Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD)
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  Drive Mode Select Switch Circuit  


DESCRIPTION

When the drive mode select switch is operated, a switch signal is sent to the hybrid vehicle control ECU, then the hybrid vehicle control ECU changes the drive mode.

WIRING DIAGRAM

A409137E07
0.927,4.333 3.219,4.625 2.292,0.292 10 false : CAN Communication Line 1.604,3.729 4.219,4.469 2.615,0.74 10 false Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly) 5.031,3.802 6.917,4.427 1.885,0.625 10 false Hybrid Vehicle Control ECU 1.781,1.177 4.073,1.375 2.292,0.198 10 false Combination Meter Assembly 5.448,2.625 5.948,2.875 0.5,0.25 10 false DMS+ 5.448,3.115 5.948,3.365 0.5,0.25 10 false DMS- 1.604,3.583 2.063,3.781 0.458,0.198 10 false P3 5.031,3.635 5.49,3.833 0.458,0.198 10 false H67 1.958,3 2.188,3.271 0.229,0.271 10 false E 3.271,2.521 3.833,2.771 0.563,0.25 10 false SEL 3.417,3.031 3.979,3.281 0.563,0.25 10 false E 1.74,3 1.896,3.198 0.156,0.198 10 false 5 3.656,2.531 3.813,2.729 0.156,0.198 10 false 7 3.646,3.031 3.802,3.229 0.156,0.198 10 false 6 5.135,2.5 5.448,2.698 0.313,0.198 10 false 38 5.146,3.031 5.458,3.229 0.313,0.198 10 false 37

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>Pattern Select Switch EV Mode Circuit

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)

A

3.CHECK DRIVE MODE STATUS

B

GO TO DTC CHART

3.CHECK DRIVE MODE STATUS
a.

Turn the ignition switch to ON.


b.

Operate the drive mode select switch (No. 1 pattern select switch assembly) to change the drive mode.


c.

Check that the drive mode indicator is displayed on the multi-information display and changes according to the selected drive mode.

Result:
Result Proceed to
Display changes according to drive mode select switch operation A
Display does not change according to drive mode select switch operation B



d.

Turn the ignition switch off.



A

B

4.READ VALUE USING GTS (DRIVE MODE SWITCH-, DRIVE MODE SWITCH+)
4.READ VALUE USING GTS (DRIVE MODE SWITCH-, DRIVE MODE SWITCH+)
a.

Read the Data List using the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
Drive Mode Switch-
Drive Mode Switch+
50003 397 640,641
Result:
Result Proceed to
GTS display changes according to drive mode select switch operation A
Other than above B



b.

Turn the ignition switch off.



A

B

5.INSPECT DRIVE MODE SELECT SWITCH (NO. 1 PATTERN SELECT SWITCH ASSEMBLY)
5.INSPECT DRIVE MODE SELECT SWITCH (NO. 1 PATTERN SELECT SWITCH ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH - BODY GROUND)

NG

REPLACE DRIVE MODE SELECT SWITCH (NO. 1 PATTERN SELECT SWITCH ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH - BODY GROUND)
a.

Disconnect the P3 drive mode select switch (No. 1 pattern select switch assembly) connector.


b.
A368640C11
0.417,1.031 0.833,1.271 0.417,0.24 1.104,1.823 1.375,1.5 true 0.188,0.198 0.5,0.354 0.313,0.156 10 false *a 0.531,1.083 0.844,1.24 0.313,0.156 10 false P3 1.021,1.865 1.188,2.042 0.167,0.177 10 false E
*a Front view of wire harness connector
(to Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P3-5 (E) - Body ground Always Below 1 Ω



c.

Reconnect the P3 drive mode select switch (No. 1 pattern select switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH)
a.

Disconnect the H67 hybrid vehicle control ECU connector.


b.

Disconnect the P3 drive mode select switch (No. 1 pattern select switch assembly) connector.


c.
A368646C33
0.542,3.406 0.948,3.635 0.406,0.229 1.552,0.271 1.958,0.5 0.406,0.229 2.031,2.188 2.271,1.552 true 2.135,4.25 1.896,3.802 true 1.51,4.24 1.635,3.802 true 2.781,2.167 2.448,1.552 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.333,2.76 0.646,2.917 0.313,0.156 10 false *b 0.656,3.448 0.969,3.604 0.313,0.156 10 false P3 1.656,0.313 2.021,0.521 0.365,0.208 10 false H67 2.635,2.188 3.188,2.417 0.552,0.229 10 false DMS+ 2.083,4.302 2.75,4.51 0.667,0.208 10 false SEL 1.406,4.292 2.073,4.5 0.667,0.208 10 false E 1.906,2.219 2.458,2.448 0.552,0.229 10 false DMS-
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Drive Mode Select Switch (No. 1 Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-37 (DMS-) - P3-6 (E) Always Below 1 Ω
H67-38 (DMS+) - P3-7 (SEL) Always Below 1 Ω
H67-37 (DMS-) or P3-6 (E) - Body ground Always 10 kΩ or higher
H67-38 (DMS+) or P3-7 (SEL) - Body ground Always 10 kΩ or higher



d.

Reconnect the P3 drive mode select switch (No. 1 pattern select switch assembly) connector.


e.

Reconnect the H67 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR