Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  TRAIL Switch Circuit  


DESCRIPTION

The TRAIL mode switch signal will be sent to the hybrid vehicle control ECU when the TRAIL mode switch is operated. If the specified conditions are met, the system enters TRAIL mode and the vehicle will be driven using TRAIL mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the TRAIL mode indicator.

WIRING DIAGRAM

A376617E54
1.49,1.25 3.438,1.563 1.948,0.313 10 false Combination Meter Assembly 2.24,1.896 3,2.083 0.76,0.188 10 false TRAIL 1.219,2.885 3.958,3.24 2.74,0.354 10 false TRAIL Mode Switch (Pattern Select Switch) 4.74,2.958 6.802,3.427 2.063,0.469 10 false Hybrid Vehicle Control ECU 5.104,2.063 5.688,2.323 0.583,0.26 10 false ALSD 4.802,2.063 5.083,2.344 0.281,0.281 10 false 36 4.76,2.771 5.042,3.052 0.281,0.281 10 false H67 1.229,2.708 1.51,2.99 0.281,0.281 10 false P8 5.76,1.635 6.042,1.917 0.281,0.281 10 false +B 1.552,2.063 1.833,2.344 0.281,0.281 10 false 2 1.75,2.063 2.219,2.375 0.469,0.313 10 false E 3,2.073 3.281,2.354 0.281,0.281 10 false B 3.198,2.073 3.479,2.354 0.281,0.281 10 false 5 0.583,3.385 2.531,3.698 1.948,0.313 10 false : CAN Communication Line

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Pattern Select Switch EV Mode Circuit

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)

A

3.READ VALUE USING GTS (AUTO LSD SWITCH)

B

GO TO DTC CHART

3.READ VALUE USING GTS (AUTO LSD SWITCH)
a.

Read the Data List using the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
Auto LSD Switch
50003 397 646
Result:
Result Proceed to
GTS display changes according to TRAIL mode switch operation A
GTS display does not change according to TRAIL mode switch operation B



b.

Turn the ignition switch off.



A

B

4.INSPECT TRAIL MODE SWITCH (PATTERN SELECT SWITCH)
4.INSPECT TRAIL MODE SWITCH (PATTERN SELECT SWITCH)

OK

5.CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH - BODY GROUND)

NG

REPLACE TRAIL MODE SWITCH (PATTERN SELECT SWITCH)

5.CHECK HARNESS AND CONNECTOR (TRAIL MODE SWITCH - BODY GROUND)
a.

Disconnect the P8 TRAIL mode switch (pattern select switch) connector.


b.
A443440C01
1.5,0.188 1.865,0.385 0.365,0.198 1.25,1.781 1.458,1.344 true 1.583,0.208 2.042,0.406 0.458,0.198 10 false P8 1.156,1.792 1.615,1.99 0.458,0.198 10 false E 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to TRAIL Mode Switch (Pattern Select Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-2 (E) - Body ground Always Below 1 Ω



c.

Reconnect the P8 TRAIL mode switch (pattern select switch) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRAIL MODE SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRAIL MODE SWITCH)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Disconnect the P8 TRAIL mode switch (pattern select switch) connector.


c.
A443447C01
1.521,0.177 1.927,0.438 0.406,0.26 1.521,2.365 1.927,2.625 0.406,0.26 2.302,3.99 1.969,3.552 true 2.323,2.01 2.125,1.563 true 1.604,0.219 2.063,0.417 0.458,0.198 10 false H67 1.635,2.427 2.094,2.625 0.458,0.198 10 false P8 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.167,2.281 0.479,2.438 0.313,0.156 10 false *b 2.365,3.99 2.521,4.188 0.156,0.198 10 false B 2.292,2.031 2.802,2.313 0.51,0.281 10 false ALSD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to TRAIL Mode Switch (Pattern Select Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-36 (ALSD) - P8-5 (B) Always Below 1 Ω
H67-36 (ALSD) or P8-5 (B) - Body ground Always 10 kΩ or higher



d.

Reconnect the P8 TRAIL mode switch (pattern select switch) connector.


e.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR