
a.

Disconnect the 4B and 4D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-17 - Body ground Always 10 kΩ or higher
4B-17 - Other terminals Always 10 kΩ or higher
4D-25 - Body ground Always 10 kΩ or higher
4D-25 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

B567934C01
1.875,1.25 2.292,1.552 0.417,0.302 5.479,0.344 5.896,0.646 0.417,0.302 5.51,2.188 5.927,2.49 0.417,0.302 2.208,2.438 2.01,2.438 2.01,2.438 2.01,1.906 true 1.979,1.323 2.292,1.521 0.313,0.198 10 false MB 5.594,0.406 5.906,0.604 0.313,0.198 10 false 4B 5.625,2.25 5.938,2.448 0.313,0.198 10 false 4D 2.26,2.344 2.875,2.542 0.615,0.198 10 false LIN2 0.26,0.156 0.604,0.375 0.344,0.219 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4B-17 or 4D-25 - 4B-3 Always 10 kΩ or higher
MB-16 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

11.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


b.

Connect all instrument panel junction block assembly connectors other than 4B and 4D.

B520182C09
2.896,3.302 3.25,3.51 0.354,0.208 1.115,1.521 1.469,1.729 0.354,0.208 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 4.698,0.917 5.01,1.073 0.313,0.156 10 false *b 4.458,2.458 5.146,2.854 0.688,0.396 10 false GND 3,3.323 3.688,3.719 0.688,0.396 10 false 4B 1.208,1.542 1.896,1.938 0.688,0.396 10 false 4D
*a Component with harness connected
(Instrument Panel Junction Block Assembly)
*b Waveform



c.

Using a GTS, check the waveform.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


OK:
Tester Connection Condition Tool Setting Specified Condition
4B-17 - Body ground Ignition switch ON 2 V/DIV., 200 ms/DIV. Pulse generation
(See waveform)
4D-25 - Body ground Ignition switch ON 2 V/DIV., 200 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

12.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J18-16 (LIN2) - Body ground Always 10 kΩ or higher
J18-16 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR