Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.02–2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C11031C  Brake Pedal Position Sensor "B" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC C110000.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C110000

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C11031C Brake Pedal Position Sensor "B" Supply Voltage Circuit Voltage Out of Range The sensor supply voltage (VSK2) is 4.7 V or less, or 5.3 V or more for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model LHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the A43 brake pedal stroke sensor assembly connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-26 (SKG2) - A43-3 (SKG2) Always Below 1 Ω
A57-26 (SKG2) or A43-3 (SKG2) - Body ground Always 10 kΩ or higher
A57-25 (VSK2) - A43-2 (VSK2) Always Below 1 Ω
A57-25 (VSK2) or A43-2 (VSK2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)
a.
C156491C87
0.333,1.167 0.75,1.417 0.417,0.25 1.417,2.313 1.135,2.896 true 1.885,2.917 1.625,2.313 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *a 0.406,1.208 0.719,1.406 0.313,0.198 10 false A43 1.76,2.938 2.26,3.208 0.5,0.271 10 false SKG2 0.927,2.938 1.365,3.177 0.438,0.24 10 false VSK2
*a Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly)


Reconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-2 (VSK2) - A43-3 (SKG2) Ignition switch ON 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG