Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL (for Dynamic Torque Vectoring AWD)
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0421145 REAR DIFFERENTIAL CARRIER OIL SEAL(for Dynamic Torque Vectoring AWD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL(for Dynamic Torque Vectoring AWD)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear differential carrier oil seal replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Gas leaks from exhaust system Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Torque vectoring differential carrier assembly
·

ECU data initialization

·

Disconnect system function check


Dynamic Torque Vectoring AWD System (Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 41110 1.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY

Hide 2.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41201C 6.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL (for Front Side)

a.
C418045C01
1.521,0.677 2.042,0.125 2.042,0.125 2.292,0.125 false 2.885,2.177 2.885,0.979 2.885,0.979 3.052,0.979 true 2.375,0.042 2.833,0.271 0.458,0.229 10 false SST 3.125,0.885 3.427,1.094 0.302,0.208 10 false *1
*1 Rear Differential Carrier Oil Seal


Using SST, remove the rear differential carrier oil seal from the rear differential carrier assembly.

SST
09308-00010  

NOTICE:

Do not damage the rear differential carrier oil seal press-fit surface.



b.
C418033

Remove the spacer.


c.
C418034C01
2.146,1.385 2.615,0.542 2.615,0.542 2.781,0.542 true 2.167,3.25 2.417,2.833 2.417,2.833 2.583,2.833 true 2.667,2.76 3.063,3.083 0.396,0.323 10 false SST 2.823,0.458 3.146,0.646 0.323,0.188 10 false *1
*1 Rear Drive Pinion Bearing (Inner Race)


Using SST, remove the rear drive pinion bearing (inner race).

SST
09556-40010  


d.
C418035

Remove the rear differential drive pinion bearing spacer.


e.

Using SST, remove the rear drive pinion bearing (outer race).

SST
09506-42030  
09950-40011  (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09957-04010)
09955-04160  

C418036C01
5.99,1.406 6.271,1.198 6.271,1.198 6.438,1.198 true 1.792,1.802 2.208,1.802 true 6.49,1.135 6.802,1.292 0.313,0.156 10 false *1 3.323,0.417 3.635,0.573 0.313,0.156 10 false *a 3.302,1.635 3.615,1.792 0.313,0.156 10 false *b 2.26,1.698 2.74,1.906 0.479,0.208 10 false SST
*1 Rear Drive Pinion Bearing (Outer Race) - -
*a Turn *b Hold



Hide 41201C 7.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL (for Front Side)

a.
C418037C01
2.188,1.677 2.604,1.677 true 1.844,3.313 2.26,3.313 true 2.365,3.24 2.948,3.656 0.583,0.417 10 false SST 2.677,1.604 3.042,1.823 0.365,0.219 10 false *1
*1 Rear Drive Pinion Bearing (Outer Race)


Using SST and a press, install the rear drive pinion bearing (outer race).

SST
09506-42010  


b.
C418035

Install a new rear differential drive pinion bearing spacer.


c.

Temporarily install the rear drive pinion companion flange sub-assembly.


d.
C418038C01
1.771,1.729 1.771,2.427 1.771,2.427 2.813,2.427 true 2.156,1.854 2.156,2.427 true 2.958,0.583 3.271,0.74 0.313,0.156 10 false *a 0.531,1.76 0.844,1.917 0.313,0.156 10 false *b 2.906,2.344 3.219,2.573 0.313,0.229 10 false SST
*a Turn
*b Hold


Using SST, install the rear drive pinion bearing (inner race).

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)


e.
C418032C01
1.802,1.729 1.802,2.333 1.802,2.333 2.833,2.333 true 2.125,1.833 2.125,2.333 true 2.521,1 2.833,1.156 0.313,0.156 10 false *a 0.854,0.51 1.167,0.667 0.313,0.156 10 false *b 2.875,2.26 3.302,2.479 0.427,0.219 10 false SST
*a Turn
*b Hold


Using SST, remove the rear drive pinion companion flange sub-assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)


f.
C418033

Install the spacer.


g.

Apply a small amount of MP grease to the lip of a new rear differential carrier oil seal.


h.
C418039C02
1.281,1.063 1.5,0.708 1.5,0.708 1.667,0.708 true 1.75,2.667 2.583,2.667 false 1.917,3.083 2.333,3.083 2.333,3.083 2.333,2.833 false 1.917,2.917 2.333,2.917 2.333,2.917 2.333,2.667 false 2.667,2.583 3.052,2.76 0.385,0.177 10 false SST 0.302,0.865 0.458,1.094 0.156,0.229 10 true A 1.708,0.635 2.021,0.792 0.313,0.156 10 false *1
*1 Rear Differential Carrier Oil Seal


Using SST, install the rear differential carrier oil seal to the rear differential carrier assembly.

SST
09554-42010  
09950-60021  (09951-01030)
09950-70010  (09951-07100)

Drive in depth (A):

5.7 to 6.3 mm (0.224 to 0.248 in.)


NOTICE:

Do not damage the rear differential carrier oil seal press-fit surface.


HINT:
C418050N01
2.677,1 2.885,1.208 0.208,0.208 10 false A

Press using the surface (A).



Hide 41204 8.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY