Home › Engine / Hybrid System › 2GR-FKS (COOLING) › RADIATOR
RM37A0E _51 Engine / Hybrid System _086855 2GR-FKS COOLING _0419161 RADIATOR G

2GR-FKS COOLING  RADIATOR  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A370839

Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A344783

To prevent burns, do not touch the engine or other high temperature components while the engine is hot.



PROCEDURE

Hide 16401 1.CHECK RADIATOR CAP SUB-ASSEMBLY

CAUTION:

Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.
A107446C03
0.479,1.031 0.698,1.229 0.219,0.198 10 false *a 0.708,1.333 1.021,1.49 0.313,0.156 10 false *b 1,1.604 1.313,1.76 0.313,0.156 10 false *c 2.344,1.573 2.656,1.729 0.313,0.156 10 false *d
*a Rubber Packing (1)
*b Rubber Packing (2)
*c Rubber Packing (3)
*d Valve Seat


Measure the valve opening pressure.

i.

If there are water stains or foreign matter on the rubber packing (1), (2) or (3), clean the part(s) with water and finger scouring.


ii.

Check that the rubber packings (1), (2) and (3) are not deformed, cracked or swollen.


iii.

Check that the rubber packing (3) and valve seat are not stuck together.


iv.

Apply engine coolant to the rubber packings (2) and (3) before using a radiator cap tester.


v.
A104601C11
0.375,0.896 0.375,1.521 false 1.719,0.823 1.885,0.365 1.885,0.365 2.094,0.365 false 2.146,0.281 2.323,0.479 0.177,0.198 10 false *a 1.333,0.958 1.531,1.146 0.198,0.188 10 true *b 0.302,1.573 0.479,1.771 0.177,0.198 10 false *1
*1 Radiator Cap Sub-assembly
*a Radiator Cap Tester
*b 30° or more


When using the radiator cap tester, tilt it upward 30° or more.


vi.

Pump the radiator cap tester several times, and check the maximum pressure.

Pumping Speed:

1 pump per second


Result:
Item Specified Condition
Standard pressure
(for brand-new radiator cap sub-assembly)
74 to 103 kPa (0.8 to 1.1 kgf/cm2, 10.7 to 14.9 psi)
Minimum pressure
(for used radiator cap sub-assembly)
59 kPa (0.6 kgf/cm2, 8.6 psi)


HINT:

Even if the radiator cap sub-assembly cannot maintain the maximum pressure, it is not a defect.


If the maximum pressure is less than the minimum pressure, replace the radiator cap sub-assembly.



Hide 2.CHECK RADIATOR ASSEMBLY FOR CLOGGING

CAUTION:

To prevent burns, do not touch the engine or other high temperature components while the engine is hot.


a.

Remove the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL


b.

Remove the inlet air cleaner assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


c.

Shine an electric light at the radiator assembly from the front and check the radiator assembly for clogging using a mirror.

A455584C01
1.208,0.521 1.656,0.521 false 2.323,0.521 2.938,0.521 false 5.385,1.333 5.917,0.896 5.917,0.896 5.438,0.74 false 4.604,1.271 3.99,0.948 3.99,0.948 4.542,0.76 false 1.646,2.146 1.906,2.385 0.26,0.24 10 true *a 3.833,2.167 4.073,2.365 0.24,0.198 10 true *b 1.063,0.427 1.375,0.583 0.313,0.156 10 false *c 2.979,0.448 3.292,0.604 0.313,0.156 10 false *d 5.958,0.802 6.271,0.958 0.313,0.156 10 false *e 3.813,0.844 4.125,1 0.313,0.156 10 false *e
*a OK *b NG
*c Electric Light *d Mirror
*e Areas to be checked - -


OK:

The radiator assembly is not clogged.


If the radiator assembly is clogged, clean it.


d.

e.

Install the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION


Hide 3.CLEAN RADIATOR ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine or other high temperature components while the engine is hot.


a.

Remove the No. 2 radiator air guide.

Click hereEngine / Hybrid System>2GR-FKS (COOLING)>RADIATOR>REMOVAL


b.

Cover the opening of each air duct with a piece of cloth.


c.

Clean the cooler condenser assembly.

i.

Check that the washer nozzle is not clogged.


ii.
A455585

Insert the washer nozzle into the space in front and spray it.

NOTICE:
·

Clean the fins of the cooler condenser assembly by spraying the entire area for 150 seconds. Repeat this process twice.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the cooler condenser assembly.

·

Do not allow the nozzle to contact the fins of the cooler condenser assembly.

·

Keep the nozzle moving while spraying water.

·

Do not spray the cooler compressor assembly or generator assembly excessively.




iii.

Leave the cooler condenser assembly as is for 10 minutes to let the water penetrate the dirt.


iv.

Clean the cooler condenser assembly again.

NOTICE:
·

Clean the fins of the cooler condenser assembly by spraying the entire area for 150 seconds. Repeat this process 4 times.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the cooler condenser assembly.

·

Do not allow the nozzle to contact the fins of the cooler condenser assembly.

·

Keep the nozzle moving while spraying water.

·

Do not spray the cooler compressor assembly or generator assembly excessively.




v.

Using an air blow gun, dry the cooler condenser assembly for 3 minutes.



d.
A455602

Disconnect the cooling fan motor connector.


e.

Disengage the clamp to disconnect the wire harness from the fan with motor assembly.


f.
A455603

Rotate the lever while pushing the lock, and disconnect the cooling fan motor connector.

NOTICE:

After disconnecting the cooling fan motor connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the cooling fan motor connector.



g.

Disengage the 2 clamps to disconnect the wire harness from the fan with motor assembly.


h.
A456947

Disengage the 2 claws and separate the fan with motor assembly from the radiator assembly.


i.

Clean the radiator assembly.

i.
A455586

Insert the washer nozzle between the radiator assembly and fan with motor assembly and spray the radiator assembly.

NOTICE:
·

Clean the fins of the radiator assembly by spraying the entire area for 150 seconds. Repeat this process twice.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the radiator assembly.

·

Do not allow the nozzle to contact the fins of the radiator assembly.

·

Keep the nozzle moving while spraying water.




ii.

Leave the radiator assembly as is for 10 minutes to let the water penetrate the dirt.


iii.

Clean the radiator assembly again.

NOTICE:
·

Clean the fins of the radiator assembly by spraying the entire area for 150 seconds. Repeat this process 4 times.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the radiator assembly.

·

Do not allow the nozzle to contact the fins of the radiator assembly.

·

Keep the nozzle moving while spraying water.




iv.

Using an air blow gun, dry the radiator assembly for 3 minutes.



j.

Check the fins of the radiator assembly for clogs again.

If the radiator assembly is clogged, clean the cooler condenser assembly and radiator assembly again.


k.
A455606

Check that the 2 guides at the bottom are engaged to the radiator assembly.


l.

Engage the 2 claws to install the fan with motor assembly to the radiator assembly.


m.
A455604

Engage the 2 clamps to connect the wire harness to the fan with motor assembly.


n.

Connect the cooling fan motor connector and rotate the lever to lock it.

NOTICE:
·

When connecting the cooling fan motor connector, make sure that the connecting parts of the cooling fan motor connector are free of dirt, water and other foreign matter.

·

Be sure to securely connect the cooling fan motor connector.




o.

Engage the clamp to connect the wire harness to the fan with motor assembly.


p.

Connect the cooling fan motor connector.


q.

Remove the piece of cloth from the opening of each air duct.


r.

Install the No. 2 radiator air guide.

Click hereEngine / Hybrid System>2GR-FKS (COOLING)>RADIATOR>INSTALLATION