Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C13DA00  Brake Pressure Too High (Brake Booster)  


DESCRIPTION

Refer to DTCs C139A00, C13D900 and C14EC7E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C139A00

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C13DA00 Brake Pressure Too High (Brake Booster) Fluid pressure control performance degraded (pressure excessively high)
·

Foreign matter in solenoid valve

·

Wire harness and connector

·

Brake booster with master cylinder assembly


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>FREEZE FRAME DATA

Chassis > Brake Booster > Trouble Codes
50001 466
HINT:

Freeze Frame Data is only stored once when a DTC is stored.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only DTC C13DA00 is output. A
DTCs other than C13DA00 are output. B



A

4.PERFORM AIR BLEEDING

B

4.PERFORM AIR BLEEDING
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Perform the air bleeding procedure in Bleed Brake System.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING


Result:
Proceed to
NEXT



NEXT

5.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE)
5.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (ACTUATOR SIDE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)
a.

Reconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the voltage and resistance on the wire harness side.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TERMINALS OF ECU

OK:

Voltage and resistance readings are all normal.



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.RECONFIRM DTC
8.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
DTC C13DA00 is not output. A
DTC C13DA00 is output. B


HINT:

If the system returns to normal, it is suspected that a DTC was stored due to a poor connection of a terminal in a connector or foreign matter in a solenoid valve, etc.




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY