The No. 1 skid control ECU (brake booster with master cylinder assembly) controls the brake fluid pressure of the master cylinder based on the output of the brake fluid pressure sensor.
DTCs may be stored if one of the following occurs:
Brake fluid leaks.
Foreign matter enters a solenoid valve.
Line pressure drops during air bleeding.
Brake pads are replaced.
Rotors are replaced.
Brake pressure control solenoid "C": Solenoid SLA
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C139A00 | Brake Pressure Control solenoid Circuit Malfunction | When all of the following conditions are met, there is a malfunction in one of the two circuits (leakage, etc.).
·
The vehicle was driven before the ignition switch was turned off. ·
90 seconds have elapsed since the ignition switch was turned off. ·
The vehicle is stopped and the shift position is P. |
·
Brake fluid leaks ·
Wire harness and connector ·
Brake booster with master cylinder assembly |
Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C13D900 | Brake Pressure Too Low (Brake Booster) | Fluid pressure control performance degraded (pressure excessively low) | ·
Brake fluid leaks ·
Wire harness and connector ·
Brake booster with master cylinder assembly |
Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14EC7E | Brake Pressure Control solenoid "C" Actuator Stuck On | SLA valve malfunction (stuck closed, etc.) | ·
Brake fluid leaks ·
Wire harness and connector ·
Brake booster with master cylinder assembly |
Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.
Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.
Freeze Frame Data is only stored once when a DTC is stored.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| Only DTCs C139A00, C13D900 and/or C14EC7E are output. | A |
| DTCs other than C139A00, C13D900 and/or C14EC7E are output. | B |
A
B
Based on the Freeze Frame Data or interview with the customer, inspect the following items for brake fluid leaks:
The brake lines from the brake booster with master cylinder assembly to each wheel cylinder.
The main body of the brake booster with master cylinder assembly and brake actuator assembly.
There are no fluid leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Perform the air bleeding procedure in Bleed Brake System.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage and resistance on the wire harness side.
Voltage and resistance readings are all normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C139A00, C13D900 and C14EC7E are not output. | A |
| DTCs C139A00, C13D900 and/or C14EC7E are output. | B |
| DTC C139A00 and C140A00 are output at the same time. | C |
If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector, air in the system, etc.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
for Brake Booster with Master Cylinder Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL
for Brake Actuator Assembly: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL